20170310143752.pdfiNrAs(,)
Site address
Seabrook Condos
221 3rd Ave S
Edmonds WA 98020
Scope of work
VIP
VALUE INSPECTION PROGRAM
i -7. 63423
ALL WORK SUBJECT
TO FIELD
INSPECTION FOR
CODE COMPLIANCE
Like for like panel exchange Firelight MS4. To replace existing panel with faulty circuit board and
reversed polarity on the NAC devices. After hours emergency panel replacement. Panel located in the
breezeway carport midway down the north side of the building.
Contractor
Cintas Fire Protection
3320 W Valley Hwy N #D111
Auburn WA 98001
253.852.1962
CINTAFP903DK
Jeff Hale
Halei@cintas.com
Property Manager
Cay COPS
RECEOvED,
MAR 10 2017
DEVELOPMENT SERVICES
COUNTER
Cintas Fire Protection stands behind every service visit to guarantee every customer is satisfied
DF-5226632 • A2-260
MS-4(E)
Fire Alarm Control Panel
General
The Fire-Lite MS-4 and MS-4E Fire Alarm Control Panels
(FACPs) bring the latest in microprocessor technology to con-
ventional fire controls. The MS-4 is compatible with the i3rm
smoke detectors from System Sensor, with drift compensation,
maintenance alert, and freeze warning. Automatic synchroniza-
tion of audio/visual devices with three selections for manufac-
turer protocol. The Notification Appliance Circuit (NAC) protocol
can silence audible devices while strobes continue to flash,
using a single pair of wires.
The MS-4 is compatible with conventional input devices such as
two- and four -wire smoke detectors, pull stations, waterflow
devices, tamper switches and other normally -open contact
devices. Refer to the Fire-Lite Device Compatibility Document
for a complete list of compatible devices.
Note: Unless indicated otherwise, the term 'MS-4" refers to both
MS-4 and MS-4E models.
Features
• Four Style B (Class B) Initiating Device Circuits (IDCs).
• Two Style Y (Class B) NACs.
• Optional module that converts all four IDCs and two NACs to
Class A operation.
• 24 VDC.
• i3TM Technology features:
— Drift compensation automatically adjusts detector sensitiv-
ity and increases resistance to false alarms caused by dust
accumulation.
— Maintenance Alert LEDs (per zone) warn of excessive dirt
accumulation, preventing false alarms (meets NFPA 72
requirements).
— Detector sensitivity is automatically measured by the
detector, which automatically adjusts its sensitivity back to
the factory settings when it becomes more sensitive due to
contaminants settling in the chamber.
— Wireless handheld sensitivity meter eliminates the need for
voltmeters, magnets, and a physical connection to the
detector. The reader displays sensitivity in terms of percent
per foot obscuration and provides text status indication.
— Supervisory LED (per zone) provides warning if a detector
senses temperature approaching freezing.
— Special test protocol and LED indication allows quick test of
all detectors without need for a ladder.
• NAC synchronization features:
— Synchronization of standard ANSI audible signals as
required by NFPA 72.
— Synchronization of ADA compliant strobes per NFPA 72.
— Selectable for System Sensor, Wheelock, and Gentex
protocols.
— Selective Silence feature for manual silence of horns
while strobes continue to flash on the same NAC.
— Alarm verification selectable for each zone.
— Disable switches provided per zone.
• NACs programmable for.
— Silence Inhibit
— Auto Silence
— Strobe Synchronization
— Selective Silence (horn -strobe mute)
— Temporal or Steady signal
— Silenceable or Nonsilenceable
(2) Fire•uTe ALarms
by Honeywell
• Silent or audible Walk Test operation mode commanded from
the front keypad, with automatic return -to -normal after one
hour of inactivity.
• Each zone may be programmed for supervisory or fire; each
zone has separate red and yellow LEDs.
• Zone 4 is programmable for combination of tamper supervi-
sory monitoring and waterflow alarm.
• Form-C Alarm, Trouble, and Supervisory relays.
• 3.0 A total usable current.
• 6.0 A total usable current available with optional second
transformer.
• Control buttons:
— ACK (Acknowledge)
— Alarm Silence
— Reset
— Walk Test
— Zone Enable/Disable (one per zone)
• LED indicators:
— Fire Alarm (one per zone)
— Supervisory (one per zone)
— Trouble (one per zone)
— Maintenance (one per zone)
— AC Power
— NAC Disable
— Zone Disable
— NAC Fault
— System Trouble
— Power Trouble
— Walk Test
— Alarm Silence
— Earth Fault (on circuit board)
— Battery Fault (on circuit board)
— Charger Fault (on circuit board)
• Piezo sounder for alarm, trouble, supervisory and mainte-
nance.
• Optional plug-in 4XTMF transmitter module.
• Optional plug-in 4XZMF zone relay module.
• Optional 4XLMF transmitter module for RZA-4XF remote
LED annunciator.
• Optional dress panel.
DF-52266:B2 • 12/21/2012 — Page 1 of 2
Operation
Activation of a compatible smoke detector or any normally -open
fire alarm initiating device activates audible and visual signaling
devices, illuminates an indicating LED, sounds the piezo
sounder at the FACP, activates the FACP alarm relay and oper-
ates an optional module used to notify a remote station or initi-
ate an auxiliary control function.
Specifications
AC POWER - T83
• MS-4: 120 VAC, 50/60 Hz, 2.3 A.
• MS-4E: 240 VAC, 50 Hz, 1.15 A.
• Wire Size: Minimum 14 AWG (2.0 mm2) with 600 V insulation.
BATTERY (SEALED LEAD -ACID ONLY) - J8
• Maximum charging circuit: normal flat charge 27.6 VCD @
0.8 A.
• Maximum battery charger capacity: 18.0 AH battery (two
7.0 AH batteries can be housed in the FACP cabinet. Larger
batteries require a separate battery box such as the Fire-Lite
BB-17F).
INITIATING DEVICE CIRCUITS- TB3
• Alarm zones 1 - 4.
• Power -limited circuitry.
• Operation: all zones Style B (Class B).
• Normal operating voltage: nominal 20 VDC.
• Alarm current: 15 mA minimum.
• Short-circuit current: 40 mA maximum.
• Maximum loop resistance: 100 ohms.
• End -of -line resistor: 4.7K ohm, 1/2 watt (P/N 71252).
• Standby current: 4 mA.
• Compatible devices: refer to the Fire-Lite Device Compatibil-
ity Document PN 15384 for a complete list of compatible
devices.
NOTIFICATION APPLIANCE CIRCUITS - T82
• Two NACs.
• Power -limited circuitry.
• Normal operating voltage: nominal 24 VDC.
• Maximum signalling current: 2.5 A total with standard trans-
former 5.0 A total (2.5 A maximum per NAC) with optional
transformer.
• End -of -line resistor: 4.7K ohm, 1/2 watt (P/N 71252).
• Compatible devices: refer to the Fire-Lite Device Compatibil-
ity Document PN 15384 for a complete list of compatible
devices.
FORM-C RELAYS
• Trouble Relay TB5 (fail-safe).
• Alarm Relay TB6.
• Supervisory relay TB7.
• Relay contact ratings: 2.0 A @ 30 VDC (resistive).
AUXILIARY OUTPUT. RESETTABLE POWER - TB1
• Operating voltage: nominal 24 VDC.
• Maximum available current: 500 mA - appropriate for pow-
ering four -wire smoke detectors (see notes).
• Power -limited circuitry.
Notes: 1) Refer to the Fire-Lite Device Compatibility Document
for a complete list of compatible devices.
2) Total current for nonresettable power, resettable power and
two NACs must not exceed 6.0 A for the MS-4 (required optional
second transformer).
CABINET DIMENSIONS
Door: 15.342" (38.97 cm) high x 14.667" (37.28 cm) wide x
0.375" (0.95 cm) deep.
Backbox: 15.0" (38.10 cm) high x 14.5' (36.83 cm) wide x 3.0"
(7.62 cm) deep.
BACKBOX MOUNTING
The cabinet can be surface mounted. The door is removable
during installation by opening and lifting it off the hinges. The
cabinet mounts using two key slots at the top of the backbox and
two additional 0.25' diameter holes at the bottom.
Listings and Approvals
• UL Listed: S624
• MEA:297-01-E
• CSFM:7165-0075:200
Ordering Information
MS-4: Four -zone conventional FACP; 120 VAC, 50/60 Hz, 2.3 A.
MS-4E: Same as above, but 240 VAC, 50 Hz, 1.15 A operation.
CAC-4: Class A converter module. Used to convert Style B
(Class B) IDC to Style D (Class A) and Style Y (Class B) NAG to
Style Z (Class A). The module connects to J1 on the MS-4 cir-
cuit board.
4XTMF: Transmitter module.
4XLMF: LED interface module.
4XZMF: Zone relay module, 4 form C relay.
RZA:-4XF: Remote Annunciator.
BB-17F: Battery box, required to house two batteries greater
than 7 AH to a maximum of 18 AH.
4111411UD: Three -input (channels) model 411, and four -input
model 411UD, dual -line Digital Alarm Communicator/Transmit-
ters (DACTs). Can be used as slave communicators with the
FACP.
DP-MS2/4: Optional dress panel.
MS-4RB: Replacement board.
TRA-R: Optional trim ring for semi -flush mounting.
A 2-zone version of this panel is also available. See DF-52211.
Fire-Lite® Alarms is a registered trademark of Honeywell International Inc.
02011 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
I�O �oo�
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
_
We cannot cover all specific applications or anticipate all requirements.
EHOINEEIINC B 111M A6INS
QUALITY SYSTEMS
All specifications are subject to change without notice.
For more information, contact Fire-Lite Alarms. Phone: (800) 627-3473, FAX: (877) 699-4105.
www,firelite.com
Made in the U.S. A.
Page 2 of 2 - DF-52266:B2 • 12/21/2012