Mock Residence Foundation Stabilization Structural Observation Report #3 08.12.19 (1)C �
ENGINEERING
civil & structural
engineering & planning
STRUCTURAL OBSERVATION REPORT
Project: Mock Residence Slope Stabilization
Purpose: Structural Evaluation
Location: 21100 88th PI West
Date: August 12, 2019
CG Project: 18295.10
Report: 3
Client: Darrin Mock
General Contractor: Unknown
Field Rep: Morgan Kruse, PE
PURPOSE AND SCOPE
A field representative of CG Engineering was on site on August 5, 2019 to observe the structural slab
dowel bar installation to the existing foundation. Prior to our site visit, approximately 75'-0" total
length of concrete grade beam had been poured and completed, along with the block retaining wall
below the structural slab.
EXISTING BUILDING
The existing building is a single family residential structure that had experienced settlement to the
downhill side. The existing rockery wall at the edge of the rear patio was removed and will be replaced
with an allan block and geogrid wall system supported by a concrete grade beam. The concrete patio
slab will then be replaced with a new structural slab. At the time of our site visit, the entire length of
grade beam was completed and the block wall was installed.
To the best of our knowledge, the construction that we observed was in accordance with the approved
structural drawings with the exception of the items listed below:
OBSERVATIONS & RECOMMENDATIONS
1. Structural Slab Reinforcing — Prior to our arrival on site, the holes for the dowel bars were
drilled into the existing footing and cleaned as required for the epoxy installation. During our
site visit, the epoxy was inserted into the drilled holes, and the dowel bars were inserted. The
epoxy used was USP CIA -GEL 7000-C and Sika Pro Select. The slab dowel bars and epoxy
appeared to conform to the construction documents and no issues were noted.
rGUrl
WAZ
C4�n, ag �
OVAL /
DISCLAIMER
This observation is the professional opinion of CG Engineering PLLC based on the information available during this assessment or evaluation.
This report does not warrant or guarantee that all conditions were discovered at the time of the observation. This report was prepared subject
to the standard of care applicable to professional services at the time the services were provided. 250 4th Avenue South, Suite 200
Edmonds, WA 98020
ph.425.778.8500 1 f.425.778.5536
www.cgengineering.com
Mock Residence Foundation Stabilization
CG Project No. 18295.10
August 12, 2019
Page 2 of 4
C 4M
ENGINEERING
�-
CUSP CIA -GEC
760 voxv
rF
SiAIC1AAAl CUNCiunu
xlee or eo��IrrN I,
jffNgYfD f0jl C/AC9Eft Aft
I#CJTwCan Apa1Cl"ONS r.� • � ...
PER/CC-ESAe30B
nveonnoovanIES
Aavu
9H Erns
CON GRIETAS Y
4 • .
Ok
• ,�. ,,.� 1� -
r
-,ZZ1eclars.c0111 �,y� r�•''t ai
Itp-77s.5931 �certn.u[�.�i' 1I f!t .
.p- Ir 61 �a �
iIUP IOC 19 .. '1'� ..i `' �. •�� ~' �((('� ,� rr�t�,
Photo 1— Epoxy used for installation
Photo 2 — Epoxy used for installation
250 4th Avenue South, Suite 200
Edmonds, WA 98020
ph.425.778.8500 1 f.425.778.5536
www.cgengineering.com
Mock Residence Foundation Stabilization
CG Project No. 18295.10
August 12, 2019
Page 3 of 4
Photo 3 — Slab dowel bars
Photo 4 — Slab dowel bars
C � 250 4th Avenue South, Suite 200
Edmonds, WA 98020
ENGINEERING ph.425.778.8500 1 f.425.778.5536
www.cgengineering.com
Mock Residence Foundation Stabilization
CG Project No. 18295.10
August 12, 2019
Page 4 of 4
Photo —_Slab dowel bars
J
Photo 6 — Slab dowel bars
250 4th Avenue South, Suite 200
C Edmonds, WA 98020
ENGINEERING ph.425.778.8500 1 f.425.778.5536
www.cgengineering.com