FIR2020-0073+Fire_Sprinkler_Equipment_Specification_Sheets+8.4.2020_1.24.17_PMBulletin 006 May 2019
Reliable
Features
cULus Listed as Residential Sprinklers
Push -On cover plate installation
Low water flow requirements
Product Description
Model RFC Series residential sprinklers are flat cover plate,
concealed pendent sprinklers intended for installation in
accordance with NFPA 13, NFPA 13R, or NFPA 13D. The
sprinklers are cULus Listed as Residential Sprinklers in ac-
cordance with UL 1626. In addition, Model RFCLL Series
sprinklers are cULus Certified for Health Effects to NSF/ANSI
standard 61 Annex G (LL) and Australian WaterMark Certified
(WMCS).
Model RFC30 sprinklers have a 1650F (74°C) temperature
rated fusible -link operating element. Model RFC43, RFC49,
RFC58, and RFC76 sprinklers are offered with either a 1650F
(74°C) or 212OF (100°C) temperature rated fusible -link oper-
ating element. Sprinklers with a 1650F (74°C) temperature
rating are ordinary temperature classification and are listed
for use with a 1350F (57°C) temperature rated cover plate.
Sprinklers with a 212OF (100°C) temperature rating are inter-
mediate temperature classification and are listed for use with
a 1650F (74°C) temperature rated cover plate.
Model RFC Series sprinklers are installed with a Model RFC
cover plate. Model RFC cover plates may be installed by ei-
ther pushing or threading the cover plate into the sprinkler
cup. Model RFC30, RFC30LL, RFC43, RFC43LL, RFC49 and
RFC49LL sprinklers allow 1/2" (13 mm) of cover plate adjust-
ment. Model RFC58 and RFC76 sprinklers allow 3/4" (19 mm)
of cover plate adjustment. Model RFC cover plates are avail-
able in a variety of finishes as listed in Table H.
Model RFC Series Residential Sprinklers
Flat Concealed Pendent
Model RFC30 & RFC30LL
Model RFC49 & RFC49LL
Model RFC76
cULus Listed
Model RFC43 & RFC43LL
Model RFC58
)M
Model RFC Cover Plate
Sprinkler Model
Nominal K-Factor
gpm/psi (1/min/bary/Z )
Max. Coverage Area
ft x ft (m x m)
Listings &
Approvals
Sprinkler Identification
Number (SIN)
RFC30
3.0(43)
14 x 14 (4.3 x 4.3)
cULus
RA0611
RFC30LL
3.0(43)
14 x 14 (4.3 x 4.3)
cULus, LL, WMCS
RA3211
RFC43
4.3(62)
20 x 20 (6.1 x 6.1)
cULus
RA0612
RFC43LL
4.3(62)
20 x 20 (6.1 x 6.1)
cULus, LL, WMCS
RA3212
RFC49
4.9(71)
20 x 20 (6.1 x 6.1)
cULus
RA0616
RFC49LL
4.9(71)
20 x 20 (6.1 x 6.1)
cULus, LL, WMCS
RA3216
RFC58
5.8(84)
20 x 20 (6.1 x 6.1)
cULus
RA0613
RFC76
7.6(109)
20 x 20 (6.1 x 6.1)
cULus
RA0618
cULus: cULus Listed to UL1626, Residential Sprinklers for Fire Protection Service.
LL: cULus Certified for Health Effects to NSF/ANSI Standard 61 Annex G (Less than 0.25% Lead content).
WMCS: Australian WaterMark Certified.
www.reliablesprinkler.com
Technical Specifications
Style: Flat Concealed Pendent
Threads: 1/2" NPT or ISO 7-1 R1/2
Nominal K-Factor: 3.0 (43 metric)
Max. Working Pressure: 175 psi (12 bar)
Min. Spacing: 8 ft. (2.4 m)
Material Specifications
Thermal Sensor: Nickel Alloy Solder Link
Sprinkler Body: Brass Alloy
Levers: Bronze Alloy
Yoke: Brass Alloy
Sealing Assembly: Nickel Alloy with PTFE
Load Screw: Bronze Alloy
Towers: Copper Alloy
Pins: Stainless Steel
Deflector: Bronze Alloy
Cup: Steel
Cover Plate Finishes
(See Table H)
Sensitivity
Fast -response
Temperature Rating
165°F (74°C) sprinkler
135°F (57°C) cover plate
Cover Plate
Model RFC cover plate
Sprinkler Wrench
Model FC (without wrench -able cap)
Model W3 (with wrench -able cap)
Listings and Approvals
cULus Listed to UL 1626
cULus Certified for Health Effects to NSF/ANSI
Standard 61 Annex G (RFC30LL only)
Watermark Certified (RFC30LL only)
Model RFC30 & RFC30LL Sprinkler Components and Dimensions
Threads —
Body
Cup —�
Tower
Fusible Link —
Deflector (retracted)
Pin (extended) -
Deflector (extended)
1-3/4" (44 mm) +/- 1/4" (6 mm)
Nominal face of fitting to ceiling
Bottom View
2-5/16" (58 mm)
Dia.
3/16"(5mm'
Model RFC Cover Plate i 3-5/16" (84 mm) Dia. —►{ N Ceiling
Model RFC30 and RFC30LL Sprinkler Hydraulic Design Criteria
Minimum Flow and Residual Pressure
Max. Coverage Area (2)
Flow
Pressure
ft. x ft.
gpm
psi
(m x m)
(1/min)
(bar)
12 x 12
9
9.0
(3.6 x 3.6)
(34)
(0.62)
14 x 14
10
7
11.0
(4.3 x 4.3)
(38)
(0.76)
Notes:
1. For NFPA 13 installations the flow per sprinkler must be the greater of: (1) the flow listed in Table B above and (2) the flow required to
achieve a minimum design density of 0.1 gpm/sq ft over the design area of the sprinkler.
2. For coverage area dimensions less than those listed above, use the minimum required flow for the next larger max. coverage area listed.
Bulletin 006 Reliable Page 2 of 8
May 2019 www.reliablesprinkler.com
Technical Specifications
Style: Flat Concealed Pendent
Threads: 1/2" NPT or ISO 7-1 R1/2
Nominal K-Factor: 4.3 (62 metric)
Max. Working Pressure: 175 psi (12 bar)
Min. Spacing: 8 ft. (2.4 m)
Material Specifications
Thermal Sensor: Nickel Alloy Solder Link
Sprinkler Body: Brass Alloy
Levers: Bronze Alloy
Yoke: Brass Alloy
Sealing Assembly: Nickel Alloy with PTFE
Load Screw: Bronze Alloy
Towers: Copper Alloy
Pins: Stainless Steel
Deflector: Bronze Alloy
Cup: Steel
Cover Plate Finishes
(See Table H)
Sensitivity
Fast -response
Temperature Rating
Ordinary:
165°F (74°C) sprinkler
135°F (57°C) cover plate
Intermediate:
212°F (100°C) sprinkler
165°F (74°C) cover plate
Cover Plate
Model RFC cover plate
Sprinkler Wrench
Model FC (without wrench -able cap)
Model W3 (with wrench -able cap)
Listings and Approvals
cULus Listed to UL 1626
cULus Certified for Health Effects to NSF/ANSI
Standard 61 Annex G (RFC43LL only)
Watermark Certified (RFC43LL only)
Model RFC43 & RFC43LL Sprinkler Components and Dimensions
Threads
Body
Cup
Tower
Fusible Link
Deflector (retracted)
Pin (extended)
Deflector (extended) -
1-3/4" (44 mm) +/- 1/4" (6 mm)
Nominal face of fitting to ceiling
Model RFC Cover Plate
Model RFC43 & RFC43LL Sprinkler Hydraulic Design Criteria
6
Bottom View ,
2-5/16" (58 mm)
Dia.
- a-1
3-5/16" (84 mm) Dia.
3/16" (5 mm'
Ceiling
Minimum Flow and Residual Pressure
Max. Coverage Area (2)
Ordinary Temperature
Intermediate Temperature
Flow
Pressure
Flow
Pressure
ft. x ft.
(m x m)
gpm
psi
gpm
psi
(1/min)
(bar)
(1/min)
(bar)
15 x 15
12
7.8
12
7.8
(4.6 x 4.6)
(45)
(0.54)
(45)
(0.54)
16 x 16
13
9.1
13
9.1
(4.9 x 4.9)
(49)
(0.63)
(49)
(0.63)
18 x 18
18
17.5
(5.5 x 5.5)
(68)
(1.21)
20 x 20
21
23.8
(6.1 x 6.1)
(79)
(1.64)
Notes:
1. For NFPA 13 installations the flow per sprinkler must be the greater of: (1) the flow listed in Table C above and (2) the flow required to
achieve a minimum design density of 0.1 gpm/sq ft over the design area of the sprinkler.
2. For coverage area dimensions less than those listed above, use the minimum required flow for the next larger max. coverage area listed.
Bulletin 006 Reliable Page 3 of 8
May 2019 www.reliablesprinkler.com
Technical Specifications
Style: Flat Concealed Pendent
Threads: 1/2" NPT or ISO 7-1 R1/2
Nominal K-Factor: 4.9 (71 metric)
Max. Working Pressure: 175 psi (12 bar)
Min. Spacing: 8 ft. (2.4 m)
Material Specifications
Thermal Sensor: Nickel Alloy Solder Link
Sprinkler Body: Brass Alloy
Levers: Bronze Alloy
Yoke: Brass Alloy
Sealing Assembly: Nickel Alloy with PTFE
Load Screw: Bronze Alloy
Towers: Copper Alloy
Pins: Stainless Steel
Deflector: Bronze Alloy
Cup: Steel
Sensitivity
Fast -response
Temperature Rating
Ordinary:
165°F (74°C) sprinkler
135°F (57°C) cover plate
Intermediate:
212°F (100°C) sprinkler
165°F (74°C) cover plate
Cover Plate
Model RFC cover plate
Sprinkler Wrench
Model FC (without wrench -able cap)
Model W3 (with wrench -able cap)
Cover Plate Finishes Listings and Approvals
cULus Listed to UL 1626
(See Table H) cULus Certified for Health Effects to NSF/ANSI
Standard 61 Annex G (RFC49LL only)
Watermark Certified (RFC49LL onlv)
Model RFC49 & RFC49LL Sprinkler Components and Dimensions
Threads
Body —
Cup
Tower
Fusible Link
Deflector (retracted)
Pin (extended)
Deflector (extended)
1-3/4" (44 mm) +/- 1/4" (6 mm)
Nominal face of fitting to ceiling
Bottom View
2-5/16" (58 mm)
Dia.
Model RFC Cover Plate 3-5/16" (84 mm) Dia. �-- Ceiling
Model RFC49 & RFC49LL Sprinkler Hydraulic Design Criteria
Minimum Flow and Residual PressureM
Max. Coverage Area (Z)
Ordinary Temperature
Intermediate Temperature
Flow
Pressure
Flow
Pressure
ft. x ft.
(m x m)
gpm
psi
gpm
psi
(1/min)
(bar)
(1/min)
(bar)
16 x 16
13
7.0
13
7.0
(4.9 x 4.9)
(49.0)
(0.48)
(49.0)
(0.48)
18 x 18
17
12.0
17
12.0
(5.5 x 5.5)
(64.3)
(0.83)
(64.3)
(0.83)
20 x 20
20
16.7
21
18.4
(6.1 x6.1)
(75.7)
(1.15)
(79.5)
(1.27)
Notes:
1. For NFPA 13 installations the flow per sprinkler must be the greater of: (1) the flow listed in Table D above and (2) the flow required to
achieve a minimum design density of 0.1 gpm/sq ft over the design area of the sprinkler.
2. For coverage area dimensions less than those listed above, use the minimum required flow for the next larger max. coverage area listed.
Bulletin 006 Reliable Page 4 of 8
May 2019 www.reliablesprinkler.com
Technical Specifications
Style: Flat Concealed Pendent
Threads: 1/2" NPT or ISO 7-1 R1/2
Nominal K-Factor: 5.8 (84 metric)
Max. Working Pressure: 175 psi (12 bar)
Min. Spacing: 8 ft. (2.4 m)
Material Specifications
Thermal Sensor: Nickel Alloy Solder Link
Sprinkler Body: Brass Alloy
Levers: Bronze Alloy
Yoke: Brass Alloy
Sealing Assembly: Nickel Alloy with PTFE
Load Screw: Bronze Alloy
Towers: Copper Alloy
Pins: Stainless Steel
Deflector: Chrome Plated Bronze Alloy
Cup: Steel
Cover Plate Finishes
(See Table H)
Sensitivity
Fast -response
Temperature Ratings
Ordinary:
165°F (74°C) sprinkler
135°F (57°C) cover plate
Intermediate:
212°F (100°C) sprinkler
165°F (74°C) cover plate
Cover Plate
Model RFC Cover Plate
Sprinkler Wrench
Model FC (without wrench -able cap)
Model W3 (with wrench -able cap)
Listings and Approvals
cULus Listed
Model RFC58 Sprinkler Components and Dimensions
Bottom View
2-5/16" (58 mm) y
Dia.
Threads _
Body _
Cup =_
Tower
Fusible Link 1-7/8" (48 mm) +/- 3/8" (9 mm)
Deflector (retracted) Nominal face of fitting to ceiling
� Pin (extended) 7", 3/16"(5mm,
"""`
Deflector (extended)
Model RFC Cover Plate 3-5/16" (84 mm) Dia. Ceiling
Model RFC58 Sprinkler Hydraulic Design Criteria
Minimum Flow and Residual Pressure')
Max. Coverage Area (2)
Flow
Pressure
ft. x ft.
gpm
psi
(m x m)
(1/min)
(bar)
16 x 16
16
7.6
(4.9 x 4.9)
(60.6)
(0.53)
18 x 18
18
9.6
(5.5 x 5.5)
(68.1)
(0.66)
20 x 20
20
11.9
(6.1 x 6.1)
(75.7)
(0.82)
Notes:
1. For NFPA 13 installations the flow per sprinkler must be the greater of: (1) the flow listed in Table E above and (2) the flow required to
achieve a minimum design density of 0.1 gpm/sq ft over the design area of the sprinkler.
2. For coverage area dimensions less than those listed above, use the minimum required flow for the next larger max. coverage area listed.
Bulletin 006 Reliable Page 5 of 8
May 2019 www.reliablesprinkler.com
Technical Specifications
Style: Flat Concealed Pendent
Threads: 3/4" NPT or ISO 7-1 R3/4
Nominal K-Factor: 7.6 (109 metric)
Max. Working Pressure: 175 psi (12 bar)
Min. Spacing: 8 ft. (2.4 m)
Material Specifications
Thermal Sensor: Nickel Alloy Solder Link
Sprinkler Body: Brass Alloy
Levers: Bronze Alloy
Yoke: Brass Alloy
Sealing Assembly: Nickel Alloy with PTFE
Load Screw: Bronze Alloy
Towers: Copper Alloy
Pins: Stainless Steel
Deflector: Bronze Alloy
Cup: Steel
Cover Plate Finishes
(See Table H)
Sensitivity
Fast -response
Temperature Ratings
Ordinary:
165°F (74°C) sprinkler
135°F (57°C) cover plate
Intermediate:
212°F (100°C) sprinkler
165°F (74°C) cover plate
Cover Plate
Model RFC Cover Plate
Sprinkler Wrench
Model FC (without wrench -able cap)
Model W3 (with wrench -able cap)
Listings and Approvals
cULus Listed
Model RFC76 Sprinkler Components and Dimensions
Three
Body
Cup
Towei
Fusible Li
Deflector (retra
Pin (extern
Deflector (extend
1-7/8" (48 mm) +/- 3/8" (9 mm)
Nominal face of fitting to ceiling
Model RFC Cover Plate
Model RFC76 Flat Concealed Sprinkler Hydraulic Design Criteria
/o
Bottom View
ti
2-5/16" (58 mm)
Dia.
3-5/16" (84 mm) Dia.
3/16" (5 mm)
Ceiling
Minimum Flow and Residual PressureN
Max. Coverage Area (2)
Flow
Pressure
ft. x ft.
gpm
psi
(m x m)
(1/min)
(bar)
16 x 16
21
7.6
(4.9 x 4.9)
(79.5)
(0.52)
18 x 18
24
9.9
(5,5 x 5.5)
(90.8)
(0.68)
20 x 20
34
20
(6,1 x 6.1)
(128.7)
(1.4)
Notes:
1. For NFPA 13 installations the flow per sprinkler must be the greater of: (1) the flow listed in Table E above and (2) the flow required to
achieve a minimum design density of 0.1 gpm/sq ft over the design area of the sprinkler.
2. For coverage area dimensions less than those listed above, use the minimum required flow for the next larger max. coverage area listed.
Bulletin 006 Reliable Page 6 of 8
May 2019 www.reliablesprinkler.com
Cover Plate Finishes(')
Standard Finishes Special Application Finishes
White Polyester Off White Paint Black Paint Raw Brass
Chrome Plated Bright Brass Finished Bronze Black Plated
Satin Chrome Stainless Steel Clad (3) Custom Color Paint(2)
Notes:
1. Paint or any other coating applied over the factory finish will void all approvals and warranties.
2. Custom color paint is semi -gloss, unless specified otherwise.
3. Stainless steel clad cover plates are Type 316 Stainless Steel on the finished side and C102 Copper Allow on the backside. Cover plates
are not listed or approved as corrosion resistant. Stainless steel clad cover plates are not available perforated.
Installation Dimensions
Recommended
Min. to
Min. to Max.
Sprinkler
Cover
Cover Plate
Hole Diameter
Cover Plate
Max. Face
Dropped Deflector
Cover Plate
Model
Plate
Diameter
in Ceiling
Adjustment
of Fitting to
Distance below
Temperature
Model
inch (mm)
inch (mm)
inch (mm)
Ceilings')
Ceiling
Rating
inch (mm)
inch (mm)
RFC30,
RFC
3-5/16
2-5/8
1/2
1-1/2 to 2
1/2 to 1
1350F
RFC30LL
(84)
(67)
(13)
(38 to 51)
(13 to 25)
(57°C)
RFC43,
1350F(2)
RFC43LL,
RFC
3-5/16
2-5/8
1/2
1-1/2 to 2
1/2 to 1
(57°C)
RFC49,
(84)
(67)
(13)
(38 to 51)
(13 to 25)
or 1650F 3
RFC49LL
(74°C)
1350F(2)
RFC58,
RFC
3-5/16
2-5/8
3/4
1-1/2 to 2-1/4
1/4 to 1
(57°C)
RFC76
(84)
(67)
(19)
(38 to 57)
(6 to 25)
or 165°F3
(74°C)
Notes:
1. Face of fitting to ceiling dimensions are based on a nominal thread make up. Verify dimensions based on fitting and thread sealing method
prior to installation. A 1/2" x 1/2" brass nipple extension (Reliable P/N 6999991900) is available where necessary for replacement of existing
sprinklers.
2. For use with 165°F (74°C) temperature rated sprinklers where the Maximum Ceiling Temperature does not exceed 100°F (38°C).
3. For use with 212°F (100°C) temperature rated sprinklers where the Maximum Ceiling Temperature does not exceed 150°F (66°C).
Installation
Model RFC series sprinklers are intended to be installed in ac-
cordance with NFPA 13, NFPA 13R, or NFPA 13D, as well as the
requirements of applicable authorities having jurisdiction. Mod-
el RFC series sprinklers must not be installed in ceilings with
positive pressure in the space above. Ensure that the 4 slots in
the cup are open and unobstructed following installation. Model
RFC series sprinklers are shipped with a wrench -able protec-
tive cap that should remain on the sprinkler until the sprinkler
system is placed in service following construction.
Model RFC series sprinklers can be installed without removing
the wrench -able protective cap using the Model W3 wrench.
Alternatively, Model RFC series sprinklers can be installed us-
ing the Model FC wrench by temporarily removing the protec-
tive cap during installation of the sprinkler. The use of any other
wrench to installed Model RFC series sprinklers is not permit-
ted and may damage the sprinkler. Fully insert the Model W3
wrench over the cap until it reaches the bottom of the cup, or
the Model FC wrench over the sprinkler until the wrench engag-
es the body. Do not wrench any other part of the sprinkler/cup
assembly. The Model W3 and FC wrenches are designed to be
turned with a standard 1/2" square drive. Tighten the sprinkler
into the fitting after applying a PTFE based thread sealant to the
sprinkler's threads. Recommended installation torque is 8 to 18
ft-Ibs (11 to 24 N-m) for 1/2" thread sprinklers and 14 to 20 ft-Ibs
(19 to 27 N-m) for 3/4" thread sprinklers.
Do not exceed the maximum recommended torque. Exceeding
the maximum recommended torque may cause leakage or im-
pairment of the sprinkler. Use care when inserting or removing
the wrench from the sprinkler to avoid damage to the sprinkler.
Install the cover plate by hand by pushing the cover plate into
the cup and turning the cover in the clockwise direction until it
is tight against the ceiling.
Application
Model RFC series sprinklers are intended for installation where
residential sprinklers are permitted or required by NFPA 13,
NFPA 13R, and NFPA 13D. The sprinklers are concealed pen-
dent residential sprinklers.
Model RFC 30 and RFC30LL sprinklers are available in ordinary
temperature classification for installation where the Maximum
Ceiling Temperature does not exceed 100OF (380C). Model
RFC43, RFC43LL, RFC49, RFC49LL, RFC58, and RFC76 sprin-
klers are available in either ordinary or intermediate tempera-
ture classification for installation where the Maximum Ceiling
Temperature does not exceed 100OF (38°C) or 150OF (660C),
respectively.
Bulletin 006
May 2019
Page 7 of 8
www.reliablesprinkler.com
Model FC
For use with Model RFC Series sprinklers
without wrench -able cap installed
Maintenance
Model RFC series sprinklers should be inspected and the
sprinkler system maintained in accordance with NFPA 25. Do
not clean sprinklers with soap and water, ammonia or any other
cleaning fluids. Remove dust by gentle vacuuming. Replace
any sprinkler cover plate assembly which has been painted
(other than factory applied) or damaged in any way. A stock of
spare sprinklers should be maintained to allow quick replace-
ment of damaged or operated sprinklers. Prior to installation,
sprinklers should be maintained in the original cartons and
packaging until used to minimize the potential for damage to
sprinklers that would cause improper operation or non -oper-
ation.
Listings and Approvals
Listed by Underwriters Laboratories, Inc. and UL Certified for
Canada to UL1626, Residential Sprinklers for Fire -protection
Service (cULus).
Certified by Underwriters Laboratories, Inc. and Underwrit-
ers Laboratories of Canada for Health Effects to NSF/ANSI
Standard 61 Annex G (LL) (RFC30LL, RFC43LL, and RFC49LL
only).
Australian WaterMark Certified (RFC30LL, RFC43LL, and
RFC49LL only).
Model W3
For use with Model RFC Series sprinklers
with wrench -able cap installed
Guarantee
For the Reliable Automatic Sprinkler Co., Inc. guarantee, terms,
and conditions, visit www.reliablesprinkler.com.
Patents
Model RFC30, RFC30LL, RFC43, RFC43LL, RFC49, RFC49LL,
RFC58, and RFC76 sprinklers are covered by U.S. Patent No.
9,248,327 and U.S. Patent No. 7,275,603.
Model RFC30, RFC30LL, RFC43 and RFC43LL sprinklers are
additionally covered by U.S. Patent No. 8,776,903.
Ordering Information
Specify the following when ordering.
Sprinkler
• Model (RFC30, RFC30LL, RFC43, RFC43LL,
RFC49, RFC49LL, RFC58, RFC76)
• Temperature Rating
Cover Plate
• Model RFC
• Temperature Rating
• Finish (See Table H)
Sprinkler Wrench
• Model FC
• Model W3
v
co
co
co
co
0
N
Bulletin 006 Reliable Page 8 of 8
May 2019 www.reliablesprinkler.com
Bulletin 033 February 2019
Rellablia
Model 171 RES LL
Residential Sprinklers
Specifically Listed for use in Multipurpose Systems that serve both
domestic water and fire protection.
Types:
1. F1 Res 30 LL Pendent
2, F1 Res 30 LL Recessed Pendent/F2
3, F1 Res 30 LL Recessed Pendent/FP
4. F1 Res 49 LL Pendent
5. F1 Res 49 LL Recessed Pendent/F1
6. F1 Res 49 LL Recessed Pendent/FP
7. F1 Res 58 LL Pendent
8. F1 Res 58 LL Recessed Pendent/F1
9. F1 Res 58 LL Recessed Pendent/FP
10. F1 Res 30 LL CCP Pendent
11. F1 Res 49 LL CCP Pendent
12. F1 Res 58 LL CCP Pendent
13. F1 Res 44 LL HSW
14. F1 Res 44 LL Recessed HSW/F2
15. F1 Res 58 LL HSW
16. F1 Res 58 LL HSW Recessed HSW/F2
17. F1 Res 44 LL SWC
Pendent/F1, F1 Res 30 LL
Recessed Pendent/F2
Listings & Approvals
1. Listed by Underwriters Laboratories Inc. and
UL Certified for Canada (cULus) for Safety to ANSI/
U L 1626.
2. Certified by Underwriters Laboratories, Inc. and Under-
writers Laboratories of Canada for Health Effects to NSF/
ANSI Standard 61 Annex G (Less than 0.25% Lead Con-
tent,)
3, WaterMark certified. WaterMark Certificate Number
23347
Additional Bulletins applicable to all
F1 RES LL Sprinklers
• Wall Wetting - Bulletin 007
• Design and Installation - Bulletin 140
UL Listing Category
Residential Automatic Sprinkler
UL Guide Number
VKKW
Patents
US Patent No. 6,516,893 applies to the
Model F1 Res 49 LL & 58 LL Pendent Sprinklers
Other patents pending.
LL Recessed Pendent/FP
11
Pendent
11
CCP Pendent
HSW Recessed HSW/F2 SWC
Product Description
Model F1 Res LL Pendent sprinklers (Figs. 1, 2, 3, & 4) are
fast response sprinklers combining excellent durability, high
sensitivity glass -bulb and low profile decorative design. The
F1 Res LL Horizontal Sidewall sprinklers (Figs. 5, & 6) are
equally attractive when above ceiling piping cannot be used.
The 3mm glass -bulb pendent sprinklers permit the efficient
use of residential water supplies for sprinkler coverage in resi-
dential fire protection design.
The low flow F1 Res LL sprinklers are specially engineered
for fast thermal response to meet the sensitive fire protection
application needs of the latest residential market standards
(UL 1626 Standard). Upon fire conditions, rising heat causes
a sprinkler's heat -sensitive glass -bulb to shatter, releasing the
waterway for water flow onto the deflector, evenly distributing
the discharged water to control a fire.
Technical Data:
• Thermal Sensor: Nominal 3mm glass -bulb
• Sprinkler Frame : Brass
• Sprinklers' Pressure Rating : 175 psi
Factory Hydrostatically Tested to 500 psi
• Thread Size: 1/2" NPT (R1/2)
• K-Factor: 3.0 (Actual) - F1 Res 30 LL Pendent Sprinkler
4.9 (Actual) - F1 Res 49 LL Pendent Sprinkler
5.8 (Actual) - F1 Res 58 LL Pendent & HSW Sprinkler
4.4 (Actual) - F1 Res 44 LL HSW Sprinkler
Cj
m
0
W
co
CD
71
0
z.
Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523
Application
Model F1 Res LL sprinklers are cULus Listed in accor-
dance with UL 1626 for installation in accordance with
NFPA 13, NFPA 13R, and NFPA 13D. Sprinkler systems
using Model F1 Res LL sprinklers must be hydraulically
designed to provide at least the flow identified in the Tech-
nical Data tables in this bulletin. For NFPA 13 installations,
the flow per sprinkler must be the greater of: (1) the flow
listed in the applicable Technical Data table and (2) the
flow required to achieve a minimum design density of 0.1
gpm/sq ft over the design area of the sprinkler. For cover-
age area dimensions less than those listed in the Technical
Data tables, use the minimum required flow for the next
larger max. coverage area listed.
• Model F1 Res 30 LL, 49 LL & 58 LL Pendent
135FG03
Fig. 1
Installation
Models F1 Res LL sprinklers are to be installed as shown,
Model F1, F2 and FP Escutcheons, illustrated herewith, are
the only recessed escutcheons to be used with Model F1
Res LL sprinklers, Use of any other recessed escutcheon
will void all approvals and warranties. For installing Model
F1 Res LL Pendent sprinklers use only the Model W2 sprin-
kler Wrench; for installing Models F1 Res LL Recessed
• Model F1 Res 30 LL Recessed Pendent / F2
• Model F1 Res 49 LL & 58 LL Recessed Pendent / F1
2 1/4" HDLE DIA.
[51.2mm]
1 IS/I6" DIA.
[49.2mm]
f/
- 1"X 1/2" REDUCER
TURN COLLAR UNTIL
TIGHT AGAINST SPRINKLER
WRENCH BOSS. I I
FACE OF FITTING TO
CEILING DIMENSION:
TJT�/ 3/I6-15/16 (F1 ESCUTCHEON)
3/16-11/16 (F2 ESCUTCHEON)
ADIUSTMENT ®���
I
[3�2mmJ
A"
135FGO2A 2 27/32" Du.
[7z2mm]
Pendent, CCP & SWC sprinklers use only the Model GFR2
sprinkler wrench; for installing Model F1 LL Res Recessed
HSW sprinklers use only the Model GFR2 Sprinkler Wrench.
Use of wrenches other than those specified may damage
these sprinklers. Install F1 Res 44 LL with a ceiling to de-
flector distance of 4" - 12". Flow arrow on deflector must
point away from near wall and "Top" marking must face
ceiling.
Fig. 2
Escutcheon*, F1 or F2, Data:
Adjustment
„A„
Face of fitting
Type
Inch (mm)
Inch (mm)
to ceiling
Inch (mm)
F1
3/4 (19.0)
Min.=3/4" (19.1)
3/16 - 15/16
Max. =11/2" (38.1)
(4.7 - 24.0)
F2
1/2 (12.7)
Min.=15/16" (23.8)
3/16 - 11/16
Max. =11/2" (38.1)
(4.7 - 17.4)
* Note: Escutcheons F1 or F2 may be used with
Model F1 Res 49 LL & 58 LL Recessed Pendent Sprinkler
2.
Technical Data: F1 Res 30 LL Pendent and Recessed Pendent (SIN RA3311)
Thread
Size
Nominal Orifice
Inch mmpsi(bar)
Max. Pressure
Sprinkler Temp. Rating
Max. Ambient Temp.
Actual K
Factor
Sprinkler Length
Inch mm
OF
°C
OF
°C
1/2" NPT
21/64" (8.2)
175 (12)
155
68
100
38
3.0 (43.2)
2.25 (57)
R1/z
175
79
Max.
Ordinary Temp. Rating
Intermediate Temp. Rating
Minimum
Max. Coverage area
Spacing
155°F/68°C
175°F/79°C
Top of Deflector to Ceiling
Spacing
Flow
Pressure
Flow
Pressure
Ft x Ft (m x m)
Inch (mm)
Ft (m)
GPM (L/min)
PSI(bar)
GPM (L/min)
PSI(bar)
Ft (m)
12 x 12 (3.6 x 3.6)
12(3.6)
8(30.3)
7.0 (0.48)
8(30.3)
7.0 (0.48)
Smooth Ceilings 1" to 4"
(25mm to 100mm)
Beamed Ceilings per NFPA 13,
13D, or 13R
8(2.4)
14 x 14 (4.3 x 4.3)
14(4.3)
10 (37.8)
11 (0.76)
10 (37.8)
11 (0.76)
16 x 16 (4.9 x 4.9)
16(4.9)
13 (49)
18.8 (1.3)
13 (49)
18.8 (1.3)
Technical Data: F1 Res 49 LL Pendent and Recessed Pendent (SIN RA3316)
Thread
Nominal Orifice
Max.
Sprinkler
Max.
Actual
Sprinkler
Size
Inch (mm)
Pressure
Tem . Ratin
°F °C
Ambient Temp.
K
Length
OF
°C
psi bar
155 68
Factor
Inch mm
1/2" NPT
7/16" (11)
175 (12)
100
38
4.9 (70.6)
2.25 (57)
RYz
175 79
150
66
Ordinary Temp.
Rating
Intermediate
Temp. Rating
Top of Deflector
Minimum
Max. Coverage area
Max. Spacing
155°F/680C
175°F/790C
to Ceiling
Spacing
Flow
Pressure
Flow
Pressure
Ft x Ft (m x m)
Ft (m)
(mm)
Ft (m)
GPM min
PSI a
GPM min
PSI(bar)Inch
Smooth Ceilings 1" to 4"
(25mm to 100mm)
8(2.4)
12 x 12 (3.6 x 3.6)
12(3.6)
13 (49)
7.0 (0.48)
13 (49)
7.0 (0.48)
14 x 14 (4.3 x 4.3)
14(4.3)
13 (49)
7.0 (0.48)
13 (49)
7.0 (0.48)
16 x 16 (4.9 x 4.9)
16(4.9)
13 (49)
7.0 (0.48)
13 (49)
7.0 (0.48)
Beamed Ceilings per NFPA
13, 13D, or 13R
18 x 18 (5.5 x 5.5)
18(5.5)
17 (64.3)
12 (0.83)
17 (64.3)
12 (0.83)
20 x 20 (6.1 x 6.1)
20(6.1)
20 (75.7)
16.7 (1.14)
20 (75.7)
16.7 (114)
Max. Coverage area
Ft x Ft (m x m)
Max. Spacing
Ft (m)
Ordinary Temp. Rating
155°F/68°C(175'F/79'C)
Intermediate Temp. Rating
Top of Deflector
to
In Ceiling
(mm)
Minimum
Spacing
Ft (m)
Flow
GPM min
Pressure
PSI
Flow
GPM min
Pressure
PSI(badInch
12 x 12 (3.6 x 3.6)
12(3.6)
15 (57)
9.4 (0.65)
15 (57)
9.4 (0.65)
Smooth Ceilings 4" to 8"
(100mm to 200mm)
8(2.4)
14 x 14 (4.3 x 4.3)
14(4.3)
16 (60.5)
10.6 (0.73)
16 (60,5)
10.6 (0.73)
16 x 16 (4.9 x 4.9)
16(4.9)
17 (64.3)
12.0 (0.83)
17 (64.3)
12.0 (0.83)
18 x 18 (5.5 x 5.5)
18(5.5)
19 (72)
15.0 (1.0)
19 (72)
15.0 (1.0)
20 x 20 (6.1 x 6.1)
20(6.1)
22 (83.2)
20.2 (1.4)
22 (83.2)
20.2 (1.4)
3.
Technical Data: F1 Res 58 LL Pendent and Recessed Pendent (SIN RA3313)
Thread
Nominal Orifice
Max.
Sprinkler
Max.
Actual
Sprinkler
Size
Inch (mm)
Pressure
Temp. Ratin
Ambient Temp.
K Factor
Length
OF
°C
°F
°C
psi (bar)
Inch (mm)
1/2" NPT
1/2" (13)
175 (12)
155
68
100
38
5.8 (83.5)
2.25 (57)
(R1/2)
175
79
150
66
Ordinary Temp. Rating
Intermediate Temp. Rating
Top of Deflector
Minimum
Max. Coverage area
Max. Spacing
155°F/680C
1750F/790C
to Ceiling
Spacing
Flow
Pressure
Flow
Pressure
Ft x Ft (m x m)
Ft (m)
In (mm)
Ft (m)
GPM min
PSI a
GPM Umin
PSI(bar)Inch
12 x 12 (3.6 x 3.6)
12(3.6)
16 (61)
7.6 (0.53)
16 (61)
7.6 (0.53)
Smooth Ceilings 1" to 4"
(25mm to 100mm)
8(2.4)
14 x 14 (4.3 x 4.3)
14(4.3)
16 (61)
7.6 (0.53)
16 (61)
7.6 (0.53)
16 x 16 (4.9 x 4.9)
16(4.9)
16 (61)
7.6 (0.53)
16 (61)
7.6 (0.53)
Beamed Ceilings per NFPA 13,
13D, or 13R
18 x 18 (5.5 x 5.5)
18(5.5)
19 (72)
10.8 (0.75)
19 (72)
10.8 (0,75)
20 x 20 (6.1 x 6.1)
20(6.1)
22 (83,3)
14.4 (1.0)
22 (83.3)
14.4 (1.0)
• Model F1 Res 30 LL, 49 LL & 58
1 1 f! D 0--A-n+
2 518" [66.7mml DIA.
2 5116" DIA. HOLE IN CEILING
[58.7mm]
CUP V
1 "x1/2" REDUCER
CUP /
CEILING
1 114» [31.5mm]
WStltl MAX. FACE OF FITTING
TO FACE OF CEILING
DIMENSION
A» B'
COVER ADJUSTMENT HEIGHT
3 5116» DIA.
135FG04D [84.1 mm]
Fig. 3
• Model F1 Res 30 LL, 49 LL & 58
LL RP_CP_CCPrI PPnr1pnt / FP
rr pusn-on/tnreaa-OTT escutcneon
2 5/8" DIA. [66.7mm]
HOLE IN CEILING
2 5/16" DIA.
[58.7mm]
CUP
/
I �
1" X 1/2" REDUCER
I
1 I
I
L J
CEILING
®.iPV01
dd�� MM 99
1 1/2" [38.1mm] MAX.
FACE OF flTTING
--
-
TO FACE OF CEILING
��
DIMENSION
J_
1/2" [13mm] MAX
\
FP ADJUSTMENT
A
IJ5FG01A
Fig. 4
4
Technical Data: F1 Res 30 LL CCP Pendent and Recessed Pendent/FP (SIN RA3311)
Thread
Nominal
Max.
CCP Assembly
Max.
K
Sprinkler
Size
Orifice
Pressure
Tem . atin
Ambient Temp.
Factor
Length
°C
OF
oC
Inch mm
psi (bar)OF
Inch mm
1/2" NPT
(RI/2)
"/64" (8.2)
175 (12)
135
57
100
38
3.0 (43.2)
2.25 (57)
Max. Coverage area
Ft x Ft (m x m)
Max. Spac-
ing Ft (m)
Ordinary Temp. Rating
155°F/68°C
Top of Deflector to Ceiling
Inch (mm)
Minimum
Spacing
Ft (m)
Flow
GPM (Vmin)
Pressure
PSI bar
12 x 12 (3.6 x 3.6)
12(3.6)
8(30.3)
7.0 (0.48)
Smooth Ceilings 1/2" to 1"
(13mm to 25mm) using CCP or FP escutcheon
8(2.4)
14 x 14 (4.3 x 4.3)
14(4.3)
11 (37.8)
13.4 (0.92)
Beamed Ceilings per NFPA 13, 13D, or 13R
Technical Data: F1 Res 49 LL CCP Pendent and Recessed Pendent/FP (SIN RA3316)
Thread
Nominal
Max.
CCP Assembly
Max.
K
Sprinkler
Size
Orifice
Pressure
Temp. RatingAmbient
Temp.
Factor
Length
OF
°C
OF
oC
Inch (mm)
psi (bar)
Inch (mm)
1/2" NPT
(R'/2 )
7/16" (11)
175 (12)
135
57
100
38
4.9 (70.6)
2.25 (57)
Max. Coverage
Ordinary Temp.
Rating
Minimum
ea
Max. Spacing
(155°F/68°C)
Top of Deflector to Ceiling
Spacing
Flow
Pressure
Ft x Ftr(m x m)
Ft (m)
Inch (mm)
(m)g
12(3.6)
GPM (Vmin)
PSI (bar)
Smooth Ceilings 1/2" to 1"
(13mm to 25mm) using CCP or FP
8(2.4)
12 x 12 (3.6 x 3.6)
13 (49)
7.0 (0.48)
14 x 14 (4.3 x 4.3)
14(4.3)
13 (49)
7.0 (0.48)
16 x 16 (4.9 x 4.9)
16(4.9)
14 (53)
8.2 (0.56)
escutcheon
Beamed Ceilings per NFPA 13, 13D, or 13R
18 x 18 (5.5 x 5.5)
18(5.5)
18 (68.1)
13.5 (0.93)
20x20(6.1 x6.1)
20(6.1)
20(75.7)
16.7(1.14)
Note: Sprinklers shown in Fig. 3 and Fig. 4 are not suitable for installation in ceilings which have positive pressure in
the space above.
Technical Data: F1 Res 58 LL CCP Pendent and Recessed Pendent/FP (SIN RA3313)
Thread
Nominal
Max.
CCP Assembly
Max.
K
Sprinkler
Size
Orifice
Pressure
Temp. Ratin
Ambient Temp.
Factor
Length
OF
°C
OF
OC
Inch (mm)
psi (bar)
Inch (mm)
1/2" NPT
(R'/2 )
1/2" (13)
175 (12)
135
57
100
38
5.8 (83.5)
2.25 (57)
Max. Coverage
Ordinary Temp. Rating
Minimum
area
Max. Spacing
(155°F/68°C)
Top of Deflector to Ceiling
Spacing
Flow
Pressure
Ft x Ft (m x m)
Ft (m)
Inch (mm)
(m)
GPM (Vmin
PSI(bar)Ft
12 x 12 (3.6 x 3.6)
12(3.6)
16 (61)
7.6 (0.53)
14 x 14 (4.3 x 4.3)
14(4.3)
16(61)
7.6(0.53)
Smooth Ceilings 1/2" to 1"
16 x 16 (4.9 x 4.9)
16(4.9)
16 (61)
7.6 (0.53)
(13mm to 25mm) using CCP or FP escutcheon
Beamed Ceilings per NFPA 13, 13D, or 13R
8(2.4)
18 x 18 (5.5 x 5.5)
18(5.5)
19 (72)
10.8 (0.75)
20 x 20 (6.1 x 6.1)
20(6.1)
22 (83.3)
14.4 (1.0)
5.
rll�"� 1
FACE OF FITTING TO
WALL DIMENSION
1 1/4 ` MIN.
[31.8mm]
2 1/4" HOLE DIA.
1/8 'q"
[57.2mm]
CEILING TO
[3.2mm]
DEFLECTOR
1" X 1/2- REDUCER
DIMENSION
ro�
Illi lip I �--r1
��
IIIIIIII
1 15/16" DIA.
[49.2mm] hill
IIIII
2 27/32" DIA.
IIIII
[72.2mm]
_IlIV
V
TURN COLLAR UNTIL
TIGHT AGAINST SPRINKLER
WRENCH BOSS.
l�
`\
1/2- [13mm]
IJ5FG06-D
ADJUSTMENT
• Model F1 Res 44 LL & 58 LL HSW
(r _
� .' �. ice►
Rom, � •�,,
1
• Model F1 Res 44 LL & 58 LL Recessed HSW/F2
escutcheon, 1 2" (13mm) adjustment
Technical Data: F1 Res 44 LL HSW & HSW/F2 (SIN RA3331)
Nominal
Max.
Sprinkler
Max.
Sprinkler
Thread
Orifice
Pressure
Temp. Rating
Ambient
K
Length
Size
Inch (mm)
psi (bar)
Temp.
Factor
Inch (mm)
of
°C
1/2" NPT
3/8" (10)
175 (12)
155
68
100
38
4.4(63)
2.45 (62)
(R/2)
175
79
150
66
Escutcheon. F2. Data:
Face of
T
Type
Adjustment
to wetting
ll
Inch (mm)
Inch (mm)
F2
1/2 (1 3)
3/16 - 11/16
(4.7 - 17.4)
Max. Coverage area
Ft x Ft (m x m)
Max. Spac-
ing Ft (m)
Ordinary Temp. Rating
(155°F/68°C)
Intermediate
(175°F/79°C)
Temp. Rating
Top of Deflector to
Ceiling
Inch (mm)
4 to 6 (100 to 152)
Minimum
Spacing
Ft (m)
8(2.4)
Flow Pressure
GPM (L/min) PSI (bar)
Flow
GPM (Umin)
Pressure
PSI (bar)
12 x 12 (3.6 x 3.6)
12(3.6)
12 (45.4)
7.5 (0.52)
12 (45.4)
7.5 (0.52)
14 x 14 (4.3 x 4.3)
14(4.3)
14 (53.0)
10.2 (0.71)
14 (53.0)
10.2 (0.71)
16 x 16 (4.9 x 4,9)
16(4.9)
16 (60.6)
13.3 (0.92)
16 (60.6)
13.3 (0.92)
16 x 18 (4.9 x 5.5)
16(4.9)
18 (68.1)
16.8 (0.53)
18 (68.1)
16.8 (0.53)
18 x 18 (5.5 x 5.5)
18(5.5)
19 (72.0)
18.7 (1.29)
19 (72.0)
18.7 (1.29)
16 x 20 (4.9 x 6.1)
16(4.9)
23 (87.1)
27.4 (1.89)
23 (87.1)
27.4 (1.89)
12 x 12 (3.6 x 3.6)
12(3.6)
14 (53.0)
10.2 (0.71)
14 (53.0)
10.2 (0.71)
6 to 12 (152 to 305)
14 x 14 (4.3 x 4.3)
14(4.3)
16 (60.6)
13.3 (0.92)
16 (60.6)
13.3 (0.92)
16 x 16 (4.9 x 4.9)
16(4.9)
17 (64.4)
15.0 (1.04)
17 (64.4)
15.0 (1.04)
16 x 18 (4.9 x 5.5)
16(4.9)
20 (75.7)
20.7 (1.43)
20 (75.7)
20.7 (1.43)
16 x 20 (4.9 x 6.1)
16(4.9)
23 (87.1)
27.4 (1.89)
23 (87.1)
27.4 (1.89)
on
Technical Data: F1 Res 58 LL HSW & HSW/F2 (SIN RA3333)
Thread
Nominal
Max.
Sprinkler
Max.
Ambient
K
Sprinkler
Size
Orifice
Pressure
Temp. Rating
Temp.
Factor
Length
Inch (mm)
psi (bar)
Inch (mm)
OF
°C
°F
°C
1/2" NPT
1/2" (13)
175 (12)
155
68
100
38
5.8 (83.5)
2.45 (62)
(R1/2)
175
79
150
66
Max. Coverage area
Ft x Ft (m x m)
12 x 12 (3.6 x 3.6)
Max. Spacing
Ft (m)
Ordinary Temp.
155°F/68°C
Rating
Intermediate
1750F/79°C
Temp. Rating
Top of Deflector to
Ceiling
Inch (mm)
Minimum
Spacing
Ft (m)
Flow
GPM min)VPSI(bar)--GPM
Pressure
Flow
Vmin
Pressure
PSI ar
12(3.6)
16 (60.6)
7.6 (0.53)
16 (60.6)
7.6 (0.53)
4 to 6 (100 to 152)
8(2.4)
14 x 14 (4.3 x 4.3)
14(4.3)
18 (68.2)
9.7 (0.69)
18 (68.2)
9.7 (0.69)
16 x 16 (4.9 x 4.9)
16(4.9)
21 (79.5)
13.2 (0.91)
21 (79.5)
13.2 (0.91)
16 x 18 (4.9 x 5.5)
16(4.9)
25 (94.7)
18.6 (1.28)
25 (94.7)
18.6 (1.28)
16 x 20 (4.9 x 6.1)
16(4.9)
29 (109.8)
25.0 (1.73)
29 (109.8)
25.0 (1.73)
12 x 12 (3.6 x 3.6)
12(3.6)
22 (83.3)
14.4 (1.0)
22 (83.3)
14.4 (1.0)
6 to 12 (152 to 305)
14 x 14 (4.3 x 4.3)
14(4.3)
22 (83.3)
14.4 (1.0)
22 (83.3)
14.4 (1.0)
16 x 16 (4.9 x 4.9)
16(4.9)
26 (98.4)
20.1 (1.39)
26 (98.4)
20.1 (1.39)
16 x 18 (4.9 x 5.5)
16(4.9)
31 (117.4)
28.6 (1.97)
31 (117.4)
28.6 (1.97)
• Model F1 Res 44 LL SWC
Technical Data: F1 Res 44 LL SWC SIN RA3331
4" to 12"
[101.60mm To
304.80mm]
1
1/4" [31.75mm] Maximum
Face Of Fitting
To Wall Dimension
PUSH ON COVER, THEN
TURN TO ADJUST UNTIL
TIGHT AGAINST WALL.
I" X 1/2" Reducer
id
Recommended
Well Hole
2 5/8"
2 5/16"
[58.74mm]�-tiii - -
-
-
--
[66.68mm]
Dig.
3 5/16"
Dig.
L ignL-r-
, [84.14mm]
_
/ Dio.
--
TURN COLLAR UNTIL
TIGHT AGAINST SPRINKLER
1 21/32
WRENCH BOSS.
[42. 07mm]
IJ5FG07
1/2" [12.70mm]
Adjustment
Fig. 6
Nominal
Max.
Cover
Max.
Sprinkler
Thread
Orifice
Pressure
Temp.
Ambient
K
Length
Size
inch (mm)
psi (bar)
Rating
Temp.
Factor
Inch (mm)
OF
°C
OF
°C
1/2" NPT
(R1/2)
a „
/s (10)
175 (12)
135
57
100
38
4.4(63)
2.45 (62)
7.
Technical Data: F1 Res 44 LL SWC (SIN RA3331) continued
Max. Coverage area
Ft x Ft (m x m)
Max. Spacing
Ft (m)
Ordinary Temp. Rating
155°F/68°C
Top of Deflector to
Ceiling
Inch (mm)
Minimum
Spacing
Ft (m)
Flow
GPM (Vmin)
Pressure
PSI bar
12 x 12 (3.6 x 3.6)
12(3.6)
13 (49.2)
8.7 (0.60)
4 to 6 (100 to 152)
8(2.4)
14 x 14 (4.3 x 4.3)
14(4.3)
14 (53.0)
10.2 (0.71)
16 x 16 (4.9 x 4.9)
16(4.9)
17(64.3)
15.0(1.1)
16 x 18 (4.9 x 5.5)
16(4.9)
19 (71.8)
18.7 (1.13)
16 x 20 (4.9 x 6.1)
16(4.9)
23 (87.1)
27.4 (1.89)
12 x 12 (3.6 x 3.6)
12(3.6)
14 (52.9)
10.2 (0.71)
6 to 12 (152 to 305)
14 x 14 (4.3 x 4.3)
14(4.3)
15 (56.7)
11.7 (0.81)
16 x 16 (4.9 x 4.9)
16(4.9)
18(68.1)
16.8(1.16)
16 x 18 (4.9 x 5.5)
16(4.9)
20 (75.6)
20.7 (1.43)
Maintenance
Model F1 Res 30 LL, 49 LL, F1 Res 58 LL and F1 Res 44
LL Sprinklers should be inspected and the sprinkler sys-
tem maintained in accordance with NFPA 25, 13, 13D, and
13R. Do not clean sprinkler with soap and water, Ammonia
or any other cleaning fluids. Remove dust by using a soft
brush or gentle vacuuming. Replace any sprinkler which
has been painted (other than factory applied) or damaged
in any way. A stock of spare sprinklers should be main-
tained to allow quick replacement of damaged or operated
sprinklers. Prior to installation, sprinklers should remain
in the original cartons and packaging until used. This will
minimize the potential for damage to sprinklers that could
cause improper operation or non -operation.
Model F1 Res 30 LL, 49 LL & 58 LL Pendent
Sprinkler Specifications
Sprinklers shall be [cULus Listed] [WaterMark Certified
WMCS] low flow residential pendent sprinklers engineered
to provide a minimum design density of 0.05 gpm/ft2 over
the listed coverage area. Listed flows as specified by the
manufacturer's technical data sheets are to be used. Resi-
dential sprinklers shall be installed in conformance with the
manufacturer's installation guidelines and the applicable
installation standard. Deflector -to -ceiling distance listing
shall be 1" to 4" maximum, unless specifically listed other-
wise. Sprinkler frame and deflector shall be of bronze frame
construction having a'/2" NPT thread. Water seal assembly
shall consist of a PTFE-coated Belleville spring washer with
top -loaded extruded or cold head cup with 3 mm glass
bulb containing no plastic parts, and having a temperature
rating of [155°F (68°C)] [175°F (79°C)]. Sprinklers shall
have a nominal K-factor of 3.0, 4.9 and 5.8. Standard fin-
ish; [Bronze] [Chrome -plated] [White Polyester] [Special
finish- specify]. Residential pendent sprinklers shall be
Reliable Model F1 Res 30 LL, 49 LL & 58 LL, SIN RA3311,
RA3316 & RA3313 (Bulletin 033).
Model F1 Res 49 LL & 58 LL Recessed
Pendent/F1
Model F1 Res 30 LL, 49 LL & 58 LL Recessed
Pendent/F2
Model F1 Res 30 LL, 49 LL & 58 LL Recessed
Pendent/FP Specifications
Sprinklers shall be [cULus Listed] [WaterMark Certified
WMCS] low flow residential recessed pendent sprinklers
engineered to provide a minimum design density of 0.05
gpm/ft2 over the listed coverage area. Listed flows as
specified by the manufacturer's technical data sheets are
to be used. Residential sprinklers shall be installed in con-
formance with the manufacturer's installation guidelines
and the applicable installation standard. Deflector -to -ceil-
ing distance listing shall be 1" to 4" maximum, unless spe-
cifically listed otherwise. Sprinkler frame and deflector shall
be of bronze frame construction having a'/2" NPT thread.
Water seal assembly shall consist of a PTFE-coated Bel-
leville spring washer with top -loaded extruded or cold
head cup with 3 mm glass bulb containing no plastic parts,
and having a temperature rating of [155°F (68°C)] [175°F
(79°C)], Sprinklers shall have a nominal K-factor of 3.0, 4.9
& 5.8. Standard finish; [Bronze] [Chrome -plated] [White
Polyester] [Special finish- specify]. Recessed escutcheon
assembly shall be a steel, two-piece escutcheon [with'/2"
adjustment (Model F2)] [with 3/4" adjustment (Model F1)] [of
push -on and thread off design with'/2" adjustment (Model
FP)]. Standard finish shall be [brass][bright chrome] [white
painted]. Residential recessed pendent sprinklers shall be
Reliable [Model F1 Res 30 LL, 49 LL & 58 LL Recessed
Pendent/F1 ] [Model F1 Res 30 LL, 49 LL & 58 LL Recessed
Pendent/F2] [Model F1 Res 30 LL, 49 LL & 58 LL Recessed
Pendent/FP] SIN RA3311, RA3316 & RA3313 (Bulletin 033),
A.,
Model F1 Res 30 LL, 49 LL & 58 LL CCP Pendent
(Concealed) Specifications
Sprinklers shall be [cULus Listed] [WaterMark Certified
WMCS] low flow residential concealed sprinklers engi-
neered to provide a minimum design density of 0.05 gpm/
ft2 over the listed coverage area. Listed flows as speci-
fied by the manufacturer's technical data sheets are to be
used. Residential sprinklers shall be installed in confor-
mance with the manufacturer's installation guidelines and
the applicable installation standard. Sprinkler frame and
deflector shall be of bronze frame construction having a 1/2"
NPT thread. Water seal assembly shall consist of a PTFE-
coated Belleville spring washer with top -loaded extruded
or cold head cup with 3 mm glass bulb containing no plas-
tic parts, and having a temperature rating of 1550F (680C).
Cover plate assembly shall consist of a brass cover plate
and copper alloy retainer flange. Method of attaching the
cover plate to the sprinkler cup shall be a push -on and
thread -off design allowing a 1/2" cover plate adjustment.
Cover plate temperature rating shall be 135°F (57°C), A
plastic protective cap shall be provided and factory in-
stalled inside the sprinkler cup to protect the sprinkler from
damage, which could occur during construction before the
cover plate is installed, Standard cover plate finish: [White]
[Custom Color— specify]. ]. Concealed pendent sprinklers
shall be Reliable Model F1 Res 30 LL, 49 LL & 58 LL CCP,
SIN RA3311, RA3316 & RA3313 (Bulletin 033).
Model F1 Res 44 LL Horizontal Sidewall
Residential Sprinkler Specifications
Sprinklers shall be [cULus Listed] [WaterMark Certified
WMCS] low flow residential horizontal sidewall sprinklers
engineered to provide a minimum design density of 0.05
gpm/ft2 over the listed coverage area. Listed flows as
specified by the manufacturer's technical data sheets are to
be used. Residential sprinklers shall be installed in confor-
mance with the manufacturer's installation guidelines and
the applicable installation standard. Sprinkler frame and
deflector shall be of bronze frame construction having a 1/2"
NPT thread. Water seal assembly shall consist of a PTFE-
coated Belleville spring washer with top -loaded extruded
or cold head cup with 3 mm glass bulb containing no plas-
tic parts, and having a temperature rating of [ 1550F (680C)]
[175°F (790C)], Sprinklers shall have a nominal K-factor
of 4.4 (62,8). Standard finish: [Bronze] [Chrome -plated]
[White Polyester] [Special finish— specify]. Residential hori-
zontal sidewall sprinklers shall be Reliable Model F1 Res
44 LL, SIN RA3331 (Bulletin 033).
Model F1 Res 44 LL Recessed
Horizontal Sidewall Sprinkler Specifications
Use description for the Model F1 Res 44 horizontal side -
wall sprinkler with the following modifications: Replace
"horizontal sidewall sprinkler" with "recessed horizontal
sprinkler." Add: Recessed escutcheon assembly shall be
a steel, two-piece escutcheon with 1/2" adjustment (Model
F2). Standard finish shall be [brass][bright chrome] [white
painted] [Special finish— specify]. Residential recessed
horizontal sidewall sprinklers shall be Reliable Model F1
Res 44 LL/F2, SIN RA3331 (Bulletin 033).
Standard Finishes
F1, F2, FP
Sprinkler
Cover Plates
Escutcheons
Bronze
Brass
White Painted
Chrome Plated
Bright Chrome Plated
Chrome
White and Black Polyester
White Painted
Coated
Special Application Finishes
F1, F2,
Sprinkler
Cover Plates
Escutcheons
Bright Brass
Bright Brass
Bright Brass
Black Plated
Black Plated
Black Plated
Black Paint
Black Paint
Black Paint
Off White
Off White
Off White
Satin Chrome
Satin Chrome
Satin Chrome
(1) Other finishes and colors are available on special order.
Consult factory for details.
Note: Paint or any other coating applied over the factory finish will void
all approvals and warranties.
Ordering Information
Specify:
1. Sprinkler Model
2. Sprinkler Type
3. Temperature Rating
4. Sprinkler Finish
5. Escutcheon Finish
6. Cover Plate Finish
The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory
Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for almost 100 years.
Manufactured by
Reliable Automatic Sprinkler Co., Inc. J011111 Recycled
® (800) 431-1588 Sales Offices Paper
Relle labi
(800) 848-6051 Sales Fax Revision lines indicate updated or new data.
(914) 829-2042 Corporate Offices
www.reliablesprinkler.com Internet Address EG. Printed in U.S.A. 02/19 P/N 9999970411
Bulletin 157 September 2019
Features
1. Available in the following configurations:
• Pendent with standard escutcheon
• Pendent with Model HB extended escutcheon
• Pendent with Model FP recessed escutcheon
• Pendent with Model F1 recessed escutcheon
• Concealed Pendent with Model CCP cover plate
• Horizontal Sidewall with Standard escutcheon
• Horizontal Sidewall with Model HB extended es-
cutcheon
• Horizontal Sidewall with Model FP recessed es-
cutcheon (FM Standard Response)
• Horizontal Sidewall with Model F1 recessed es-
cutcheon (FM Standard Response)
• Upright
2. Available with 1" NPT, ISO7-1R1, 3/4" NPT, or IS07-
1 R3/4 inlet fitting.
3. 3/4" NPT inlet fittings permit replacement of older 3/4"
inlet dry sprinklers without changing to a larger sprin-
kler fitting.
4. Sprinklers, escutcheons, and cover plates are avail-
able in a wide variety of standard and special appli-
cation finishes.
5. White polyester, black polyester, and Electroless
Nickel PTFE (ENT) finish sprinklers are cULus Listed
as Corrosion Resistant.
6. Available with cULus Listed 250 psi (17.2 bar) pres-
sure rating for Dry Pendent and select HSW configu-
rations. FM Approved for 175 psi (12 bar).
Product Description
Model F3QR56 Dry sprinklers are quick -response, stan-
dard coverage sprinklers with a nominal K-Factor of 5.6 (80
metric). Available in Dry Pendent, Dry Horizontal Sidewall,
and Dry Upright configurations, Model F3QR56 Dry sprin-
klers all use a 3 mm glass bulb operating element. See the
Temperature Ratings table in this Bulletin for available tem-
perature ratings. Model F3QR56 Dry sprinklers are intended
for installation on wet -pipe, dry -pipe, or preaction sprinkler
systems in accordance with NFPA 13, FM Property Loss
Prevention Data Sheets, and other applicable installation
standards.
Model F3QR56 Dry Pendent and Sidewall sprinklers are
available with a variety of escutcheon options as illustrated
in Figs. 1 through 3 and Figs. 5 through 9. In addition, Model
F3QR56 Dry Pendent sprinklers are also available with the
Model CCP conical concealed cover plate as illustrated in
Fig. 4. Available sprinkler, escutcheon, and cover plate fin-
ishes are identified in the Finishes table in this Bulletin. The
Model F1 escutcheon, Model FP escutcheon, and Model
CCP cover plate are the only recessed escutcheons and
cover plate listed for use with Model F3QR56 Dry sprinklers;
the use of any other recessed escutcheon or cover plate
Model F3QR56 Dry
K5.6 (80 metric)
Quick -Response,
Standard Spray Sprinklers
(See Fig. 1)
(See Fig. 3)
Recessed F1 Pendent
(See Fig. 5)
Horizontal Sidewall / HB
(See Fig. 7)
Recessed F1
Horizontal Sidewall
(See Fig. 9)
r�
r ^
Pendent / HB
(See Fig. 2)
REPO
Concealed
(See Fig. 4)
Horizontal Sidewall
(See Fig. 6)
t
Recessed FP
Horizontal Sidewall
(See Fig. 8)
Upright
(See Fig. 10)
z.
Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523
with Model F3QR56 Dry sprinklers will void all guarantees,
warranties, listings and approvals.
Inlet fittings are available with 1" NPT, ISO 7-1 R1, 3/4" NPT,
or IS07-1 R3/4 threads. Sprinklers with 3/4" NPT and IS07-
1 R3/4 inlet fittings are intended primarily for replacement of
existing 3/4" or IS07-1 R3/4 inlet dry sprinklers, but may also
be used in new installations.
See the Available Configurations, Listings, and Approvals
table in this Bulletin for further information on Model F3QR56
Dry sprinklers.
Available Configurations, Listings, and Approvals
Available
Sprinkler
Sprinkler
Escutcheon or
Listings and
Inlet
Identification
Model
Cover Plate
Length
Approvals(')
Threads
Number
(See Figs. 1-9)
(SIN)
Standard
2" to 36"
Escutcheon
(50 to 900 mm)
HB Extended
Escutcheon
cULus, NYC
3/4" NPT or
F1 Recessed
Escutcheon
3-1/2" to 36"
IS07-1 R3/4
(90 to 900 mm)
FP Recessed
Escutcheon
CCP Cover Plate
F3QR56 Dry
Pendent
Standard
2" to 48"
R5714
Escutcheon
(50 to 1200 mm)
HB Extended
Escutcheon
1" NPT
F1 Recessed
cULus, FM, NYC
or
Escutcheon
Escutcheon
3-1/2" to 48"
R1
(90 to 1200 mm)
FP Recessed
Escutcheon
CCP Cover Plate
Standard
2" to 48"
Escutcheon
(50 to 1200 mm)
HB Extended
Escutcheon
cULus(2), NYC(2)
3/4" NPT
3-1/2" to 48"
or
IS07-1 R3/4
F1 Recessed
Escutcheon
(90 to 1200 mm)
FP Recessed
F
F3QR56 Dry
Escutcheon
Horizontal
Sidewall
Standard
2" to 48"
cULus (2�
R5734
Escutcheon
(50 to 1200 mm)
,
FM(3), NYC(2)
HB Extended
3-1/2" to 48"
Escutcheon
(90 to 1200 mm)or
1" NPT
7-1 R1
IS07-
F1 Recessed
Escutcheon
3-1/2" to 48"
cULus(2),
FP Recessed
(90 to 1200 mm)
FM(3)(4), NYC(2)
Escutcheon
F3QR56 Dry
N/A
5" to 48"
cULus(2)
1" NPT or
R5724
Upright
(127 to 1200 mm)
IS07-1 R1
(') For available temperature ratings and finishes see the Temperature Ratings and Finishes tables, respectively, in this Bulletin.
(2) cULus Listing and NYC for Light Hazard and Ordinary Hazard only.
(3) FM Approved for Light Hazard only.
(4) Model F3QR56 Dry Horizontal Sidewall with Model F1 or Model FP recessed escutcheon are FM Approved as Standard Response.
2.
Patents
Model F3QR56 Dry series sprinklers may be covered by one or more of the following patents;
US Patent No. 5,775,431
US Patent No. 5,967,240
Listing and Approval Agencies
See the Available Configurations, Listings, and Approvals table in this Bulletin for listings and approvals applicable to
each available configuration.
1. Listed by Underwriters Laboratories, Inc. and UL Certified for Canada (cULus)
2, Certified by FM Approvals (FM)
3, Permitted in New York City based on UL Listing per Local Law 33/2007 (NYC)
Technical Data
Nominal K-Factor; 5.6 gpm/psi"2 (80 L/min/bar'12)
Sprinkler
Listing or Approval
Deflector to Ceiling Distance
Maximum Working Pressure
F3QR56 Dry
Pendent
cULus, NYC
See note below
250 psi (17.2 bar)
FM
See note below
175 psi (12 bar)
F3QR56 Dry
Horizontal Sidewall
cULus, NYC
4" to 6 "
250 psi (17.2 bar)
4" to 12"
175 psi (12 bar)
FM
See note below
175 psi (12 bar)
F3QR56 Dry Upright
cULus
See note below
175 psi (12 bar)
Note: Deflector distance to be in accordance with applicable NFPA, FM, or other agency requirements. Information is
provided only when additional clarification necessary.
Temperature
Classification
Glass Bulb Color
Sprinkler
Temperature Rating
Cover Plate
Temperature Rating
Maximum Ceil-
ing Temperature
Listings and
Approvals(')
Ordinary
Orange
135°F(57°C)
135°F (57°C)
100°F (38°C)
cULus, FM, NYC
Red
155 ° F ( 68 °C)
Intermediate
Yellow
175°F (79°C)
165°F (74°C)
150°F (66°C)
cULus, NYC
Intermediate
I Green
200°F (93°C)
165°F (74°C)
150°F (66°C)
cULus, FM, NYC
High
Blue
286°F (141°C)
None
225°F (107°C)
cULus, FMM, NYC
165°F (74°C)
150°F (66°C)
cULus, NYC
(') For listed and approved sprinkler, escutcheon, and inlet configurations see the Available Configurations, Listings, and Approvals table in this Bulletin.
(2) High temperature classification is FM Approved with Standard and Model HB escutcheons only.
FinisheS4
Component
Sprinkler
Escutcheon')
Cover Plate
Bronze
Brass(')
White Paint
White Polyester (2)
White Polyester
Standard Finishes
Chrome
Chrome
Chrome
Electroless Nickel PTFE(2)
Electroless Nickel PTFE
Satin Chrome
Black Polyester (2)
Special Application Finishes
Black Polyester
Black Paint
Custom Color Paint
Custom Color Polyester
Customer Color Polyester
Black Plating
(') Standard and Model HB escutcheons are supplied with both the can and escutcheon finished. Model F1 escutcheons are supplied with both the collar
and escutcheon finished. Model FP escutcheons are supplied with the escutcheon finished; the cup is galvanized steel with no further finish.
(2) cULus Listed as a Corrosion Resistant Sprinkler.
(3) Brass finish available for standard, Model F1, and Model FP escutcheons only.
(4) Dry upright sprinkler available in standard bronze only.
3.
Model F3QR56 Dry Pendent Sprinkler with Standard Escutcheon (SIN R5714)
Dim. 2" to 48" (51mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
2" to 36" (51mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
"A" Dimension [5z
Hole
11 /4"
[32 mm]
Escutcheon
Adjustment
Nominal Escutcheon Position
1/4" [6 mm]
Escutcheon Adjustment
1/4" [6 mr
Nominal PI atrUS1-1 1
Fig. 1
3"
[76 mm]
DIA.
m Fitting
-itting
:r Can
ion
15/32"
[12mm]
8"
m]
COMDRYDET1
Note: The sprinkler can protrudes 1/4" when escutcheon is in nominal position. Escutcheon adjustment provides -1/4" (-6mm) to +11/4" (+32mm) "A"
dimension adjustment range.
Sprinkler Guard: Model C2
9
Model F3QR56 Dry Pendent Sprinkler with Model HB Extended Escutcheon (SIN R5714)
Dim. 31/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
31/2" to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
i
"A" Dimension 2-1/2" [64 mm]
Dia. Hole in Ceiling
i
1/2" [13mm]
Escutcheon Adjustment
T 1-1/4"
[32mm]
Norlinal Position
of Escutcheon
1/2" [13mm]
Escutcheon Adjustment
COMDRYDET2
Fig. 2
3-1 /2"
[89 mm]
Escutcheon
Dia.
System tee
Inlet fitting
Ceiling
Escutcheon
Sprinkler Can
Note: The sprinkler can protrudes 11/4" when escutcheon is in nominal position. Escutcheon adjustment provides '/2" (-12.7mm) to +1/2" (+12.7mm)
"A" dimension adjustment range.
Sprinkler Guard: Model C2
5.
Model F3QR56 Dry Pendent Sprinkler with Model FP Recessed Escutcheon (SIN R5714)
Dim. 31/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
31/2" to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
"A" Dimension
rz----- -
--I--A�
r
System Tee
Hole in Ceiling
1/4" [6 mm]
Escutcheon Adjustment
1 Ceiling
i Inlet Fitting
Sprinkler
Cup
Escutcheon
f3/4" [19 mm] Nom.
Nominal
Escutcheon Position 3-7/32"
1/4" [6 mm]
Escutcheon Adjustment [82 mm] Dia.
COMDRYDET3
Fig. 3
Note: Do not install the Model F3QR56 Dry Pendent sprinkler with the Model FP escutcheon in ceilings which have positive pressure in the space
above.
91
Model F3QR56 Dry Pendent Sprinkler with Model CCP Cover Plate (SIN R5714)
"A" Dim. 31/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
31/z" to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
----�-- I--------r--��11----f i
4__� _►-
System Tee
_ .,_ -._.
"A" Dimension Hole in Ceiling
3/16" [5 mm]
Cover Plate Adjustment
1 Ceiling
I
Nominal Cover
Plate Position
3/16" [5 mm]
Cover Plate Adjustment
Fig. 4
i
3-5/16"
[84 mm] Dia.
Inlet Fitting
Sprinkler Cup
Model CCP 1/2
Cover Plate Assembly
7/8"
4���r[22 mm]
COMDRYDET4
Note: Do not install the Model F3QR56 Dry Pendent sprinkler with the Model CCP cover plate in ceilings which have positive pressure in the space
above.
7.
Model F3QR56 Dry Pendent Sprinkler with Model F1 Recessed Escutcheon (SIN R5714)
"A" Dim. 31/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
31/2" to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections.
2-1/4" [57 mm] Dia.
Hole in Ceiling
"A" Dimension
F z
L_
---I�r�-- -7`
I PIII i
iiil I
- System Tee
Inlet Fitting
Collar
1/4" [6 mm]
Escutcheon Adjustment
1 /8
Ceiling ,�[3 mm]
Nominal Escutcheon
Position Escutcheon
1/4" [6 mm]
Escutcheon Adjustment
2-27/32" _
[72 mm] Dia.
COMDRYDET5
Fig. 5
91
Model F30R56 Dry Horizontal Sidewall Sprinkler with Standard Escutcheon (SIN R5734)
"A" Dim. 2 to 48" (51mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
2" to 36" (51mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
System Fitting
COMDRYDET6
Sprinkler Can
Inlet Fitting
2-1/8"
[54 mm] Dia.
Hole in Wall
1-1/4" [32 mm]
Escutcheon Adjustment
"A" Dimension
Tor Ceiling
4 [102 mm] Min.
12" [305 mm] Max.
15/32" [12mm]
2-3/32"
[53 mm] i
5/8" [16 mm]
-- --- [76 mm]
Fig. 6
1/4" [6mm] Nominal Protrusion
1/4" [6 mm]
Escutcheon Adjustment
Nominal Escutcheon Position
Note: The sprinkler can protrudes 1/a" when escutcheon is in nominal position. Escutcheon adjustment provides '/a" (-6mm) to +11/4" (+32mm) "A"
dimension adjustment range.
91
Model F301356 Dry Horizontal Sidewall Sprinkler with Model HB Escutcheon (SIN R5734)
"A" Dim. 3'/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
3/2" to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
System Tee
Inlet Fitting
Ceiling
� I
4" [102mm] Min.
Escutcheon
Sprinkler Can
2 3/32"
[53mm]
12" [305mm] Max.
1
5/8" [16mm]
Escutcheon
eonDia.
T 1
2 1/2" Dia. t
Hole in Wall 1-1/4" 1-1/4" [32mm] Nominal Protrusion
[32mm]
1/2" [13mm]
Escutcheon Adjustment
COMDRYDET7 1/2" [13mm] Nominal Position
Escutcheon of Escutcheon
Adjustment
"A" Dimension —
Fig. 7
Note: The sprinkler can protrudes 11/4" when escutcheon is in nominal position. Escutcheon adjustment provides 1/2" (-12.7mm) to +1/2" (+12.7mm)
"A" dimension adjustment range.
10.
Model F3QR56 Dry Horizontal Sidewall Sprinkler with Model FP Recessed Escutcheon (SIN R5734)
"A" Dim. 31/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
31/2' to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
Ceiling
Nom.
1-1/4"
Escutcheon [32 mm]
4" [102 mm] Min.
Sprinkler Cup cULus, NYC: 6" [152 mm] Max,
System Tee FM: 12" [305 mm] Max.
Inlet Fitting
5/8" [16 mm]
3-7/32"
[82 mm] Dia.
2-1/2"
[64 mm] Dia.
Hole in Wall
COMDRYDET8
1/4" [6 mm]
Escutcheon Adjustment
"A" Dimension
•
1/4" [6 mm]
Escutcheon Adjustment
Nominal Escutcheon Position
Note: Do not install the Model F3QR56 Dry Horizontal Sidewall sprinkler with the Model FP escutcheon in walls which are positively pressurized with
respect to the protected space.
11.
Model F301356 Dry Horizontal Sidewall Sprinkler with Model F1 Recessed Escutcheon (SIN R5734)
3'/2" to 48" (89mm to 1219mm) in 1/4" (6mm) increments for 1" connections or
31/2" to 36" (89mm to 914mm) in 1/4" (6mm) increments for 3/4" connections
System Tee
_sue
COMDRYDET9
Escutcheon
Collar
/— Inlet Fitting
2-1/4" [57 mm] Dia.
Hole in Wall
1/4" [6 mm]
Escutcheon Adjustment
"A" Dimension
Fig. 9
Nom.
1-3/4"
1/8" [44 mm]
[3 mm] 4" [102 mm] Min.
cULus, NYC: 6" [152 mm] Max.
FM: 12" [305 mm] Max.
5/8" [16 mm]
2-27/32"
[72 mm] Dia.
1/4" [6 mm]
Escutcheon Adjustment
Nominal Position
of Escutcheon
12.
Model F3QR56 Dry Upright (SIN 5724)
Order Dimensions 5" to 48" (127 mm to 1219 mm)
Note: Customer is responsible
for determining correct
deflector distance below
structure above.
Order
Dimension
Inlet Fitting
System Tee - -
COMDRYDET10
J J— _,
j7�1
I �i�i�il I I i�i�i II II
I \�
Fig. 10
13.
MINIMUM EXPOSED BARREL LENGTH WHEN CONNECTED TO WET PIPE SPRINKLER SYSTEM
NOTE: STANDARD DRY PENDENT IS SHOWN, HOWEVER, MINIMUM EXPOSED BARREL LENGTH
APPLIES TO ALL STYLES OF DRY SPRINKLERS CONNECTED TO A WET PIPE SYSTEM.
WET PIPE
AMBIENT
TEMPERATURE
EXPOSED TO
DISCHARGE END
OF SPRINKLER#(F
EXPOSED BARREL
AMBIENT TEMPERATURE
40'F/4'C I 50F/10'C 60'F/16'C
EXPOSED MINIMUM BARREL LENGTH"
CE OF FITTING TO TOP OF CEILING)=
IN. (MM) IN. (MM) IN. (MM)
40-F (4'C)
0
0
0
30-F (-I Q)
0
0
0
20-F (-7°C)
4 (100)
0
0
107 (-12'C)
8 (200)
1 (25)
0
07 (-18'C)
12 (300)
3 (75)
0
-107 (-23'C)
14 (350)
4 (100)
1 (25)
-207 (-29'C)
14 (350)
6 (150)
3 (75)
-307 (-34'C)
16 (400)
8 (200)
4 (100)
-40'F (-40'C)
18 (450)
8 (200)
4 (0)
F
20 (500)
10 (250)
6 (150)10
-607 (-51'C)
20 (500)
10 (250)
6 (150)
. FOR AMBIENT TEMPERATURES EXPOSED TO THE DISCHARGE
END OF THE SPRINKLER THAT OCCUR BETWEEN THE VALUES
LISTED, USE THE NEXT COOLER TEMPERATURE.
" THE MINIMUM EXPOSED BARREL LENGTH IS NOT THE SAME
AS THE "A" DIMENSION. THE MINIMUM EXPOSED BARREL
LENGTH IS BASED ON A PROPERLY SEALED PENETRATION WITH
A MAXIMUM WIND VELOCITY ON THE EXPOSED SPRINKLER OF
30 MPH (48 KM/H). LONGER EXPOSED BARREL LENGTHS WILL
HELP AVOID FREEZING OF THE WET PIPING WHERE HIGHER
WIND VELOCITY IS EXPECTED.
* THE MINIMUM EXPOSED BARREL LENGTH IS MEASURED
FROM THE FACE OF THE FITTING TO THE INSIDE FACE OF THE
INSULATION, WALL, OR CEILING LEADING TO THE COLD SPACE,
WHICHEVER IS CLOSEST TO THE FITTING.
IF HUMIDITY AND TEMPERATURE DIFFERENTIAL
CAUSES CONDENSATION ON THE EXPOSED DRY
SPRINKLER, CONSIDER WRAPPING THE EXPOSED
BARREL WITH INSULATION, FOAM INSULATING
TAPE OR EQUIVALENT.
MINIMUM
(HEATED AREA)
SEAL THE CLEARANCE SPACE
EXPOSED
AROUND THE SPRINKLER TO AVOID
BARREL
LEAKAGE OF AIR INTO THE PROTECTED
LENGTH
AREA AND CONSEQUENT FORMATION OF
A
CONDENSATE AROUND THE FRAME, WHICH
DIMENSION CLEARANCE
COULD INHIBIT OPERATION OR CAUSE
HOLE
PREMATURE OPERATION. SEE BELOW FOR
RECOMMENDED METHODS.
______
ZEEINSIDE
SURFACE OF
INSULATION, WALL, OR
CEILING
THERMAL
ESCUTCHEON
BARRIER
DISCHARGE END OF SPRINKLER
PROTECTED (NON -CONDITIONED) AREA)
RECOMMENDED DRY SPRINKLER SEAL ARRANGEMENTS
WET PIPE (DRY SPRINKLER WITH STANDARD ESCUTCHEON SHOWN) WET PIPE
rt----------�� _ rt---
---1�--� -
-�IIII11IIII- 4- I
I�1I1�-
�
1�1�1Tt___�I
(HEATED AREA)
(HEATED AREA)
MINIMUM
MINIMUM
EXPOSED
EXPOSED
BARREL
BARREL
LENGTH
(SEE ABOVE)
DECKFLASHING
RASCO #4003910
INSIDE FACE
LENGTH
(SEE ABOVE)
(RECOMMENDED)
[SEAL
CLEARANCE
HOLE
INSULATED
FREEZER,
....... OR COOLER
STRUCTURE
OR EXTERIOR FRAMING
(PROTECTED AREA)
DISCHARGE END OF
`__'=tr
(PROTECTED AREA)
OF
DISCHARGE END
DRY SPRINKLER
DRY SPRINKLER
IN COLD AREA
IN COLD AREA
COMDRYDETI
*CAUTION*
RELIABLE DRY SPRINKLERS MAY BE INSTALLED IN A LISTED CPVC SPRINKLER FITTING, ONLY UPON
VERIFICATION THAT THE FITTING DOES NOT INTERFERE WITH THE SPRINKLER'S INLET.
Do not install dry sprinklers with standard inlets into CPVC fittings that have an internal obstruction; this will damage
the sprinkler, the fitting, or both.
Short inlet ("PL") versions of Reliable dry sprinklers are available that may or may not be compatible with fittings
having internal obstructions in existing installations. Sprinklers with the short inlet ("PL") should only be installed in
CPVC fittings of wet -pipe systems.
In all cases, verify sprinkler and fitting dimensions prior to installation to avoid interference.
Internal No Internal
Obstruction
Obstruction
I
I
Female Female
Pipe Pipe
Thread f I Thread
CPVC Fitting with Internal Obstruction CPVC Fitting -
No Internal Obstruction
1
Shorter Longer
Inlet Inlet
Male Male
Pipe Pipe
Thread Thread
I177
Dry Sprinkler Dry Sprinkler
Short Inlet ("PL") Standard Inlet
BE SURE TO ORDER THE CORRECT SPRINKLERS FOR YOUR
APPLICATION
COMDRYDE2
Fig. 12
15.
ON
Fig. 13 - Model F3R Wrench
Fig. 14 - Model XL02 Wrench
16.
MATERIAL SPECIFICATIONS
ITEM #
DESCRIPTION
MATERIAL SPECIFICATION
1
FRAME
BRASS PER UNS C83600
2
DEFLECTOR
BRONZE PER UNS C51000
3
LOAD SCREW
BRASS PER UNS C22000
4
SEAT ADAPTOR
BRASS ALLOY PER UNS C36000
5
BULB INSERT
COPPER ALLOY PER UNS C31400
6
GLASS BULB
GLASS W/GLYCERIN SOLUTION
7
ORIFICE ADAPTOR
BRASS ALLOY PER UNS C36000
8
OUTER TU BE
GALVANIZED STEEL
9
INNER TUBE
BRASS ALLOY PER UNS C23000
10
YOKE
BRASS ALLOY PER UNS 038000
11
INLET
BRASS ALLOY PER UNS C35330
12
CAP
BRASS ALLOY PER UNS C54400
13
SPRING WASHER/SEAL
PTFE COATED BERYLLIUM NICKEL
14
FLIP DISK
BRASS ALLOY PER UNS C54400
15
CAN/ESCUTCHEON
PAINTED OR PLATED MILD STEEL
(NOT USED ON ALL MODELS)
(PIPE WRENCH MAY ONLY BE USED ON OUTER STEEL PIPE OF SPRINKLER)
COMDRYDET13
,PPEARANCE OF DEFLECTOR MAY VARY DEPENDING ON MODEL
Fig. 15
17.
Installation Instructions
Model F3QR56 Dry sprinklers must only be installed in the
following fittings:
1. The side outlet of an ANSI B 16.3 class 150 (malleable
or ductile) or ANSI B16.4 class 125 (cast) iron pipe
tee
2. The run outlet of an ANSI B 16.3 class 150 (malleable
or ductile) or ANSI B16.4 class 125 (cast) iron pipe
tee, with the side outlet plugged (wet -pipe systems
only)
3. Spears Manufacturing Company Brass Thread In-
sert Style or Special Reinforced Plastic Thread Style
Listed adapter or tee (wet -pipe systems only) (gasket
sealed outlets shall not be used)
4. Any Listed CPVC sprinkler adapter or tee only in ac-
cordance with Fig. 12 and upon verification that the
CPVC adapter or tee does not interfere with the sprin-
kler's inlet (wet -pipe systems only) (gasket sealed
outlets shall not be used)
Model F3QR56 dry sprinklers must not be installed into el-
bows, welded outlets, gasket sealed outlets, or couplings.
Installation of the Model F3QR56 Dry sprinkler is not recom-
mend in copper pipe systems, as this may reduce the life
expectancy of the sprinkler.
In all dry -pipe system installations, the Model F3QR56 Dry
sprinkler must be installed with protrusion into the fitting in
accordance with Fig. 1 through Fig. 10 in this Bulletin. Do
not install Model F3QR56 Dry sprinklers with the standard
(long) inlet fitting into CPVC fittings that have an internal
obstruction (see Fig. 12); this will damage the sprinkler, the
fitting, or both. Model F3QR56 Dry sprinklers are available
with a short "PL" inlet fitting for installation on CPVC fittings
of wet -pipe sprinkler systems only.
Model F3QR56 Dry sprinklers connected to wet -pipe sys-
tems must be installed with the Exposed Minimum Barrel
Length required by Fig. 11 located in a Heated Area.
An orange protective clip is factory installed on the sprin-
kler to protect the glass bulb thermal element from dam-
age. The clip should remain in place during installation of
the sprinkler and be removed when the sprinkler system is
placed in service. Sprinklers with 3/4" NPT and ISO7-1 R3/4
inlets are supplied with a protective cap on the inlet that
must be removed before installation.
Use the following steps for installation:
1. Cut a hole in the wall or ceiling directly in -line with
the outlet of the fitting. See the Installation Data table
for the recommended hole diameter based on the es-
cutcheon or cover plate option selected.
2. Apply pipe joint compound or PTFE tape to the male
threads of the sprinkler's inlet fitting.
3. Install the sprinkler in the fitting using the installation
wrench specified in the Installation Data table. The
Model F3R wrench is designed to be inserted into the
groves in the sprinkler's wrench boss as shown in Fig.
13. The Model XLO2 wrench is designed to fit into the
cup and engage the wrench boss as shown in Fig.
14. Do NOT wrench any part of the sprinkler assembly
other than the wrench boss. When inserting or remov-
ing the wrench from the sprinkler, care should be tak-
en to prevent damage to the sprinkler. The sprinkler
is then tightened into the pipe fitting to achieve a leak
free connection. The recommended minimum to max-
imum installation torque is 22 - 30 lb-ft (30 — 40 N-m)
for 1" NPT and IS07-1R1 sprinklers, and 14 - 20 lb-ft
(19 — 27 N-m) for 3/4" NPT and ISO7-1 R3/4 sprinklers.
3a.Alternatively, where access to the outer tube of
the sprinkler is available, the Model F30R56 Dry
sprinkler may be installed using a pipe wrench.
The pipe wrench shall only be permitted to inter-
face with the galvanized steel outer tube portion of
the sprinkler (Item #8 in Fig. 15). Do NOT wrench
any other portion of the sprinkler assembly. A pipe
wrench can install the sprinkler into the fitting with
a large amount of torque; consideration should be
given to the need for future removal of the sprin-
kler because the installation torque will have to be
matched or exceeded to remove the sprinkler. The
recommended minimum to maximum installation
torque is 22 - 30 lb-ft (30 — 40 N-m) for 1" NPT
and ISO7-1 R1 sprinklers, and 14 - 20 lb-ft (19 — 27
N-m) for 3/4" NPT and ISO7-1 R3/4 sprinklers.
4. Standard and Model HB escutcheons can be in-
stalled by slipping the escutcheon over the can until
the escutcheon is seated against the ceiling or wall.
Model F1 escutcheons are installed by pressing the
escutcheon onto the collar until the escutcheon is
seated against the ceiling or wall. The Model FP es-
cutcheon is installed by pressing or threading the es-
cutcheon into the cup by hand; the escutcheon can
be tightened against the ceiling or wall by turning the
escutcheon in a clockwise direction and removed by
turning the escutcheon in a counter -clockwise direc-
tion. To install the Model CCP cover plate, first remove
the protective clip. Install the Model CCP cover plate
on the sprinkler by pressing or threading the cover
plate into the cup by hand; the cover plate can be
tightened against the ceiling by turning the cover
plate in a clockwise direction and removed by turning
the cover plate in a counter -clockwise direction.
5. Remove the orange protective clip when placing the
sprinkler system in service.
18.
Installation Data
Sprinkler
Suggested Hole Diameter
Required Centerline of Sprinkler
Installation
Model
Escutcheon or Cover Plate
in Wall or Ceiling
Tube/Inlet to Finished Ceiling
Wrench
Vertical Dimension*
Standard Escutcheon
2-1/8"(54 mm)
F3R
HB Extended Escutcheon
2-1/2" (64 mm)
F3QR56 Dry
Not
F1 Recessed Escutcheon
2-1/4" (57 mm)
Pendent
Applicable
FP Recessed Escutcheon
XL02
2-1/2" (64 mm)
CCP Cover Plate
Standard Escutcheon
2-1/8" (54 mm)
4-5/8" to 12-5/8"
(118 mm to 321 mm)
F3R
HB Extended Escutcheon
2-1/2" (64 mm)
F3QR56 Dry
F1 Recessed Escutcheon
2-1/4" (57 mm)
cULus, NYC
Horizontal
Sidewall
4-5/8" to 6-5/8"
118 mm to 168 mm
( )
FP Recessed Escutcheon
2 1/2" (64 mm)
F1 Recessed Escutcheon
2-1/4" (57 mm)
FM
XL02
4-5/8" to 12-5/8"
FP Recessed Escutcheon
2-1/2" (64 mm)
(118 mm to 321 mm)
F301356 Dry
N/A
1-1/2" (38mm)
Not Applicable
F3R
Upright
*Note: Based on 5/8" (16 mm) centerline of sprinkler tube/inlet to defector vertical distance.
Maintenance
The Model F3QR56 Dry Sprinklers should be inspected
and the sprinkler system maintained in accordance with
NFPA 25. Do not remove the factory applied thermally sen-
sitive wax fillet between the bulb supporting cup and the
wrenching boss. Do not replace this wax with a substitute
substance.
An Alternate substance may interfere with proper operation
of the sprinkler. Do not clean sprinklers with soap and water,
ammonia or any other cleaning fluids. Remove dust by us-
ing a soft brush or gently vacuuming. Replace any sprin-
kler which has been painted (other than factory applied) or
damaged in any way. A stock of spare sprinklers should be
maintained to allow quick replacement of damaged or op-
erated sprinklers. Prior to installation, sprinklers should be
maintained in the original cartons and packaging until used
to minimize the potential for damage to sprinklers that would
cause improper operation or non -operation.
Ordering Information
Specify:
1. Sprinkler: [Model F3QR56 Dry Pendent SIN R5714]
[Model F3QR56 Dry Horizontal Sidewall SIN R5734]
[Model F2QR Dry Upright SIN R5724]
2. Escutcheon/Cover Plate: [None][Standard escutch-
eon][Model HB extended escutcheon][Model F1 re-
cessed escutcheon][Model FP recessed escutcheon]
[Model CCP cover plate — pendent only]
3. Inlet Threads: [1" NPT][ISO7-1R1][3/4" NPT][IS07-
1 R3/4]
4. Inlet Fitting: [Long — Standard Inlet Fitting][Short "PL"
— Wet Pipe Systems only]
5. Sprinkler Temperature Rating: See Temperature Rat-
ings table
6. Sprinkler Finish: See Finishes Table
7. Escutcheon/Cover Plate Finish: See Finishes Table
8. Length:
*For dry pendents and dry sidewalls: "A" Dimen-
sion is from face of tee to face of finished ceiling or
wall in 1/4" (6mm) increments. See Fig. 1 through
Fig. 9.
*For dry uprights: Order dimension is from face of
tee to top of deflector in 1/4" (6mm) increments.
See Fig. 10.
Notes:
1. For Dry Upright, customer is responsible for determining
the correct deflector distance from structure above.
2. Length is based on normally gauged pipe thread "make-
up" of .600" (15mm) per ANSI B2.1 (approximately 7-1/2
threads).
The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, Factory
Mutual Research Corporation, or other similar organizations and also with the provisions of governmental codes or ordinances whenever applicable.
Products manufactured and distributed by Reliable have been protecting life and property for almost 100 years.
Manufactured by
Reliable
Reliable Automatic Sprinkler Co., Inc.
(800) 431-1588
Sales Offices
(800) 848-6051
Sales Fax
(914) 829-2042
Corporate Offices
www.reliablesprinkler.com
Internet Address
®Recycled
Paper
Revision lines indicate updated or new data.
EG. Printed in U.S.A. 09/19 P/N 9999970175
UponorAquaPEX®White, coils
Submittal information
Revision M: Sept. 18, 2018
Project information
Job name:
Location: Part no. ordered:
Uponof
Engineer: Date submitted:
Contractor: Submitted by:
Manufacturer's representative: Approved by:
Technical data
Material: Crosslinked polyethylene PEX-a Engel Method; PEX 5106
Standard grade hydrostatic ratings (PPI): 200°F (93°C) at 80 psi (551 kPa)
180°F (82°C) at 100 psi (689 kPa)
73.4°F (23°C) at 160 psi (1,103 kPa)
'/2", %", 1", 1'/4", 1'/2" and 2" UponorAquaPEX® White only:
---
120°F (49°C) at 130 psi (896 kPa)
Linear expansion rate: 1.1'/10°F/100' (27.94mm/5.56°C/30.48m)
Product information and application use
Uponor AquaPEX White is used for hot and cold domestic potable water distribution and residential fire safety as well
_
as radiant heating/cooling and hydronic piping systems containing no ferrous corrodible components or where ferrous
components are isolated from the piping.
✓ Description
Part number
I.D.
O.D.
Weight
'/4' Uponor AquaPEX White, 100-ft. coil
F1040250
0.241"
0.375"
4.0 lbs.
Uponor AquaPEX White, 400-ft. coil
F1090375
0.350"
0.500"
20.0 lbs.
Uponor AquaPEX White, 1,000-ft. coil
F1120375
0.350"
0.500"
44.0 lbs.
''/2" Uponor AquaPEX White, 100-ft. coil
F1040500
0.475"
0.625"
6.0 lbs.
%" Uponor AquaPEX White, 300-ft. coil
F1060500
0.475"
0.625"
18.0 lbs.
''/z" Uponor AquaPEX White, 500-ft. coil
F1100500
0.475"
0.625"
27.6 lbs.
''/z" Uponor AquaPEX White, 1,000-ft. coil
F1120500
0.475"
0.625"
54.0 lbs.
Uponor AquaPEX White, 300-ft. coil
F1060625
0.574"
0.750"
28.0 lbs.
Uponor AquaPEX White, 1000-ft. coil
F1120625
0.574"
0.750"
86.0 lbs.
Uponor AquaPEX White, 100-ft. coil
F1040750
0.671"
0.875"
10.0 lbs.
Y44" Uponor AquaPEX White, 300-ft. coil
F1060750
0.671"
0.875"
34.0 lbs.
%" Uponor AquaPEX White, 500-ft. coil
F1100750
0.671"
0.875"
54.0 lbs.
1" Uponor AquaPEX White, 100-ft. coil
F1041000
0.862"
1.125"
20.0 lbs.
1" Uponor AquaPEX White, 300-ft. coil
F1061000
0.862"
1.125"
56.0 lbs.
1" Uponor AquaPEX White, 500-ft. coil
F1101000
0.862"
1.125"
93.0 lbs.
1'/4' Uponor AquaPEX White, 100-ft. coil
F1061250
1.054"
1.375"
34.0 lbs.
1'/4" Uponor AquaPEX White, 300-ft. coil
F1021250
1.054"
1.375"
106.0 lbs.
1'/z" Uponor AquaPEX White, 100-ft. coil
F1061500
1.244"
1.625"
44.0 lbs.
1'/z" Uponor AquaPEX White, 300-ft. coil
F1021500
1.244"
1.625"
133.0 lbs.
2" Uponor AquaPEX White, 100-ft. coil
F1062000
1.629"
2.125"
68.2 lbs.
2" Uponor AquaPEX White, 200-ft. coil
F1052000
1.629"
2.125"
136.4 lbs.
2" Uponor AquaPEX White, 300-fit. coil
F1022000
1.629"
2.125"
204.6 lbs.
2'/i' Uponor AquaPEX White, 100-ft. coil
F1062500
2.011"
2.625"
88.0 lbs.
2'/i' Uponor AquaPEX White, 300-ft. coil
F1022500
2.011"
2.625"
264.0 lbs.
3" Uponor AquaPEX White, 100-ft. coil
F1063000
2.400"
3.125"
128.0 lbs.
3" Uponor AquaPEX White, 300-ft. coil
F1023000
2.400"
3.125"
384.0 lbs.
Installation
Use ProPEX® fittings for %" through 3" pipe.' Refer to the ProPEX Connections Instructional
Guide, Uponor
Piping Pocket Guide,
Plumbing Design Assistance
Manual (PDAM), Complete Design Assistance Manual (CDAM), Hydronic Piping
Design Assistance Manual (HPDAM) or AquaSAFET1A Residential
Fire Sprinkler
Installation Guide for more information.
Listings2
Codes
Standards
cNSFus-fs3; cNSFus-pw; cQAlus P321; UL;
IAPMO; ICC; IPC; IMC; IRC;
ANSI/NSF 14; ANSI/NSF 61; ASTM F876; ASTM F877; ASTM F1960; ASTM
CSA; PPI TR-4; ICC-ES; BMEC; CCMC
UPC; UMC; NSPC; HUD;
F2023; ASTM E84; CAN/ULC S102.2; ASTM
E119/UL 263; CAN/ULC S101;
UFGS; NPC of Canada;
ASTM E814/ULC S115;
CSA B137.5; CSA B214;
NBC of Canada
UL 18213; ULC/ORD-C199P3;
AWWA C9044
Related applications Contact information
PEX-a plumbing systems Uponor, Inc. Uponor Ltd.
AquaSAFETM fire safety systems 5925 148"' Street West 6510 Kennedy Road
Radiant heating and cooling systems Apple Valley, MN 55124 USA Mississauga, ON L5T 2X4 CANADA
Hydronic piping systems Phone: 800.321.4739 Phone: 888.994.7726
Fax: 952.891.2008 Fax: 800.638.9517
uponorpro.com uponorpro.com
'ProPEX® is a registered trademark of Uponor, Inc. ProPEX- is a trademark of Uponor Ltd.
2Visit listing agency's website for complete information. 3For 3/4", 1" and 1'W pipe only. 4For %" to 3" pipe.
ProPEX° Ring
Submittal information
Revision I: Nov. 1, 2018
Project information
Job name:
Location: Part no. ordered:
Engineer: Date submitted:
Contractor: Submitted by:
Manufacturer's representative: Approved by:
Technical data
Material: Engel -method crosslinked polyethylene (PEX-a)
Density: 926 to 940 kg/m3
Degree of crosslinking: 70% to 89%
Product information and application use
Uponor ProPEX® rings are required to make a proper ProPEX connection.' The ProPEX
ring with stop includes a leading edge chamfer and stop edge.
✓ Description Part number
ProPEX Ring, %"
ProPEX Ring with Stop, '/2"
ProPEX Ring with Stop, %"
ProPEX Ring with Stop, 3/4"
ProPEX Ring with Stop, 1"
ProPEX Ring with Stop, 1'/4"
ProPEX Ring with Stop, 1'/2"
ProPEX Ring with Stop, 2"
ProPEX Ring with Stop, 2'/2"
ProPEX Ring with Stop, 3"
Installation
Q4690302
Q4690512
Q4690625
Q4690756
Q4691000
Q4691250
Q4691500
Q4692000
Q4692500
Q4693000
uponof
Length
I.D.
O.D.
Weight
0.54"
0.49"
0.74"
0.005lbs.
0.63"
0.63"
0.87"
0.006lbs.
0.79"
0.75"
1.00"
0.008lbs.
0.87"
0.88"
1.13"
0.012lbs.
1.10"
1.13"
1.42"
0.020lbs.
1.35"
1.38"
1.66"
0.030lbs.
1.61"
1.63"
1.91"
0.040 lbs.
1.97"
2.14"
2.61"
0.133lbs.
2.61"
2.66"
3.25"
0.230lbs.
3.12"
3.16"
3.87"
0.400lbs.
Square cut the Uponor PEX tubing. Remove excess material. Slide the ProPEX ring over the end of the tubing (maximum 'lid' over -hang for rings without stop).
When using the ProPEX ring with stop, slide the ring on the tubing with the chamfered edge first until the end of the tubing contacts the stop edge. Expand the
tubing and ring. If using the ProPEX Manual Expander Tool, rotate the tool a quarter turn after each expansion to prevent the formation of grooves. Remove the
expansion tool and fully seat the tubing and ring against the shoulder of the fitting. Make ProPEX connections at temperatures above 5°F/-15°C. For more
information, refer to the Uponor ProPEX Connections Instructional Guide.
Listings'
cNSFus-fs3; cNSFus-pw; cNSFus-rfh; cQAlus; UL; CSA; PPI TR-4; ICC-ES; IAPMO; BMEC; CCMC; cQAlus P321
Codes
ICC; IPC; IMC; IRC; UPC; UMC; NSPC; HUD; UFGS; NPC of Canada; NBC of Canada
Standards
ANSI/NSF 14; ANSI/NSF 61; ASTM F876; ASTM F877; ASTM F1960; ASTM F2023; ASTM E84; CAN/ULC S102.2; ASTM E119/UL 263; CAN/ULC S101; ASTM
E814/ULC S115; CSA 13137.5; CSA B214; UL 18213; ULC/ORD-C199P3
Related applications Contact information
PEX-a plumbing systems
Uponor Inc.
Uponor Ltd.
AquaSAFE fire safety systems
5925 148"' Street West
6510 Kennedy Road
Hydronic radiant heating and cooling systems
Apple Valley, MN 55124 USA
Mississauga, ON L5T 2X4 CANADA
Snow melting systems
Phone: 800.321.4739
Phone: 888.994.7726
Turf conditioning systems
Fax: 952.891.2008
Fax: 800.638.9517
Permafrost prevention systems
uponorpro.com
uponorpro.com
'ProPEX® is a registered trademark of Uponor, Inc. ProPEXT" is a trademark of Uponor Ltd.
2Visit listing agency's website for complete information; 3For '/2",'/", 1", 11/", 1'/2" and 2" tubing only
ProPEXO Engineered
Submittal information
Revision H: May 23, 2019
Project information
Job name:
Polymer (EP) Tee
Location: Part no. ordered:
Engineer: Date submitted:
Contractor: Submitted by:
Manufacturer's representative: Approved bv:
Technical data
Material: Engineered polymer (EP)
Maximum temperature (no pressure): 320°F (160°C)
Maximum working temperature/pressure: 210*F (99*C) at 150 psi (1,034 kPa)
Product information and application use
ProPEX® engineered polymer (EP) tees make diverting connections for Uponor crosslinked
polyethylene (PEX-a)tubing for use in hot and cold domestic potable water systems,
residential fire sprinkler systems and hydronic radiant heating and cooling systems. Each
end of the tee is manufactured with an Uponor ProPEX fitting for connections to Uponor
AquaPEX® or Wirsbo hePEXTM tubing.'
Note: Branch size is listed last in the part descriptions.
Uponof
Part
✓
Equivalent Equivalent
cv
cv
Description
number
A B Weight
length (ft.) length (ft.)
through
branch
through branch
ProPEX EP Tee, ''M." PEX x'/z' PEX x'/" PEX Q4755060
2.50" 1.53" 0.02 lbs.
1.0 6.3
7.7
3.4
ProPEX EP Tee, %" PEX x'/:' PEX x'/:' PEX* Q4757575
3.30" 1.94" 0.05 lbs.
1.5 15.6
15.7
5.4
ProPEX EP Tee, 1" PEX x 1" PEX x 1" PEX* Q4751010
4.10" 2.47" 0.07 lbs.
1.3 12.7
30.5
11.3
ProPEX EP Tee, 1'/4" PEX x 1'/4" PEX x 1'/4" PEX* Q4751313
4.80" 3.22" 0.15 lbs.
3.8 8.6
34.0
23.9
ProPEX EP Tee, 1 Yz' PEX x 1'/." PEX x 1'M." PEX Q4751515
5.80" 3.82" 0.25 lbs.
1.8 10.6
63.7
31.0
ProPEX EP Tee, 2" PEX x 2" PEX x 2" PEX Q4752000
7.45" 4.79" 0.38 lbs.
0.8 15.5
150.7
52.5
ProPEX EP Tee, 21/' PEX x 21/z' PEX x 21/z' PEX Q4752500
10.56" 5.45" 1.14 lbs.
2.7 22.3
197.2
81.5
ProPEX EP Tee, 3" PEX x 3" PEX x 3" PEX Q4753000
12.26" 6.37" 1.86 lbs.
2.8 23.9
286.6
122.8
Installation
Use the appropriate ProPEX Ring for PEX-a tubing. Refer to the Uponor Professional Plumbing Installation Guide, AquaSAFET"^ Residential Fire
Sprinkler Installation
Guide or Uponor Radiant Installation Handbook for additional information.
Standards
ASTM E84; ASTM E119; ASTM E814; ASTM F877; ASTM F1960; CAN/CSA B137.5; NSF 14; NSF 61
Codes
IBC; IMC; IPC; IRC; NPC of Canada; NSPC; UMC; UPC
Listings
cNSFus-pw; *cNSFus-pw-fs; cQAlus P321; HUD MR 1269; ICC-ES-PMG-1006; ICC-ES-PMG-1012; *UL 1821; *ULC/ORD-C199P; U.P. Code
Related applications
Contact information
PEX-a plumbing systems
Uponor, Inc.
Uponor Ltd.
Hydronic radiant heating and cooling systems
5925 148t' Street West
6510 Kennedy Road
Snow and ice melting systems
Apple Valley, MN 55124 USA Mississauga, ON L5T 2X4 CANADA
Turf conditioning systems
Phone: 800.321.4739
Phone: 888.994.7726
Permafrost prevention systems
Fax: 952.891.2008
Fax: 800.638.9517
AquaSAFETm fire safety systems
uponorpro.com
uponorpro.com
'ProPEX® is a registered trademark of Uponor, Inc. ProPEXT" is a trademark of Uponor Ltd.
ProPEX° Engineered Polymer (EP) Reducing Tee (up to 11/2") uponof
Submittal information
Revision I: Sept. 16, 2019
Project information
Job name:
Location: Part no. ordered:
Engineer: Date submitted:
Contractor: Submitted by:
Manufacturer's representative: Approved by:
Technical data
Material: Engineered polymer (EP) n�
Maximum temperature (no pressure): 320°F (160°C)
Max. working temperature/pressure: 210°F (99°C) at 150 psi (1,034 kPa)
Product information and application use
ProPEX® engineered polymer (EP) reducing tees make diverting connections for Uponor PEX-a pipe for use in hot and cold B
domestic potable water systems, residential fire sprinkler systems and hydronic radiant heating and cooling systems. Each
end of the tee is manufactured with an Uponor ProPEX fitting for connections to Uponor AquaPEX11 or Wirsbo hePEXTM
pipe.' Note: Branch size is listed last in the part descriptions.
✓ Description
Part
A
B
Weight
Equiv, length (ft.)
Equiv. length
Cv
Cv
number
through
(ft.) branch
through
branch
ProPEX EP Reducing Tee,''/2" PEX x'/i' PEX x %" PEX
Q4755575
2.86"
1.76"
0.03 lbs.
1.0
15.6
7.7
5.4
ProPEX EP Reducing Tee, '/<" PEX x'/i' PEX x'/i' PEX
Q4757555
3.10"
1.70"
0.04 lbs.
3.5
6.4
4.6
3.4
ProPEX EP Reducing Tee, '/<" PEX x'/z' PEX x'/;' PEX*
Q4757557
3.10"
1.94"
0.04 lbs.
2.3
16.1
5.4
5.4
ProPEX EP Reducing Tee, '/<" PEX x'/;' PEX x PEX
Q4757563
3.30"
1.85"
0.05 lbs.
N/A
N/A
N/A
N/A
ProPEX EP Reducing Tee, '/<" PEX x'/;' PEX x'/z' PEX*
Q4757550
3.30"
1.70"
0.04 lbs.
2.0
7.6
14.2
3.1
ProPEX EP Reducing Tee, '/<" PEX x'/;' PEX x 1" PEX*
Q4757710
3.64"
2.32"
0.08 lbs.
1.5
5.7
15.7
8.7
ProPEX EP Reducing Tee, 1" PEX x'/i' PEX x 1" PEX
Q4751501
3.71"
2.43"
0.09 lbs.
1.98
9.7
12.3
5.7
ProPEX EP Reducing Tee, 1" PEX x'/d' PEX x'/ PEX
Q4751750
3.65"
1.96"
0.07 lbs.
2.27
6.69
3.1
13.2
ProPEX EP Reducing Tee, 1" PEX x'/<" PEX x'/4" PEX*
Q4751775
3.90"
2.24"
0.08 lbs.
2.4
16.7
12.8
5.3
ProPEX EP Reducing Tee, 1" PEX x'/<" PEX x 1" PEX*
Q4751751
3.90"
2.47"
0.08 lbs.
2.4
15.1
12.9
10.5
ProPEX EP Reducing Tee, 1" PEX x'/;' PEX x 1%" PEX
Q4751753
4.15"
2.95"
0.12 lbs.
2.74
19.48
14.7
12.0
ProPEX EP Reducing Tee, 1" PEX x 1" PEX x'/;' PEX*
Q4751150
4.10"
2.00"
0.08 lbs.
1.2
6.5
32.2
3.4
ProPEX EP Reducing Tee, 1" PEX x 1" PEX x %" PEX*
Q4751175
4.10"
2.24"
0.09 lbs.
1.7
6.4
27.8
8.2
ProPEX EP Reducing Tee, 1" PEX x 1" PEX x 1 '/;' PEX*
Q4751113
4.38"
2.95"
0.13 lbs.
6.52
5.37
15.0
28.0
ProPEX EP Reducing Tee, 1%" PEX x'/<" PEX x'/<" PEX*
Q4751377
4.11"
2.38"
0.09 lbs.
2.74
7.41
7.3
12.0
ProPEX EP Reducing Tee, 1%" PEX x'/<" PEX x 1" PEX*
Q4751371
4.37"
2.62"
0.11 lbs.
2.70
7.59
13.9
12.1
ProPEX EP Reducing Tee, 1%" PEX x'/<" PEX x 1Y<" PEX*
Q4751373
4.61"
2.88"
0.13 lbs.
2.74
11.91
18.8
12.0
ProPEX EP Reducing Tee, 1'/<" PEX x 1" PEX x %" PEX*
Q4751317
4.50"
2.73"
0.11 lbs.
3.4
5.2
21.0
9.3
ProPEX EP Reducing Tee, 11/;' PEX x 1" PEX x 1" PEX*
Q4751311
4.70"
2.97"
0.12 lbs.
11.0
23.0
11.7
8.4
ProPEX EP Reducing Tee, 11/;' PEX x 11/4" PEX x'/;' PEX*
Q4751350
4.40"
2.15"
0.10 lbs.
1.9
3.9
45.2
4.1
ProPEX EP Reducing Tee, 11/4" PEX x 11/4" PEX x %" PEX*
Q4751337
4.70"
2.73"
0.13 lbs.
2.3
5.7
43.4
8.9
ProPEX EP Reducing Tee, 11/4" PEX x 11/4" PEX x 1" PEX*
Q4751331
5.00"
2.97"
0.14 lbs.
4.2
6.3
33.0
15.8
ProPEX EP Reducing Tee, 1'/z" PEX x'/<" PEX x %" PEX
Q4751577
4.37"
2.64"
0.13 lbs.
2.88
7.41
7.3
11.7
ProPEX EP Reducing Tee, 1'/z" PEX x'/<" PEX x 1'/z" PEX
Q4751575
4.97"
3.39"
0.19 lbs.
2.74
19.10
22.9
12.0
ProPEX EP Reducing Tee, 1'/z" PEX x 1" PEX x %" PEX
Q4751517
5.25"
3.06"
0.17 lbs.
4.0
5.1
19.5
9.3
ProPEX EP Reducing Tee, 1'/z" PEX x 1" PEX x 1" PEX
Q4751511
5.25"
3.30"
0.18 lbs.
4.3
6.5
18.9
15.6
ProPEX EP Reducing Tee, 11/2" PEX x 1" PEX x 11/2" PEX
Q4751505
5.40"
3.45"
0.20 lbs.
4.2
14.9
19.0
26.5
ProPEX EP Reducing Tee, 11/2" PEX x 11/4" PEX x %" PEX
Q4751537
5.50"
2.65"
0.18 lbs.
4.2
11.3
33.1
6.3
ProPEX EP Reducing Tee, 11/2" PEX x 11/4" PEX x 1" PEX
Q4751531
5.50"
2.85"
0.19 lbs.
3.1
13.1
36.4
11.2
ProPEX EP Reducing Tee, 11/2" PEX x 11/4" PEX x 11/4" PEX
Q4751533
5.50"
3.15"
0.21 lbs.
2.0
17.7
45.4
17.0
ProPEX EP Reducing Tee, 1'/z" PEX x 1'/2" PEX x'/i' PEX
Q4751550
4.95"
2.30"
0.14 lbs.
2.4
6.3
60.5
3.4
ProPEX EP Reducing Tee, 1'/z" PEX x 1'/2" PEX x %" PEX
Q4751557
5.30"
3.06"
0.20 lbs.
2.9
5.4
56.0
9.0
ProPEX EP Reducing Tee, 1'/2" PEX x 1'/2" PEX x 1" PEX
Q4751551
5.75"
3.30"
0.21 lbs.
3.1
6.9
53.8
15.3
ProPEX EP Reducing Tee, 1'/2" PEX x 1'/2" PEX x 11/4" PEX
Q4751553
5.80"
3.56"
0.22 lbs.
3.2
4.1
54.3
33.7
Installation
Use the appropriate ProPEX ring for PEX-a pipe. Refer to the Uponor Piping Systems
Installation
Guide,
the AquaSAFETm Residential Fire
Sprinkler Installation Guide or the Uponor
Radiant Installation Handbook for additional information.
Standards Codes
Listings
ASTM E84; ASTM E119; ASTM E814; IBC; IMC; IPC; IRC;
NPC of Canada;
cNSFus-pw; *cNSFus-pw-fs;
cQAlus P321;
HUD MR 1269; ICC-ES-PMG-1006;
ASTM F877; ASTM F1960; NSPC; UMC; UPC
ICC-ES-PMG-1012;
*UL 1821; *ULC/ORD-C199P; U.P. Code
CAN/CSA B137.5; NSF 14; NSF 61
Related applications
Contact information
PEX-a plumbing systems
Uponor Inc.
Uponor Ltd.
Hydronic radiant heating and cooling systems
5925 1481h Street West
6510 Kennedy Road
Snow and ice melting systems
Apple Valley,
MN 55124
USA
Mississauga, ON L5T 2X4
CANADA
Turf conditioning systems
Phone: 800.321.4739
Phone: 888.994.7726
Permafrost prevention systems
Fax: 952.891.2008
Fax: 800.638.9517
AquaSAFETM fire safety systems
uponorpro.com
uponorpro.com
'ProPEX® is a registered trademark of Uponor Inc. ProPEX" is a trademark of Uponor Ltd.
ProPEX® Engineered Polymer (EP) Elbow
Submittal information
Revision J: June 21, 2019
Project information
Job name:
Location: Part no. ordered:
Engineer: Date submitted:
Contractor: Submitted by:
Manufacturer's representative: ADDroved bv:
Technical data
Material: Engineered polymer (EP)
Maximum temperature (no
pressure): 320°F (160°C)
Maximum working
temperature/pressure: 210°F (99°C) at 150 psi (1,034 kPa)
Product information and application use
ProPEX® engineered polymer (EP) elbows make 90-degree connections for Uponor
crosslinked polyethylene (PEX-a) tubing for use in hot and cold domestic potable water
systems, residential fire safety and hydronic radiant heating and cooling systems. Each end
of the elbow is manufactured with an Uponor ProPEX fitting for connections to Uponor
AquaPEX® or Wirsbo hePEXTm tubing.'
Uponof
✓ Description
Part number
A
B
Weight
Equivalent
Cv
length (ft.)
ProPEX EP Elbow, '/z" PEX x'/z" PEX
Q4760500
1.30"
1.30"
0.02 lbs.
10.4
2.6
ProPEX EP Elbow, 3/4° PEX x 3/4" PEX*
Q4760750
1.60"
1.60"
0.03 lbs.
10.8
6.7
ProPEX EP Elbow, 1" PEX x 1" PEX*
Q4761000
2.10"
2.10"
0.07 lbs.
11.5
11.9
ProPEX EP Elbow, 1'/4" PEX x 1'/4" PEX*
Q4761250
2.45"
2.45"
0.11 lbs.
10.0
22.2
ProPEX EP Elbow, 1'/z" PEX x 1'/z" PEX
Q4761500
2.77"
2.77"
0.18 lbs.
11.5
29.7
ProPEX EP Elbow, 2" PEX x 2" PEX
Q4762000
3.76"
3.76"
0.30 lbs.
17.1
50.2
ProPEX EP Elbow, 2'/z" PEX x 2'/z" PEX
Q4762500
4.93"
4.93"
0.85 lbs.
20.0
86.0
ProPEX EP Elbow, 3" PEX x 3" PEX
Q4763000
5.88"
5.88"
1.44 lbs.
23.2
125.0
ProPEX EP 45 Elbow, 1'/2' PEX x 1'/2" PEX
Q4761515
2.32"
2.32"
0.13 lbs.
9.3
33.1
ProPEX EP 45 Elbow, 2" PEX x 2" PEX
Q4762020
2.91"
2.91"
0.32 lbs.
8.8
68.9
ProPEX EP 45 Elbow, 2'/2' PEX x 2'/2" PEX
Q4762525
3.83"
3.83"
0.65 lbs.
7.0
136.8
ProPEX EP 45 Elbow, 3" PEX x 3" PEX
Q4763030
4.48"
4.48"
1.07 lbs.
8.3
195.5
Installation
Use the appropriate ProPEX ring for PEX-a tubing. Refer to the Uponor Piping
Pocket Guide,
AquaSAFETm
Residential Fire Sprinkler Installation Guide
or Uponor
Radiant Installation Handbook for additional information.
Standards
ASTM E84; ASTM E119; ASTM E814; ASTM F877; ASTM F1960; CAN/CSA B137.5; NSF
14; NSF 61
Codes
IBC; IMC; IPC; IRC; NPC of Canada; NSPC; UMC; UPC
Listings
cNSFus-pw; *cNSFus-pw-fs; cQAlus P321; HUD MR 1269; ICC-ES-PMG-1006; ICC-ES-PMG-1012; *UL 1821; *ULC/ORD-C199P; U.P. Code
Related applications Contact information
PEX-a plumbing systems
Uponor Inc.
Uponor Ltd.
Hydronic radiant heating and cooling systems
5925 148t' Street West
6510 Kennedy Road
Snow and ice melting systems
Apple Valley, MN 55124 USA
Mississauga, ON L5T 2X4 CANADA
Turf conditioning systems
Phone: 800.321.4739
Phone: 888.994.7726
Permafrost prevention systems
Fax: 952.891.2008
Fax: 800.638.9517
AquaSAFE fire safety systems
uponorpro.com
uponorpro.com
1 ProPEX® is a registered trademark of Uponor, Inc. ProPEX- is a trademark of Uponor Ltd.
ProPEX° Fire Sprinkler Adapter
Submittal Information
Revision B: March 17, 2009
Project Information
Job Name:
Location: Part No. Ordered:
Engineer: Date Submitted:
Contractor: Submitted By:
Manufacturer's Representative: Approved By:
Technical Data
Material: 300 Series Stainless Steel
Product Information and Application Use
Use the ProPEX° Fire Sprinkler Adapter in conjunction with the
appropriate sprinkler to provide a multi -purpose residential fire
sprinkler system'. For residential applications, the system is
installed with the cold -potable portion of the Uponor plumbing
system. Make connections with Uponor ProPEX fittings. These
fittings are designed for use only with 3/4" or 1" AquaPEX°
White tubing in the Uponor AQUASAFE° Looped System.
uponof
✓ Description Part A B C D E Weight
Number
ProPEX Fire Sprinkler Adapter, 3/4" PEX x 1/2" FNPT Q7517550 0.75" 1.88" 2.50" 1.82" 1.41" 0.268 lbs.
ProPEX Fire Sprinkler Adapter, 1" PEX x 1/2" FNPT Q7511050 0.75" 1.88" 2.50" 2.06" 1.54" 0.408 lbs.
Installation
Use appropriate ProPEX Ring for connecting the tubing. Refer to the AquaPEX Installation Handbook or the Uponor AQUASAFE°
Installation Guide for additional information.
Standards
CAN/CSA B137.5; ASTM F877; ASTM F 1960
Codes
IPC; UPC; NSPC; IRC; IMC; NPC of Canada
Listings
ANSI/NSF 14- and 61-certified; U.P. Code; ICC ESR 1099; HUD MR 1269; UL 1821; ULC/ORD - C 199 P
Related Applications
PEX-a Plumbing Systems
AQUASAFE Fire Safety Systems
Contact Information
Uponor, Inc.
5925 1481h Street West
Apple Valley, MN 55124 USA
Phone: (800) 321-4739
Fax: (952) 891-2008
www.uponor-usa.com
Uponor Ltd.
2000 Argentia Rd., Plaza 1, Ste. 200
Mississauga, ON L5N 1W1 CANADA
Phone: (888) 994-7726
Fax: (800) 638-9517
www.uponor.ca
'ProPEX° is a registered trademark of Uponor, Inc. ProPEXTM is a trademark of Uponor Ltd.