The URL can be used to link to this page

FIR2021-0080+Fire_Sprinkler_Equipment_Specification_Sheets+7.28.2021_8.29.21_AM+2325452Viking Plastics Features • Sizes Available (Nominal): 3/4" (DN20) through 3" (DN80) pipe diameters, with a Standard Dimension Ratio (SDR) of 13.5 as specified in ASTM F442. • Environmental Specifications: Indoor use only. Maximum Ambient Temperature: 150°F (65°C) • Hazen -Williams C Value: 150 BIazeMaste,-'11" CPVC Pipe • Pressure Data: Working Pressure: 175 PSI (12.1 bar) at 150°F (65°C) • Specifications: • Meets NFPA 13R and 13D standards for residential occupancies as well as NFPA 13 standards for light hazard occupancies. • Pipe meets or exceeds ASTM F442. • Certified by NSF International for potable water services. • CPVC pipe from Viking Plastics use compound cell class 23547 (demonstrated highest structural properties). • cULus Listed, FM Approved, New York City (MEA) Approved, LPCB Approved. CPVC PIPE PHYSICAL DATA FM SF pPPCB Nominal Pipe Size Actual Outside Diameter Average Inside Diameter *Weight per 15' (4,6 m) length Length Approvals Part Number Inch DN Inch mm Inch mm Lb. Kg. Feet M 3/4" DN20 1.050 26,670 0.874 22,199 2.52 1,14 15 4.6 cU NSFFM 34PIPE 1" DN25 1.315 33,401 1.101 27,965 3.93 1,78 15 4.6 1PIPE 1 1/4" DN32 1.660 42,164 1.394 35,408 6.27 2,84 15 4.6 114PIPE 1 1/2" DN40 1.900 48,260 1.598 40,589 8.22 3,73 15 4.6 112PIPE 2" DN50 2.375 60,325 2.003 50,876 12.89 5,85 15 4.6 2PIPE 21/2" DN65 2.875 73,000 2.423 61,500 18.86 8,55 15 4.6 212PIPE 3" DN80 3.500 88,900 2.950 74,900 28.01 12,71 15 4.6 3PIPE Nominal Pipe Size Actual Outside Diameter Average Inside Diameter *Weight per 10' (3,05 m) length Length Approvals Part Number Inch DN Inch mm Inch mm Lb. Kg. Feet M 3/4" DN20 1.050 26,670 0.874 22,199 1.68 0,76 10 3,05 cU NSFFM 34PIPE10 1" DN25 1.315 33,401 1.101 27,965 2.62 1,19 10 3,05 1PIPE10 1 1/4" DN32 1.660 42,164 1.394 35,408 4.18 1,90 10 3,05 114PIPE10 1 1/2" DN40 1.900 48,260 1.598 40,589 5.48 2,49 10 3,05 112PIPE10 2" DN50 2.375 60,325 2.003 50,876 8.59 3,90 10 3,05 2PIPE10 21/2" DN65 2.875 73,000 2.423 61,500 12.57 5,70 10 3,05 212PIPE10 3" DN80 3.500 88,900 2.950 74,900 18.67 8,47 10 3,05 3PIPE10 NOTE: CPVC Pipe is produced in SDR 13.5 Dimensions in accordance with ASTM F442. Standard Dimension Ratio is the ratio of the outside pipe diameter to the wall thickness of the pipe. Blazemaster® is a registered trademark of Lubrizol. Specifications subject to change without notice *Empty pipe weights IMPORTANT. Installers should receive thorough hands-on training in the proper methods of assembly and installation of CPVC products Trusted above all TM NIKJW*i(R) Viking Plastid CPVC Pipe Product Specifications BIazeMastei-'11" CPVC Pipe Corrosion resistant CPVC fire sprinkler pipe, when installed in strict accordance with the manufacturer's design and instal- lation instructions, is UL and c-UL Listed by Underwriters Laboratories for use in the following: • Meets NFPA 13R and 13D standards for residential occupancies as well as NFPA 13 standards for light hazard occupancies. • Residential occupancies up to and including four stories in height as defined by NFPA 13R. • Residential occupancies as defined in the Standard for Sprinkler Systems in One and Two Family Dwellings, NFPA 13D. • Installation of private fire service mains and their appurtenances, NFPA 24. CPVC fire sprinkler pipe from Viking Plastics shall be employed in wet pipe systems only and are not listed for outdoor use. CPVC pipe must never be used in a system using compressed air or other gases. CPVC pipe from Viking Plastics also carries the following enhanced listings and approvals: • According to UL Listing • Can be flush at return air plenums • Exposed system risers NFPA 13D, 13R • Exposed basement NFPA 13D (solid wood joist) • Extended coverage (exposed) • 20' spacing on pendent in lieu of 15' • 18' spacing on sidewall in lieu of 14' • Use with combustible concealed sprinklers • UL Listed attic sprinkler head (to protect the floor below) • UL Listed attic sprinkler head with wet system piping (feed main and ridge installation) New and enhanced listings and approvals are being pursued. Always check with the appropriate Listing and Approval agency for details on current listing parameters. CPVC pipe meets all applicable standards for pressure rated applica- tion as required in ANSI -NSF Standard 14 and complies with ANSI -NSF Standard 61 for health effects and are marked with the NSF-pw end use marking. All CPVC fire sprinkler pipe shall be Listed by Underwriters Laboratories for wet pipe systems, and shall carry a rated working pressure of 175 psi @ 150°F (12 bar @ 65.5°C). *The FM Approval is limited to use in wet pipe fire protection sprinkler systems for light hazard occupancies in both concealed and exposed applications with certain restrictions. Piping must always be installed in strict accordance to the manufacturer's DESIGN AND INSTALLATION GUIDE, including product storage and handling, joining methods, supporting and bracing, expansion and con- traction allowance and testing, etc. National Fire Protection Association (NFPA) Standards 13, 13D, and 13R must be referenced for design and installation requirements in conjunction with the installation instructions. • Exposed sidewall sprinkler listing for exposed pipe & fittings • 24' extended coverage sidewall sprinkler, 12" drop, 155T sprinkler head • 18' extended coverage sidewall sprinkler, 12" drop, 165T sprinkler head • 16' extended coverage sidewall sprinkler, 12" drop, 175T sprinkler head • 14' standard coverage sidewall sprinkler, 12" drop, 200T sprinkler head Factory Mutual Approved* • Factory Mutual Approval exposed • Factory Mutual Approval above drop -in ceilings • Factory Mutual Approval exposed w/Soffi-Steel soffiting covering system All CPVC fire sprinkler pipe from Viking Plastics is manufactured in the USA. All CPVC pipe shall be packaged immediately after its manufacture to prevent damage and shall be stored indoors after production, at the manufacturing site, until shipped from the factory. The pipe shall bear the logo of the listing agencies, and shall carry the National Sanitation Foun- dation (NSF) seal of approval for potable water applications. CPVC products are intended for use in areas where the maximum ambi- ent temperature does not exceed 150°F (65.5°C). If the ambient tempera- ture is expected to exceed this limitation, refer to the manufacturer's DE- SIGN AND INSTALLATION GUIDE for additional information on methods to reduce the pipe exposure temperatures. CPVC pipe is not intended to be installed in outdoor applications. CPVC pipe is intended to be used in wet pipe systems only and have not been investigated for use in dry pipe systems. Special installation and design criteria relative to pipe hanger spacings, piping and sprinkler restraint, sprinkler temperature rating, piping locations, testing procedures and friction loss characteristics are specified in the manufacturer's installation instructions provided with the pipe. The manufacturer's installation instructions should be reviewed and the Authority Having Jurisdiction consulted before installation. Trusted above all TM NIKJW*iCR) Sprinkler Head Adapters BRASTICTm Adapter Straight Tee Size (inches) Part Number Box Qty with metal thread insert 3/4x1/2 V5003SBT-101 100 1 x 1/2 V50035BT-130 50 1 x 3/4 V50035BT-131 50 900 Elbow 3/4x1/2 V50073SBT-101 100 1 x 1/2 V50073SBT-130 50 1 x 3/4 V50073SBT-131 50 Tee 1 x 1 x 1 V50073SBT-101 1 x 1 x 1/2 V50073SBT-130 1 x 1 x 3/4 V50073SBT-131 * Brass starter thread molded into plastic, virtually eliminating cross -threading. 50 50 50 Female Adapter 3/4 x 1/2 V5003SBI-101 100 with metal thread insert 1 x 1/2 V5003SBI-130 50 1 x 3/4 V5003SBI-131 10 Spigot Female Adapter 3/4x 1/2 V50032SBI-101 100 with metal thread insert 1 x 1/2 V50032SBI-130 50 Sprinkler Head 90 1 3/4x 1/2 I V50073SBI-101 100 with metal thread insert 1 x 1/2 1 x 3/4 I V50073561-130 I V50073SBI-131 50 10 1-1/4x1/2 I V50073SBI-166 5 do Size (inches) 1x1x1 3/4 x 3/4 x 1/2 1x1x1/2 1-1/4x 1-1/4x 1/2 1-1/2 x 1-1/2 x 1/2 2x2x1/2 1 x 3/4 x 1/2 1-1/4x 1 x 1/2 1-1/2x 1-1/4x 1/2 2x1-1/2x1/2 Part Number V5012SBI-010 V5012SBI-101 V5012SBI-130 V5012SBI-166 V5012SBI-209 V5012SBI-247 V5012RSBI-124 V5012RSBI-156 V5012RSBI-199 V5012RSBI-237 Back to Back Cross 1xlx1/2x1/2(1-1/8) V50353SBIS-130 with metal thread insert 1x1x12x1/2(t-5n6) V50353SBIL-130 in Box Qty 50 10 50 5 5 2 10 5 5 2 20 1 Back to Back Tee 1 /2 x i/2 x 1 (t-va)V501133SBIS-075 30 with metal thread insert 1/2x1/2x1 (1-sne) V501133561L-075 30 4W Trusted above aII.T" V�KING� CPVC Standard Fittings Tee Size (inches) Part Number Box Qty Reducing Tee Size (inches) Part Number Box Qty 3/4 V5011-007 250 I 3/4 x 3/4 x 1 _ V5011 R-102 10 4% 1 V5011-010 100 1 x 3/4 x 3/4 V5011 R-125 100 1-1/4 V5011-012 25 1 x 3/4 x 1 I V5011 R-126 10 1-1/2 V5011-015 25 1 x 1 x 3/4 I V5011 R-131 100 2 V5011-020 2 1-1 /4 x 1 x 3/4 I V5011 R-157 5 2-1/2 V5011-025 1 1-1 /4 x 1 x 1 I V5011 R-158 25 3 V5011-030 1 1-1Ax1x1-1A V5011R-159 5 _ 1-1/4 x 1-1/4 x 3/4 V5011R-167 25 900Elbow 1-1/4 x 1-1/4 x 1 V5011R-168 25 3/4 V5007-007 250 1-1/4x1-1/4x1-1/2 V5011R-169 5 1 V5007-010 100 11-1/2x1-1/4x3/4 V5011R-201 5 1-1/4 V5007-012 25 I 1-1/2 x 1-1/4 x 1 V5011R-202 5 1-1/2 V5007-015 25 1-1/2 x 1-1/2 x 3/4 V5011 R-210 25 2 V5007-020 2 1-1/2 x 1-1/2 x 1 V5011R-211 25 1/2 V5007-025 1 1-1/2x1-1/2x1-1/4 V5011R-212 5 3 E12 V5007-030 1 1-1/2 x 1-1/2 x 2 V5011 R-213 5 x 3/4 V5007R-131 100 2 x 2 x 3/4 V5011 R-248 2 2 x 2 x 1 V5011 R-249 10 450 Elbow 3/4 _ V5006-007 250 2 x 2 x 1-1/4 V5011 R-250 2 1 V5006-010 100 2 x 2 x 1-1/2 V5011 R-251 2 1-1/4 V5006-012 5 2-1/2 x 2-1/2 x 1 V5011 R-289 1 1-1/2 V5006-015 5 2-1/2x2-1/2x1-1/4 V5011R-290 1 2 V5006-020 2 2-1/2 x2-1/2 x 1-1/2 V5011R-291 1 2-1/2 V5006-025 1 2-1/2 x 2-1/2 x 2 V5011 R-292 1 3 V5006-030 1 3 x 3 x 1-1/2 V5011 R-337 1 3 x 2 V5011 R-338 1 Cross 3/4 V5035-007 10 3 x 2-1/2 V5011 R-339 1 1 V5035-010 100 1-1/4 V5035-012 5 Bushing 1 x3/4 V5018-131 100 1-1/2 V5035-015 20 1-1 /4 x 3/4 V5018-167 25 2 V5035-020 1 1-1Ax1 V5018-168 25 2-1/2 V5035-025 1 1-1/2 x 3/4 V5018-210 5 1 x 1 x 3/4 x 3/4 V5035R-131J_ 10 1-1/2 x 1 V5018-211 25 1-1/2x1-1/4 V5018-212 25 Coupling 3/4 V5001-007 250 2 x 3/4 V5018-248 2 1 V5001-01 100 2 x 1 V5018249 2 1-1/4 V5001-012 25 2 x 1-1/4 V5018-250 2 1-1/2 V5001-015 25 2 x 1-1/2 V5018 251 2 2 V5001-020 10 2-1/2x1 V5018-289 15 2-1/2 V5001-025 1 2-1/2 x 1-1/4 V5018-290 1 3 V5001-030 1 2-1/2 x 1-1 /2 V5018-291 1 2-1/2 x 2 V5018-292 1 Reduced Coupling 3 x 1-1/2 V5018-337 15 1 x3/4 V5001R-131 10 3 x 2 V5018-338 1 i 1-1 /4 x 1 V5001 R-168 5 3 x 2-1/2 V5018-339 1 #' 1-1/2 x 3/4 V5001 R-210 5 1-1/2x1 V5001R-211 5 1-1/2x1-1A V5001R-212 5 Cap 3/4 V5017-007 250 2 x 1 V5001 R-249 2 1 V5017-010 100 2x1-1/2 V5001R-251 2 1-1/4 V5017-012� 5 1-1/2 V5017-015 5 2 V5017-020 2 2-1/2 V5017-025 1 3 V5017-030 1 May 2014 CPVC Pipe Size(inches) 11 Part Number 11 Box Qty 3/4 34PIPE 240 1 1 1PIPE 180 1-1/4 114PIPE 105 *l� 1-1/2 112PIPE 75 y 2 _ 2PIPE _ 60 2-1/2 212PIPE _ 30 1 3 3PIPE 15 CPVC Transition Fittings Female Adapter N Size (inches) �I Part Number Box Qty Grooved Coupling Size (inches) Part Number Box Qty with metal thread insert Adapter 3/4 V5003BI-007 10 1-1/4 _V5001G-012 30 J 1 V5003B1-010 50 1-1/2 _V5001G-015 25 J 1-1/4 V5003B1-012 5 2 _V5001G-020 15 J 1-1/2 V5003BI-015 5 2-1/2 V5001G-025 4 2 V5003BI-020 2 3 V5001G-030 2 Spigot Female Adapter 3/4 V50032BI-007 250 Standard Union 3/4 _I V5033E-007 I 1 with metal thread insert 1 V5003261-010 100 � 1 _I V5033E-010 I 1 Male Adapter 3/4 V5004BI-007 10 with metal thread insert 1 V5004BI-010 10 1-1/4 V5004BI-012 5 1-1/2 V5004BI-015 5 2 V5004BI-020 2 Accessories Solvent Cement Size (inches) Part Number Box Qty Dauber Size (inches) Part Number Box Qty Quart V5097Q 12 � Small V5093-5 100 Pint V5097P 12 Large V5093-L 100 Test Plug 1/2 V450-005 50 Roller N/A V5097 24 Brush N/A V5096 12 May 2014 Recommended Installation Practices and Precautions for Freedom® CPVC Systems E Dos MRW • Install product according to the manufacturer's instructions. • Follow recommended safe work practices. • Make certain that thread sealants, gasket lubricants, or fire stop materials are compatible with BlazeMaster® CPVC. • Use only latex -based paints if painting is desired. • Keep pipe and fittings in original packaging until needed. • Cover pipe and fittings with an opaque tarp if stored outdoors. • Follow proper handling procedures. • Use tools designed for use with plastic pipe and fittings. • Use proper solvent cement and follow application instructions. • Use a drop cloth to protect interior finishes. • Cut the pipe ends square. • Deburr and bevel the pipe end before solvent cementing. • When solvent cementing, rotate the pipe 1/4 turn when bottoming pipe in fitting socket. • Always apply solvent cement to the pipe first then fitting. • Avoid puddling of solvent cement in fittings and pipe. • Make certain that solvent cement does not run and plug the sprinkler head orifice. • Follow the manufacturer's recommended cure times prior to pressure testing. • Fill lines slowly and bleed the air from the system prior to pressure testing. • Support sprinkler head properly to prevent lift up of the head through the ceiling when activated. • Keep threaded rod within 1/16"of the pipe. • Install BlazeMaster CPVC pipe and fittings in wet systems only or specially listed dry systems. • Follow manufacturer'hs recommendations for freeze protection. • Allow for movement due to expansion and contraction. • Renew your BlazeMaster CPVC pipe and fittings installation training every two years. • Follow manufacturer's recommendations on pressure testing. • Follow current NFPA standards for use of antifreeze solutions. Blazemaster® is a registered trademark of Lubrizol Teflon® is a registered trademark of E. I. du Pont de Nemours and Company Crisco® is a registered trademark of the J.M. Smucker Company Regional Headquarters Don'ts Iff Do not use petroleum or solvent -based paints, sealants, lubricants or fire stop materials. • Do not use any glycol -based solutions as an anti -freeze. • Do not use both Teflon® tape and thread sealants simultaneously. • Do not use solvent cement that exceeds its shelf life or has become discolored or gelled. • Do not allow solvent cement to plug the sprinkler head orifice. • Do not connect rigid metal couplers to BlazeMaster® CPVC grooved adapters. • Do not thread BlazeMaster CPVC pipe. • Do not use solvent cement near sources of heat, open flame, or when smoking. • Do not pressure test until recommended cure times are met. • Do not use dull or broken cutting tool blades when cutting pipe. • Do not use BlazeMaster CPVC pipe that has been stored outdoors unprotected and is faded in color. • Do not allow threaded rod to come in contact with the pipe. • Do not install BlazeMaster CPVC pipe in cold weather without allowing for expansion. • Do not install BlazeMaster CPVC pipe and fittings in dry systems, unless specifically Listed for such use. • Do not use ratchet cutters below 50•F. • Do not use edible oils such as Crisco® as a gasket lubricant. • Do not install tape, insulated wire, or cable in direct contact with BlazeMaster CPVC pipe. Note:This list does not constitute as a complete installation guide. Viking SupplyNet - U.S. East Viking SupplyNet - U.S. Midwest Viking SupplyNet - U.S. West 4B Cranberry Rd 2353 International St 9101 Sorensen Ave. Parsippany, NJ 07054 Columbus, OH 43228 Santa Fe Springs, CA 90670 Phone: 800-845-4645 Phone: 800-926-7757 Phone: 800-366-1727 Fax: 269-818-1639 Fax: 614-527-5818 Fax: 562-944-1058 Viking SupplyNet - U.S. South Viking SupplyNet - Latin America Viking SupplyNet - Canada 100 Piedmont Court, Suite A 2840 SW 42nd St, Port 95 Ind Ctr Blg IV 325 Vaughan Valley Blvd. Doraville, GA 30340 Hollywood, FL 33312 Woodbridge, Ontario L4H 3135 Phone:800-234-2443 Phone:954-791-1756 Phone:905-856-3557 Fax: 770-446-3713 Fax: 954-791-1614 Fax: 905-856-3558 WARNING: Cancer and Reproductive Harm- www.P65 Warnings.ca.gov May 2014 Viking 1 210 N Industrial Park Drive, Hastings, MI 49058,Telephone: (269) 945-9501, Facsimile: (269) 945-9599 1 www.vikinggroupinc.com MKT-1089 Page 1 of 5 FREEDOM° RESIDENTIAL CONCEALED PENDENT SPRINKLER VK494 (K4.9) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com 1. DESCRIPTION Viking Freedom") Residential Concealed Pendent Sprinkler VK494 is a small thermosensitive, glass -bulb residential sprinkler designed for installation on concealed pipe systems where the appearance of a smooth ceiling is desired. The orifice design, with a K-Factor of 4.9 (70.6 metric*), allows the sprinkler's efficient use of available water supplies for the hydraulically designed fire -protection system. The fast response glass bulb operating element and special deflector characteristics meet the challenges of residential sprinkler standards. The sprinkler is pre -assembled with a threaded adapter for installation with a low -profile small -diameter cover assembly installed flush to the ceiling. The two- piece design allows installation and testing of the sprinkler prior to installation of the cover plate. The "push -on", "thread -off' design of the concealed cover plate assembly allows easy installation of the cover plate after the system has been tested and the ceiling finish has been applied, while also providing up to 1/2" (13 mm) of vertical adjustment. The cover assembly can be removed and reinstalled, allowing temporary removal of ceiling panels without taking the sprinkler system out of service or removing the sprinkler. The Electroless Nickel PTFE (ENT) coating has been investigated for installation in corrosive atmospheres and is C-UL- US-EU Listed as corrosion resistant as indicated in the Approval Charts. The ENT finish is only available for the sprinkler assembly, the cover plate is not plated. 2. LISTINGS AND APPROVALS e@us UL Listed (C-UL-US-EU): Category VKKW eu Refer to the Approval Charts and Design Criteria on for C-UL-US-EU Listing requirements that must be followed. TECHNICAL DATA Specifications: Minimum Operating Pressure: Refer to the Approval Chart. Maximum Working Pressure: 175 psi (12 bar). Factory tested hydrostatically to 500 psi (34.5 bar). Thread size: 1/2" (15 mm) NPT Nominal K-Factor: 4.9 U.S. (70.6 metric*) Glass -bulb fluid temperature rated to -65 °F (-55 °C) * Metric K-factor measurement shown is in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. Material Standards: Sprinkler Body: Brass UNS-C84400 or QM Brass Deflector: Phosphor Bronze UNS-051000 Deflector Pins: Stainless Steel UNS-S30200 Button: Brass UNS-C36000 Pip Cap and Insert Assembly: Copper UNS-C11000 and SS UNS-S30400 Compression Screw: 18-8 Stainless Steel Yoke: UNS-S43000 Stainless Steel or Phosphor Bronze UNS-051000 Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape Cover Adapter: Cold Rolled Steel UNS-G10080, Finish: Clear Chromate over Zinc Plating Shipping Cap: Polyethylene Cover Plate Materials: Cover Plate Assembly: Copper UNS-C11000 and Brass UNS-C26800 Spring: Beryllium Nickel Solder: Eutectic Ordering Information: (Also refer to the current Viking price list.) Viking Freedom° Residential Concealed Pendent Sprinkler VK494 and Cover Plate Assembly must be ordered separately: Sprinkler: Order Sprinkler VK494 by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A and ENT = JN Temperature Suffix: 155 °F (68 °C) = B, 200 °F (93 °C) = E For example, sprinkler VK494 with a Brass finish and a 200 °F (93 °C) temperature rating = Part No. 20759AE. Cover Plate Assembly: Base Part No. 13504 (2-3/4" diameter), Base Part No. 13642 (3-5/16" diameter), or Base Part No. 15394 (square cover plate, 3-5/16" diameter) Form No. F_012116 17.04.20 Rev 17.2 Replaces Form No. F_012116 Rev 17.1 (added alt. material for yoke) Page 2 of 5 FREEDOM° RESIDENTIAL CONCEALED PENDENT SPRINKLER VK494 (K4.9) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com Specify finish and temperature rating of the cover plate assembly by adding the appropriate suffixes for the finish and the cover temperature rating to the base part number: Finish Suffix: Polished Chrome = F, Brushed Chrome = F-/B, Bright Brass = B, Antique Brass = B-/A, Brushed Brass = B-/B, Brushed Copper = E-/B, Painted White = M-/W, Painted Ivory = MA, Painted Black = M-/B Temperature Suffix: 135 °F/57 °C = A For example, cover 13504 with a Polished Chrome finish and a 135 °F/57 °C temperature rating = 13504FA. Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the Viking website.) Sprinkler Wrenches": A. Heavy Duty Part No. 14047W/B** (available since 2006), or B. Head Cabinet Wrench Part No. 14031 *** (available since 2006) C. Optional Concealed Cover Plate Installer Tool Part No. 14412 (available since 2007) D. Optional Large Concealed Cover Plate Installer Tool Part No. 14867 (available since 2007) **Requires a ''/2' ratchet (not available from Viking). ***Also optional for removal of the protective cap. Ideal for sprinkler cabinets. Sprinkler Cabinet: Part No. 01731A (available since 1971) 4. INSTALLATION Refer to appropriate NFPA Installation Standards. 5. OPERATION During fire conditions, when the temperature around the sprinkler approaches its operating temperature, the cover plate detaches, releasing the deflector. Continued heating of the exposed sprinkler causes the heat -sensitive liquid in the glass bulb to expand, causing the glass to shatter, releasing the yoke and pip cap and sealing spring assembly.. Water flowing through the sprinkler orifice strikes the deflector, forming a uniform spray pattern over a specific area of coverage determined by the water supply pres- sure at the sprinkler to extinguish or control the fire. 6. INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. 7. AVAILABILITY Viking Sprinkler Model VK494 is available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. 8. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Sprinkler Maximum Temperature Rating Cover Large Square Temperature Nominal Ambient of the Cover Plate Cover Plate Cover Plate Bulb Color Classification Temperature Ceiling Assembly Base Part Base Part Base Part Rating' Temperature2 (Required)' Number° Number° Number° Ordinary 155 °F (68 °C) 100 °F (38 °C) 135 °F (57 °C) 13504 13642 15394 Red Intermediate 200 °F (93 °C) 150 °F (65 °C) 135 °F (57 °C) 13504 13642 15394 Green Sprinkler Finishes: Brass and ENT Cover Plate Finishes: Polished Chrome, Brushed Chrome, Bright Brass, Antique Brass, Brushed Brass, Brushed Copper, Painted White, Painted Ivory, or Painted Black Corrosion Resistant Coatings5: ENT Footnotes The sprinkler temperature rating is stamped on the deflector. 2 Based on NFPA-13, NFPA 13R, and NFPA 13D. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. Maximum ambient temperature for cover assembly is 100 °F (38 °C). ° Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. The corrosion resistant coatings have passed the standard corrosion test required by the approving agencies indicated in the Approval Charts. These tests cannot and do not represent all possible corrosive environments. Prior to installation, verify through the end -user that the coatings are compatible with or suitable for the proposed environment. For automatic sprinklers, the ENT coating is applied to all exposed exterior surfaces, including the waterway. For ENT coated sprinklers, the Belleville spring is exposed. Form No. F_012116 17.04.20 Rev 17.2 Page 3 of 5 FREEDOM° RESIDENTIAL CONCEALED PENDENT SPRINKLER VK494 (K4.9) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com Approval Chart Viking VK494, 4.9 K-Factor Residential Concealed Pendent Sprinkler For systems designed to NFPA 13D or NFPA 13R. For systems designed to NFPA 13, refer to the design criteria. For Ceiling types refer to current editions of NFPA 13, 13R or 13D Sprinkler Base NPT Thread Size Nominal K-Factor Maximum Water Wor- Part Number 1 SIN king Pressure Inches mm U.S. metric 2 20759 VK494 1/2 15 4.9 70.6 175 psi (12 bar) Max. Coverage 6 Flow GPM Pressure Listings and Minimum Area (LPM) PSI(bar) Deflector to Installation Approvals3,s Spacing Ceiling Type Ft. 155 °F (68 °C), 200 °F (93 °C) Temperature ` p °S Ft. X Ft. (m) (m X m) Rated Sprinklers Eo 12 X 12 13 7.0 (3.7 X 3.7) (49.2) (0.48) 14 X 14 13 7.0 (4.3 X 4.3) (49.2) (0.48) Refer to Figure 2 Concealed with Cover Plate See Footnotes 7,10, & 11 8 16 X 16 13 7.0 (4.9 X 4.9) (49.2) (0.48) Assembly. See Footnote 9. (2.4) 18 X 18 17 12.0 (5.5 X 5.5) (64.4) (0.83) 20 X 20 20 16.7 (6.1 X 6.1) (75.7) (1.15) Footnotes Part number shown is the base part number. For complete part number, refer to current Viking price schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. Refer also to Design Criteria. 4 Listed by Underwriter's Laboratories, Inc. for use in the U.S., Canada, and European Union. 5 Meets New York City requirements, effective July 1, 2008. 6 For areas of coverage smaller than shown, use the "Flow' and "Pressure" for the next larger area listed. Flows and pressures listed are per sprinkler. The distance from sprinklers to walls shall not exceed one-half the sprinkler spacing indicated for the minimum "Flow' and "Pressure" used. Cover Temperature Rating is 135 °F (57 °C). Cover Part No. 135041, 136421 (large diameter), or 15394' (square cover plate). 9 Other paint colors are available on request with the same listings as the standard finish colors. Listings and approvals apply for any paint manufacturer. Contact Viking for additional information. Custom colors are indicated on a label inside the cover assembly. Refer to Figure 3. 0 Accepted Cover Plate Finishes are: Polished Chrome, Brushed Chrome, Bright Brass, Antique Brass, Brushed Brass, Brushed Copper, Painted White, Painted Ivory, or Painted Black 1. " C-UL-US-EU Listed as corrosion resistant - Electroless Nickel PTFE (ENT) Form No. F_012116 17.04.20 Rev 17.2 Page 4 of 5 FREEDOM° RESIDENTIAL CONCEALED PENDENT SPRINKLER VK494 (K4.9) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com DESIGN CRITERIA (Also refer to the Approval Chart on page 3.) UL Listing Reguirements (C-UL-US-EU): When using Viking Residential Concealed Pendent Sprinkler VK494 for systems designed to NFPA 13D or NFPA 13R, apply the listed areas of cover- age and minimum water supply requirements shown in the Approval Chart. For systems designed to NFPA 13: The number of design sprinklers is to be the four contiguous most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the following: • The flow rates given in the Approval Chart for NFPA 13D and NFPA 13R applications for each listed area of coverage, or • Calculated based on a minimum discharge of 0.1 gpm/sq. ft. over the "design area" in accordance with sections 8.5.2.1 or 8.6.2.1.2 of NFPA 13. • Minimum distance between residential sprinklers: 8 ft. (2.4 m). NOTE: Concealed sprinklers must be installed in neutral or negative pressure plenums only. IMPORTANT. Always refer to Bulletin Form No. F 080415 - Best Practices for Residential Sprinkler Handling and Installation. Also refer to Form No. F 080614 for general care, installation, and maintenance information. Viking sprinklers are to be in- stalled in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA and any other similar Authorities Having Jurisdiction, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Final approval and acceptance of all residential sprinkler installations must be obtained from the Authorities Having Jurisdiction. Sprinkler and Adapter Assembly • Protective cap removed • Use wrench 14047W/B** Sprinkler Wrench Part No. 14047W/B** Step 1: Carefully slide the wrench sideways around the deflector and pins NEVER install the sprinkler by applying the installation wrench across the frame arms. DO NOT overtighten. Use only the designated sprinkler wrenches, Viking Part Numbers 14047W/B** or 14031**. A leak tight seal should be achieved by turning the sprinkler clockwise 1 to 1-1/2 turns beyond finger tight. 2-1/4" (57 mm) diameter opening required in the ceiling. Step 2: 1 1 Carefully press the wrench upward and turn slightly to ensure engagement with the sprinkler wrench flats. Sprinkler wrench flat Figure 1: Sprinkler Installation and Proper Wrench Usage ** A 1/2" ratchet is required (Not available from Viking) Sprinkler frame arms Form No. F_012116 17.04.20 Rev 17.2 Page 5 of 5 FREEDOM° RESIDENTIAL CONCEALED PENDENT SPRINKLER VK494 (K4.9) The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page www.vikinggroupinc.com 1/2" (15 mm) NPT E N co S 2-9/16" (65 mm) Maximum NOTE: Upon sprinkler activation, the deflector descends to approximately 13116" (21 mm) below the sprinkler body. 2-1/16" (52 mm) Minimum Figure 2: Sprinkler Dimensions and Cover Installation QQ�\�--p C USTO�A a �2 O C) v� O VIKING0. All custom color painted cover plates will have an identifying label affixed to the inside of the cover that indicates the custom color and will have a representative sample (a paint dot) of the paint on the label. Figure 3: Identification of Custom Paint for Concealed Covers 2-3/4" (70 mm) or 3-5/16" (84 mm) - -1 - \- . .... ., Figure 4: Square Cover Assembly 15394 Form No. F_012116 17.04.20 Rev 17.2 Replaces Form No. F_012116 Rev 17.1 (added alt. material for yoke) Page 1 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I KJ SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com 1. DESCRIPTION Viking Quick Response Dry Horizontal Sidewall Sprinklers are thermosensitive spray sprinklers suitable for use in areas subject to freezing. The sprinklers are designed for dry systems and preaction systems where it is necessary to prevent water or condensation from entering the drop nipple before sprinkler operation. They may also be installed in spaces subject to freezing and supplied from a wet system in an adjacent heated area. Viking Quick Response Dry HSW Sprinklers are available in various finishes and temperature ratings to meet design requirements. The special Polyester and AL Electroless Nickel PTFE (ENT) coatings have been investigated for installation in corrosive atmospheres and are listed/approved as corrosion resistant as indi- cated in the Approval Charts. (Note: FM Global has no approval classification for Polyester coatings as corrosion resistant.) 2. LISTINGS AND APPROVALS cULus Listed: Category VNIV FM Approved: Classes 2013 and 2015 For Light Hazard Occupancies Only M, NYC Approved: MEA 89-92-E, Volume 15 Refer to Approval Charts and Design Criteria for Listing and Approval that must be followed. 3. TECHNICAL DATA Specifications: Available since 1993. WARNING: Cancer and Reproductive Harm - Minimum Operating Pressure: 7 psi (0.5 bar) Zt www.P65Warnings.ca.gov Maximum Working Pressure: 175 psi (12 bar). Factory tested hydrostatically to 500 psi (34.5 bar) Thread size: 1" NPT or 25 mm BSPT Nominal K-Factor: 5.6 U.S. (80.6 metric') for all listed and approved lengths. Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. Glass -bulb fluid temperature rated to -65 °F (-55 °C) Covered by the following U.S. Patent numbers: 8,636,075 and 8,376,060 and 10,220,231 Material Standards: Frame Casting: Brass UNS-C84400 Deflector: Phosphor Bronze UNS-051000 Bulb: Glass, nominal 3 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE Tape Compression Screw: Brass UNS-C36000 Pip Cap: Brass UNS-C31400 or UNS-C31600 Pip Cap Adapter: Brass UNS-C36000 Orifice: Copper UNS-C22000 or UNS-C11000 Tube: ERW Hydraulic Steel Tube Support (Internal): Stainless Steel UNS-S30400 Barrel: Steel Pipe UNS-G10260, Electrodeposited Epoxy Base finish Barrel End and Threads: QM Brass Sleeve (for Adjustable Standard style only): Brass UNS-C26000 or UNS-C26800 Escutcheon Materials: Adjustable Standard Dry Escutcheons: Brass UNS-C26000 or UNS-C26800 Recessed Dry Escutcheons: Cold Rolled Steel UNS-G10080 ENT Coated Adjustable and Recessed Escutcheons: Stainless Steel UNS-S30400 Ordering Information: (Also refer to the current Viking price list.) Order QR Dry HSW Sprinklers by first adding the appropriate suffix for the sprinkler finish, the appropriate suffix for the temperature rating, and then the suffix for the length ("A" dimension) to sprinkler base part number. Order in a specific length noted as the "A" dimension. The "A" dimension is the distance from the face of the fitting (tee) to the desired finished surface of the wall in which it is to be installed. These sprinklers are listed and approved in lengths from 1-1/2" to 45-1/2" (38.1 mm to 1,156 mm) for the adjustable standard style, 3" to 47" (76.2 mm to 1,194 mm) for the plain barrel style, and 3-1/4" to 47-1/2" (82.5 mm to 1,207 mm) for the adjustable recessed style. Lengths exceeding the standard lengths are available, with no approvals, on a "made -to -order" basis: Recessed Dry HSW up to 65- 1/2" (1,664 mm). Adjustable Standard Dry HSW up to 63-1/2" (1,613 mm). Plain Barrel Dry HSW up to 65" (1,651 mm). Contact the manufacturer for more information. Finish Suffix: Brass = A, Chrome = F, White Polyester = M-NV, and ENT = JN Form No. F_031993 20.04.16 Rev 20.1 Replaces Form No. F_031993 Rev 19.2 (Removed cover 15610.) Page 2 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I KJ SIDEWALL SPRINKLERS 4 P 6 7 The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Temperature Suffix: 155 °F (68 °C) = B, 175 °F (79 °C) = D, 200 °F (93 °C) = E, 286 °F (141 °C) = G Escutcheon Suffix = Y for the adj. recessed sprinkler with the Model G-1 Escutcheon (no suffix needed for the Model E-1 Escutcheon). For example, sprinkler VK182 with 1" NPT Threads, a Chrome finish, a 155 °F (68 °C) temperature rating, the Model G-1 Escutcheon, and "A" length of 10" = Part No. 08386UFBY10. Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the "Sprinkler Accessories" section.) Sprinkler Wrenches: A. Standard Wrench: Part No. 07297W/B (available since 1991) B. Wrench for recessed sprinklers: Part No. 07565W/B** (available since 1991) **A'/i' ratchet is required (not available from Viking). Replacement Escutcheons: A. Adjustable Standard Dry Escutcheon: Base Part No. 08086F B. Model E-1 Recessed Dry Escutcheon Cup: Base Part No. 05459A C. Model G-1 Recessed Dry Escutcheon Cup: Base Part No. 20133 INSTALLATION Refer to appropriate NFPA Installation Standards. OPERATION During fire conditions, the heat -sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the internal parts to open the water- way. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. Sprinkler s eo s Jeways clarltyCRef�r rjure : r-/ correct defector orlentatlonJ INSPECTIONS, TESTS AND MAINTENANCE Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. Figure 1: AVAILABILITY Standard Sprinkler Wrench 07297W/B The Viking Quick Response Dry Horizontal Sidewall Sprinkler is available through a network of domestic and international distribu- tors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. 8. GUARANTEE For details of warranty, refer to Viking's current list price schedule or contact Viking directly. TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Temperature Sprinkler Nominal Maximum Ambient Bulb Color Classification Temperature Rating' CeilingTemperature2 Ordinary 155 °F (68 °C) 100 °F (38 °C) Red Intermediate 175 °F (79 °C) 150 °F (65 °C) Yellow Intermediate 200 °F 93 °C 150 °F 65 °C Green High 286 °F 141 °C 225 °F 107 °C Blue Sprinkler Finishes: Brass, Chrome, White Polyester, and ENT Corrosion -Resistant Coating3,4: White Polyester and ENT in all temperature ratings Footnotes ' The sprinkler temperature rating is stamped on the deflector. 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. 3 The corrosion -resistant Polyester and ENT coatings have passed the standard corrosion test required by the approving agencies indi- cated in the Approval Charts. These tests cannot and do not represent all possible corrosive environments. Note: These coatings are NOT corrosion proof. Prior to installation, verify through the end -user that the coatings are compatible with or suitable for the proposed environment. Polyester and ENT coatings are applied to the exposed exterior surfaces only. Note that the spring is exposed on sprinklers with Polyester and ENT coatings. " When installed in some corrosive environments, the Polyester finish may change color. This natural discoloration over time is not in itself an indication of corrosion and should not be treated as such. All sprinklers installed in corrosive environments should be replaced or tested as described in NFPA 25 on a more frequent basis. Form No. F_031993 20.04.16 Rev 20.1 Page 3 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I KJ SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com �i )K*Notei A 1/2" ratchet is required, Sprinkler Wrench Part (Not available from Viking) No 07565W/B)K)K for installing recessed dry sprinklers. -------------- (^ i_ ____ _________T_ j I ' 1 Step 1: Carefully slide the Step 2: Press the wrench onto wrench sideways around the J the sprinkler wrench flats and deflector and protective turn slightly to ensure engage - shield as shown ment with the wrench flats. Figure 2: Wrench 07565W/B for Adjustable Recessed Dry Horizontal Sidewall Sprinklers For 'A" Dimension: 1. Determine the distance from the face of TFFFT the tee to the finished face of the wall, 2. Round to the nearest 1/2' (12.7 mm) between 1-1/2' (38.1 mm) and 45-1/2' (1,156 mm). NOTE: The deflector will extend approximately 4-1/8' (104.8 mm) from the wall with 2' +/- 1' (25.4 mm) horizontal adjustment available. �A Minimum wall opening J diameter: 1-3/4' (44.5 mm). Maximum wall opening diameter) 2-1/4' (57 mm), mummmmmumnaw Deflector at Minimum Distance - Finished Ceiling From Wall Finished Wall 4' (102 mm) Minimum 6' (152 mm) Maximums 1 (79.4 mm) 17 3-1/16" l (77,8 mm) � / 5/8' (15,9 ` 1 Sleeve diameter) 1-1/2' (38.1 mm). -13/16' Sleeve finish matches )K (20.6 mm) finish of escutcheon. NOTE1 To locate the deflector at the minimum distance from the wall, with no adjustment available, order the standard dry horizontal sidewall sprink- ler 1' (25.4 mm) shorter than the 'A' Dimension. Deflector at NOTE Maximum Distance To locate the deflector From Wall at the maximum distance from the wall, with no adjustment available, order the standard dry horizontal sidewall sprink- ler 1' (25.4 mm) longer than the 'A' Dimension. May be allowed up to 18' (457 mm) for certain FM installations. Refer to the appropriate installation standards, including NFPA 13 and/or FM Loss Prevention Data Sheet 2-0. Figure 3: Adjustable Standard Dry Horizontal Sidewall Sprinkler Slot Deflector _ Slot Push and Rotate Sleeve STEP 1: Align the slot in STEP 2: Push the rounded STEP 3: Pull the escutcheon STEP 4: Push and rotate STEP 5: To minimize the escutcheon with the end of the slot against the away from the near edge the escutcheon onto the visibility of the slot horizontal surface of near edge of the deflector. of the deflector. Move the sleeve, in the escutcheon, the deflector as shown. Push the far side of the near side of the escut- position the slot escutcheon past the deflec- cheon over the deflector, at the top of the Tor, toward the sleeve, sprinkler sleeve. Figure 4: Adjustable Standard Escutcheon Installation Form No. F_031993 20.04.16 Rev 20.1 Page 4 of 8 ® QUICK RESPONSE DRY HORIZONTAL SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart 1 (UL) Temperature KEY Quick Response Dry Horizontal Sidewall Sprinklers Finish For Light Hazard Occupancies Only AIX *- Escutcheon (if applicable) Maximum 175 PSI (12 bar) WWP Sprinkler Base Thread Size Nominal Order Length Listings and Approvals' Part No.' SIN Style K-FactorZ Increment (Refer also to Design Criteria on page 106e.) NPT BSPT U.S. metric' Inches mm cULus' NYC6 VdS LPCB (E Ci 08384U VK178 Adjustable Standard 1" -- 5.6 80.6 1/2" 12.7 A1, A5 Al -- -- -- - 16458U -- 25 mm -- 80.6 1/2" 12.7 A1, A5 08386U VK182 Adjustable Recessed 1" -- 5.6 80.6 1/4" 6.35 B2, B6 B2 -- -- - 16454U -- 25 mm -- 80.6 1/4" 6.35 B2, B6 - -- -- 08388U VK174 Plain Barrel ill -- 5.6 80.6 1/2" 12.7 A3 A4 -- -- 16456U 25 mm -- 80.6 1/2" 12.7 A3 Approved Finishes and "A" Dimensions 1* - Chrome, or White Polyester' sprinkler with a Chrome, Brass, or White Polyester Sleeve and Escutcheon with "A" dimensions 1-1/2" to 45-1/2" (38.1 mm to 1,156 mm) Approved Temperature Ratings 2* - Chrome, or White Polyester' with "A" dimensions 3-1/4" to 47-1/2" (82.5 mm to 1,207 mm) A - 155 -F (68 -C), 175 -F (79°C), 200 -F 3 - Chrome, Brass, White Polyester', or ENT' with "A" dimensions 3" to 47" (76.2 mm to 1,194 mm) (93 °C), and 286 °F (141 °C) 4 - Chrome or Brass with "A" dimensions 3" to 47" (76.2 mm to 1,194 mm) B - 155 °F (68 °C), 175 °F (79 °C), and 5 - ENT' sprinkler with an ENT' Sleeve and Escutcheon with "A" dimensions 1-1/2" to 45-1/2" (38.1 200 -F (93 -C) mm to 1,156 mm) 6 - ENT' with "A" dimensions 3-1/4" to 47-1/2" (82.5 mm to 1,207 mm) *Brass Finish is listed and approved but not standard offering, lead times of 6-8 weeks required. (Matching Brass escutcheons are not available.) Footnotes ' Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 K-Factor applies for standard lengths ("A" Dimensions indicated above). 3 Metric K-factor shown is for use when pressure is measured in bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. 4 This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. 5 Listed by Underwriter's Laboratories for use in the U.S. and Canada for Light Hazard occupancies only. 6 Accepted for use, City of New York Department of Buildings, MEA Number 89-92-E, Vol. 15. ' cULus Listed as corrosion resistant. DESIGN CRITERIA - UL (Also refer to Approval Chart 1 above.) cULus Listing Reguirements: Quick Response Dry Horizontal Sidewall Sprinklers are cULus Listed as indicated in Approval Chart 1 for installation in accordance with the latest edi- tion of NFPA 13 for standard spray sprinklers. • Limited to Light Hazard occupancies only. • Protection areas and maximum spacing shall be in accordance with the tables provided in NFPA 13. • Minimum spacing allowed is 6 ft. (1.8 m). • Deflector must be positioned between 4" and 6" (102 mm and 152 mm) below the ceiling. Keep the top of the deflector oriented parallel with the ceiling. • Locate no less than 4" (102 mm) from end walls. • Maximum distance from end walls shall be no more than one-half of the allowable distance between sprinklers. The distance shall be measured perpendicular to the wall. • The sprinkler installation and obstruction rules contained in NFPA 13 for sidewall standard spray sprinklers must be followed. IMPORTANT. Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_031993 20.04.16 Rev 20.1 Page 5 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I KJ SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com Approval Chart 2 (FM) Temperature KEY Quick Response Dry Horizontal Sidewall Sprinklers Finish For Light Hazard Occupancies Only AlXFEscutcheon (if applicable) Maximum 175 PSI (12 bar) WWP Sprinkler Base Thread Size Nominal K-Factor2 Order Length Increment FM Approvals° Part No. SIN Style (Refer also to Design Criteria below.) NPT BSP U.S. metric' Inches mm 08384U VK178 Adjustable Standard 1" - 5.6 80.6 1/2" 12.7 Al 16458U -- 25 mm -- 80.6 1/2" 12.7 Al 08386U VK182 Adjustable Recessed 1" -- 5.6 80.6 1/4" 6.35 B2 16454U -- 25 mm -- 80.6 1/4" 6.35 B2 08388U VK174 Plain Barrel 1" -- 5.6 80.6 1/2" 12.7 A3 16456U - 25 mm -- 80.6 1 1/2" 12.7 A3 Approved Finishes and "A" Dimensions 1" - Bright Brass, Chrome, White Polyester, or ENT5 with "A" dimensions 1-1/2" to 45-1/2" (38.1 Approved Temperature Ratings mm to 1,156 mm) 2' - Bright Brass, Chrome, White Polyester, or ENT' with "A" dimensions 3-1/4" to 47-1/2" (82.5 A- 155 °F (68 °C), 175 °F (79 °C), 200 °F (93 °C), and mm to 1,207 mm) 286 °F (141 °C) 3 - Brass, Bright Brass, Chrome, White Polyester, or ENT' "A" dimensions 3" to 47" (76.2 mm to B - 155 °F (68 °C), 175 °F (79 °C), and 200 °F (93 °C) 1,194 mm) "Brass Finish is listed and approved but not standard offering, lead times of 6-8 weeks required. (Matching Brass escutcheons are not available.) Footnotes Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 K-Factor applies for standard lengths ("A" Dimensions indicated above). 3 Metric K-factor shown is for use when pressure is measured in bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0. ° This chart shows the FM Approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. 5 FM approved as corrosion resistant. DESIGN CRITERIA - FM (Also refer to Approval Chart 2 above.) FM Approval Reauirements: The Dry HSW Sprinklers in the Approval Chart above are FM Approved as quick response Non -storage standard spray sprinklers as indicated in the FM Approval Guide. For specific application and installation requirements, reference the latest applicable FM Loss Prevention Data Sheets (including 2-0) and Technical Advisory Bulletins. FM Global Loss Prevention Data Sheets and Technical Advisory Bulletins contain guidelines relating to, but not limited to: minimum water supply requirements, hydraulic design, ceiling slope and obstructions, minimum and maximum allowable spacing, and deflec- tor distance below the ceiling. NOTE: The FM installation guidelines may differ from cULus and/or NFPA criteria. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to Form No. F_080614 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accord- ance with the latest edition of Viking technical data, the appropriate standards of NFPA, FM Global, LPCB, APSAD, VdS or other similar organizations, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Form No. F_031993 20.04.16 Rev 20.1 Page 6 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I KJ SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com For 'A' Dimenslorr 1, Determine the distance from the face of the tee to the face of the finished wall. 2. Round to the nearest 1/4' (6.35 mm) between 3-1/4' (83 mm) and 47-1/2' (1,207 mm). NOTF The sprinkler will be recessed approximately 5/16' (7,9 mm) with 5/8' (16 mm) horizontal adjustment available F� A II Minimum wall opening I II vi 2-1/8' (54 mm) diameter. Maximum wall opening 2-1/2' (63.5 mm) diameter, w May be allowed up to 18' (457 mm) for certain FM installations. Refer to the appropriate Installation standards, including NFPA 13 and/or FM Loss Prevention Data Sheet 2-0 Ceiling Wall —7 4' (102 mm) Minimum 6' (152 mm) Maximum* 5/8' (16 mm) 3-1/16' (77.8 mm) Available Adjustment 1-23/32' (43.7 mm) Minimum 2-11/32' (59,5 mm) Maximum 5/16' (7,9 mm) Outward Adjustment 5/16' (73 mm) Inward Adjustment Figure 5: Adjustable Recessed Dry Horizontal Sidewall Sprinkler with the Model E-1 Escutcheon Side outlet of �\ Tee turned to req'd angle for slope of ceiling Adjustable Adapter Ring Depth, 1-1/16' (27 mm) 1/8' (3.2 mm) Adjustable Outer Cup 2-5/8' 4- (66 ) (102 mm) mm Figure For 'A' Dlmenslorr 1. Measure B Dimension from centerline of the face of the tee to the horizontal centerline of the wall opening. 2. Measure C Dimension from the centerline of the Face of the tee to the finished wall q 3. Calculate 'A' Dimension using; A = ++ C NOTE, A Dimension will provide approximately 1/4' of adjustment in either direction. Ceiling Deflector distance �4-6' (102 to 152 mm) "�Lr%�below the ceiLing,)K Minimum wall openingi When measuring for 2-5/8' (66 mm) diameter, the 'A' Dimension, Maximum wall opening: the exact deflector 3-3/4' (95 mm) diameter. .--Wall distance below the ceiling must be known. C 3( May be allowed up to 18' (457 mm) for certain FM Installations. Refer to the appropriate installation standards, including NFPA 13 and/or FM Loss Prevention Data Sheet 2-0. Adjustable Recessed Dry Horizontal Sidewall Sprinkler with the Model G-1 Escutcheon Form No. F_031993 20.04.16 Rev 20.1 Page 7 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I Ki SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com For "A" Dimension 1, Determine the distance from the face of the tee to the base of the sprinkler. 2 Round to next highest 1/2' (12.7 mm) increment, between 3" (76.2 mm) and 47' (1,194 mm). A Outside diameter; 1-5/16' (33A mm), (Same as 1" (25 mm) Schedule 40 pipe Ceiling Wall 7 4" (102 mm) Minimum 6" (152 mm) Maximumx 2-3/16" (51 mm)1 =47�1 5/8" (16 mm) .Be not exceed 6" (152 mm), Do not recess wrench boss. x May be allowed up to 18' (457 mm) for certain FM installations, Refer to the appropriate installation standards, including NFPA 13 and/or FM Loss Prevention Data Sheet 2-0. Figure 7: Quick Response Plain Barrel Dry Horizontal Sidewall Sprinkler Form No. F_031993 20.04.16 Rev 20.1 Page 8 of 8 ® QUICK RESPONSE DRY HORIZONTAL N4 I KJ SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com 5-1/8" a (130.2 mm)—1 Seal the clearance space around the sprinkler barrel to avoid ii ii ii Maximum leakage of air Into the protected area and consequent formation of condensate around the sprinkler frame, which could inhibit -- operation or cause premature operation. Refer to Figure 9, I If humidity and temperature differential causes condensation on the exposed dry sprinkler barrel, consider wrapping the exposed barrel with insulation, foam Insulating tape, or equivalent Install the 1" NPT threaded end of the dry sldewall sprink- ler into the 1" NPT outlet of a malleable iron tee fitting per ANSI B 16,3 (C(ass 150) or cast Iron threaded tee fitting per ANSI 16,4 (Class 125) only, Minimum wall opening: diameter: 1-3/4' (445 mm) Maximum wall opening (Exposed diameter: 2-1/4' (57 mm),Barrel) Ambient xpcsec Barre Ambient Temperature Temperature 40°F/4°C 50'F/l0°C 60'F/16°C of Protected Area## at the Ex p osed Minimum Barrel Discharge End Lengthy■ Face of the of the Sprinkler Tee to the Outer Surface of the Wall In. (mm) In. (mm) In. (mm) 40'F WC) 0 0 0 30'F (-1'0 0 0 0 20'F (-7'C) 4 (100) 0 0 10'F (-12'C) 8 (203) 1 (25.4) 0 0'F (-18'C) 12 (305) 3 (76) 0 -10'F (-23'C) 14 (356) 4 (102) 1 (25.4) -20'F (-29'C)14 (356) 6 (152) 3 (76) -30'F (-34'C) 16 (406) 8 (203) 4 (102) -40'F (-40'C) 18 (457) 8 (203) 4 (102) -50-F (-46'C) 20 (508)10 (254)6 (152) -60-F (-51'C) 20 (508) 10 (254) 6 (152) NOTE To locate the II II II------------------- Deflector at deflector at the IIIIIIIII__________________= Maximum Distance From Wall maximum distance from IIIIIIIII------------------ the wall, with no IIIIIIIII IIIIIIIII 13/16" adjustment available, IIIIIIIII (20.6 mm) Ceiling order the standard IIIIIIIII or horizontal side-4' (102 mm) Minimum wall sprinkler 1" 6' (152 mm) Maximum)K longer than the "A" Sleeve finish matches dimension. escutcheon Up to 2' (50.8 mm) 3-1/16" adjustment is available, (77.8 mm) - 5/8" - (15.9 mm) 3-1/8' (79.4 mm) Minimum 1-1/2' NOTE To locate the (38.1 mm) diameter n ii ii deflector the minimum distance from Outer the wall, with no Surface adjustment available, of the Wall _ order the standard dry horizontal side- ;; wall sprinkler 1" Deflector at shorter than the Minimum Distance From Wall 'A' dimension. #May be allowed up to 18' (457 mm) for certain FM installations. Refer to the appropriate installation standards, including NFPA 13 and/or FM Loss Prevention Data Sheet 2-0. �#The protected area refers to the area below the ceiling, The ambient temperature is the temperature at the discharge end of the sprinkler, For protected area temperatures that occur between the values listed, use the next cooler temperature. #)KThe minimum required barrel length is not the some as the "A" dimension. Refer to Figures 3, 5, 6 and 7 for the "A" dimension. Exposed minimum barrel lengths are inclusive up to 30 mph wind velocities, Figure 8: Dry Horizontal Sidwall Sprinkler Required Minimum Barrel Length Based on Ambient Temperature in the Protected Area (Adjustable Standard Dry HSW Sprinkler is Shown) Figure y: Dry Sprinkler Seal (Adjustable Standard Dry NSW Sprinkler is Shown) Replaces Form No. F_031993 Rev 19.2 Form No. F_031993 20.04.16 Rev 20.1 (Removed cover 15610.) Fig. 23 - Hanger for CPVC Plastic Pipe Double Fastener Strap Type Size Range — 3/4" thru 3" CPVC pipe Material — Pre -Galvanized Steel Function — Intended to perform as a hanger/restrainer to support CPVC piping used in automatic fire sprinkler systems. Fig. 23 can be installed on the top, bottom or side of a beam. The Fig. 23 also functions as a restrainer to prevent the upward movement of the sprinkler head during activation. Approvals — Underwriters' Laboratories Listed in the USA (UL) and Canada (cUL) sizes 3/4" thru 2" to support fire sprinkler piping. May be installed in wood using fasteners supplied with product, or into minimum 20 gauge steel using (2) 1/4" x 1 " tek type screw. Meets and exceeds the requirements of NFPA 13, 13R and 13D. Features — Fig. 23 incorporates features which protect the pipe and ease installation. The flared edge design protects the CPVC pipe from any rough surface. It also incorporates snap restrain- ers allowing easier and faster installation. Easily attaches to the building structure using the two UL Listed hex head self thread- ing screws* furnished with the product. It is recommended that rechargeable electric drills fitted with a hex socket attachment be used as installation tools. No impact tools (such as a hammer) are allowed. Damage has been known to result from installations using impact type tools. No pre -drilling of a pilot hole in wood is required. Finish — Pre -Galvanized Order By — Figure number and pipe size * Hardened hex head self threading screw is furnished with the product and is the minimum fastener size acceptable. 1<C C UL US LISTED Dimensions • Weights CPVC Max. Hanger Fastener Hex Approx. Pipe Size A B C Spacing (Ft.) Head Size Wt./100 3/4 31/8 19/16 13/16 51/2 5/16 9 1 33/8 1 11/16 13/16 6 5/16 9 1 1/4 43/16 23/32 13/16 61/2 5/16 11 11/2 47/16 27/32 13/16 7 5/16 12 2 47/8 27/16 13/16 8 5/16 15 2112 109/32 211/16 13/16 Consult Factory 5/16 22 3 117/8 3 13/16 Consult Factory 5/16 25 OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 CUSTOMER SERVICE • 800.786.5266 i www.tolco.com Fig. 24 - Hanger for CPVC Plastic Pipe Double Fastener Strap Type - Side Mount Size Range — 3/4" thru 2" CPVC pipe Material — Pre -Galvanized Steel Function — Intended to perform as a hanger/restrainer to support CPVC piping used in automatic fire sprinkler systems. Can be installed on the top or on the bottom of a beam. The Fig. 24 can also function as a restrainer to prevent the upward movement of the sprinkler head during activation. Approvals — Underwriters' Laboratories Listed in the USA (UL) and Canada (cUL) to support fire sprinkler piping. May be installed in wood using fasteners supplied with product, or into minimum 20 gauge steel using (2) 1/4" x 1 " tek type screws. Meets and exceeds the requirements of NFPA 13, 13R and 13D. Features — Fig. 24 incorporates features which protect the pipe and ease installation. The flared edge design protects the CPVC pipe from any rough surface. Easily attaches to the building structure using the two UL Listed hex head self threading screws* furnished with the product. It is recommended that rechargeable electric drills fitted with a hex socket attachment be used as installation tools. No impact tools (such as a ham- mer) are allowed. Damage has been known to result from installations using impact type tools. No pre -drilling of a pilot hole in wood is required. Finish — Pre -Galvanized Order By — Figure number and pipe size * Hardened hex head self threading screw is furnished with the product and is the minimum fastener size acceptable. A' C& US usreo Dimensions • Weights CPVC Max. Hanger Fastener Hex Approx. Pipe Size A B C Spacing (Ft.) Head Size Wt./100 3/4 25/16 15/32 13/16 51/2 5/16 9 1 25/8 15/16 13/16 6 5/16 9 11/4 3 11/2 13/16 61/2 5/16 11 11/2 31/4 15/8 13/16 7 5/16 12 2 311/16 127/32 13/16 8 5/16 15 OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 m CUSTOMER SERVICE • 800.786.5266 www.tolco.com 0 9111111 om Fig. 28 - "Stand -Off" Hanger & Restrainer for CPVC Plastic Pipe Size Range — 3/4" through 2" Material — Carbon Steel, Pre -Galvanized Function — Designed to be used as a hanger and restrainer for CPVC piping where the "stand-off" design will ease installation by eliminating the need for wood blocking. Features: • Flared edge design protects CPVC pipe from any rough or abrasive surfaces. • Unique twist and lock design holds pipe firmly in place and allows retrofit type of installation. • The "Stand-Off'I design eliminates the need for wood block extension. • Can be installed on horizontal or vertical piping regardless of mounting surface orientation. • Attaches easily to wood structure with two hex head self -threading screws furnished with product. • Installs easily using rechargeable electrical driver with 5/16" extension socket eliminating impact tool damage to pipe. • Attaches easily to steel, minimum 18 gauge with (2) 1/4" x 1'I tek type self drilling tapping screws. • UL Listed as a hanger and a restrainer for fire sprinkler piping. Approvals — Underwriters' Laboratory Listed in the USA (UL) and Canada (cUL) to support automatic fire sprinkler systems. May be installed into wood using fasteners supplied with product, or into minimum 18 gauge steel using (2) 1/4" x 1 " tek type screws. Meets and exceeds the requirements of NFPA 13, 13R and 13D. Fig. 28 satis- fies the UL vertical restraint requirement where needed. UL Listed as a hanger and ver- tical restraint when installed on 3/8" composite wood material. Use two Fig. 27B Speed Nuts when used as a hanger and restraint. Use one Fig. 27B Speed Nut on the upper installed screw when used as a hanger only. Order by — Figure number and pipe size. Pat. # 7,455,268, Pat. # 7,832,248 FI G.27B (1) REQUIRED HIGH SIDE OFHANGER (2) HANGER APPLICATION HANGER R RESTRAINT APPLICATION FIG.2B FIG.28 FIG. FIG.28 FG� C &US LISTED Dimensions • Weights Pipe Approx. Size A B C Wt. 3/4 31/32 2 31/2 .180 1 35/16 23/1 6 31/2 .210 11/4 35/8 23/8 31/2 .225 11/2 4 21/2 31/2 .310 2 41/2 211/16 35/8 .340 OFFICE/MANUFACTURING FACILITY • 1375 SAMPSON AVE. • CORONA, CA 92879 • PH: 951.737.5599 • FAX: 951.737.0330 m CUSTOMER SERVICE • 800.786.5266 www.tolco.com ARGCO Fire Sprinkler Pressure Gauges u� 0-300 psi water FM 0-300 psi air 0-300 psi air/water Application: Fluid medium which does not clog connection port or corrode copper alloy. Specifically designed for the fire sprinkler industry. Size: 4" (100 mm) Accuracy ± 3/2/3% of span (ASME B40.1 Grade B) Working Range Steady: 3/4 of full scale value Fluctuating: 2/3 of full scale value Short time: full scale value Operating Temperature Ambient: -40OF to 140OF (-40°C to 60°C) Media: max. 140°F (+60°C) Approvals UL listed (UL-393) FM approved Meets NFPA 25 Standards Temperature Error Standard Scale Additional error when temperature changes from reference temperature of 680F PSI (20°C) +0.4% for every 18' F (10°C) rising or falling. Percentage of span. Standard Features Connection Material: copper alloy Lower mount (LM) - not available for 11/2" size 1/4" NPT limited to wrench flat area Bourdon Tube: Material: copper alloy C-type Movement: Copper alloy, silicone dampened Dia: White plastic with stop pin - black & red lettering Pointer: Black aluminum Case: Black polycarbonate E Window Acrylic, ultrasonically welded to case Standard Series • Type 110.10sp Order Options water air/water air 4` NF' The information contained herein is produced in good faith and is believed to be reliable but is for guidance only. ARGCO and its agents cannot assume liability or responsibility for results obtained in the use of its product by persons whose methods are outside or beyond our control. It is the user's responsibility to determine the suitability of any of the products, methods of use, or preparation prior to use, mentioned in our literature. It is the user's responsibility to observe and adapt such precautions as may be advisable for the protection of personnel and property in the handling and use of any of our products. FOR MORE INFORMATION CALL ARGCO AT 1-800-854-1015 OR LOG ONTO WWW.ARGCO.COM