61295802 DOH approval to proceed with workProject Comment Form
Project Information:
CRS#61295802
Swedish Hospital EdmondsProject Title:Medivator InstallationProject Location:21601 76th Ave WEdmonds, WA98026Plans will be delivered to:Name:James Wood:James.woodjr@cbre.comLocal Permit
#: :206.730.2965
Key Contacts:
Company
Name
Phone
Email
DOH Reviewer
KevinA Scarlett RA HFDP
360.236.2949
kevin.scarlett@doh.wa.gov
Facility Contact:
Swedish Edmonds
James Wood
206.730.2965
James.woodjr@cbre.com
Facility Admin.:
Swedish Edmonds
Mike Denney
206.215.2691
Mike.Denney@swedish.org
Arch./Eng.:
Other:
Swedish Edmonds
Sean Reardon
360.990.6995
sean.reardon@swedish.org
Other:
Swedish Edmonds
Rachel Jenner
rachel.jenner@swedish.org
Other:
Other:
Local AHJ:
City of Edmonds
Leif Bjorback
425.771.0220 xt1380
leif.bjorback@edmondswa.gov
Addt’l Copies To: L&I Electrical Section L&I Factory Assembled Structures Local Electrical AHJ
Project Status:
-Authorized to Begin Construction-
Comments are NOT APPROVED
The Construction Documents have been reviewed and found acceptable. All plan review comments have not been approved. Construction can begin, subject to construction permitting from
the local building official. See page two for important next steps.
To avoid delays it is important you follow these Next Steps:
Respond to Comments:
Revise project documents to be compliant with applicable rules and the review comments attached to this form.
Respond, in writing, to the comments attached to this form.
Submit revised plans and responses to comments to the Construction Review Services.
During Construction
Maintain a copy of the A2BC drawing set on the project site.
Submit any changes to the A2BC set to CRS for review and approval prior to executing the work.
If you have any questions please contact Construction Review Services (360) 236-2944. You can monitor project status and history at www.doh.wa.gov/crs.
Project Details (for internal use only)
Occupancy Type
IBC: IBC: IBC:
NFPA 101:
Construction Type
IBC: IBC: IBC:
NFPA 101: NFPA 101:
Fed Code:
Building Code:
Licensing Code:
Number of Beds Added: 0 Removed: 0
CON Required? Yes No
CON Approved Yes No
Req’d
Provided
Type/category
Are Hospital inpatients seen at this location? Yes No
Automatic Fire Sprinkler System:
Are planned residents/patients incapable of self preservation? Yes No
If yes, how many?
Automatic Fire Alarm System:
Emergency Power System:
Is sedation provided? Yes No
If yes, max. planned level?
Medical Gas System:
Smoke Compartmentation:
Is space Medicare certified?
Yes NoBuilding Department contacted? Estimated construction completion:
REVIEW NOTES
This project provides a new Medivator on the 6th floor with a temprary use location on the 1st floor during the 6th floor installation.Remove 6th floor medivator and temporarily install
in CCSD while we remodel room on 6h floor toaccommodate a new second medivator. Then the existing unit will be put back on the 6th floor. -kas
DSHS
For Assisted Living Facilities Only
Total Sleeping rooms
Minimum required area of day rooms/areas
Total Approved beds
Total area provided in day rooms/areas
Total Contract beds
NOTES TO SURVEY
Plan Review Comments:
Comment ID#
Approved
Not Approved
Comments Legend
O = Omitted comment
= current status of the comment – Approved / Not Approved / Deemed
N = Note only – a suggestion or recommendation and is NOT a requirement
1
Provide a copy of your Local Permits (include a copy of each permit as applicable –Bldg/Mech/Plumb/Elec, etc) required for this project. Just provide a pdf copy of cover page of each
indicating Facility Name/Address/Project Work Name and Permit Number. You must obtain Local permits from the City prior to the start of any construction. Submit these permit copies
as-soon-as obtained, Permit Finals are separate, Permit Finals are part of the project closeout procedure. This comment should resolve very soon after the project work begins. WAC 246-320-505(2)(b)
2
Contact CRS Senior Plans Reviewer Kevin A. Scarlett (KAS) at 360.236.2949 to schedule Inspection efforts. Plan one Final Inspection (Final when project work is complete). Inspection
efforts will occur via MS Meetings Video medium, the Facility must contact KAS to set-up and coordinate with the applicable site personnel. NOTE: KAS must organize this video meeting.
This comment will remain ‘open’ until construction is complete. WAC 246-320-505(2)(d)(v)
3
Verify/indicate what electrical work is necessary on this project. WAC 246-320-505 (2)(b)(ii)
4
Verify as existing or provide as new on plans indicating the room where the Medivator occurs is provided with ventilation which is negative pressure with all air exhausted (NO RA). This
relates to both 1st & 6thfloors in the Final Condition. 2013 ASHRAE 170 Table 7.1
5
Revise plans on both 1st & 6thfloors to show SA & EA grilles with cfm values. WAC 246-320-505 (2)(b)(ii)
6
Verify as existing or provide as new on plans indicating the (both) domestic water lines provide a reduced pressure backflow assembly (RPBA) for the water service to the Medivator. An
RPBA must be installed at EACH/ALL (hard plumbed equipment) in the facility. This relates to both 1st & 6thfloors in the Final Condition. 2018 UPC 601
7
Verify that ALL (each piece of equipment with waste pipe/tube) indirect waste pipe/tube terminates a minimum of 1” above the flood rim of the waste receptor. ALL (each piece of equipment
with waste pipe/tube) indirect waste lines require a 1”minimum air gap between any waste line and the flood plane of the waste receptor for any piece of equipment with a waste line.
Note: condensate tie to drain tailpipe is prohibited for any waste (other than AC coils).This relates to both 1st & 6thfloors in the Final Condition. 2018 UPC 801
8
Re: Temporary Operational Status; provide RPBAs and indirect waste at the temporary location (similar to comments #6 & #7 above. Note: the RPBAs (in Temporary status only) are NOT required
to mount affixed to walls and may connect via Wirsbo PEX or other NSF listed/tagged tubing/hose. Indirect waste still needs the 1” air gap to flood rim of waste receptor. 2018 UPC 601
& 801
9
Authorization to Begin Construction (A2BC) Status is based on and subject to Plan Sheet mark-ups (refer to A2BC Plans).
Additional comments may arise upon CRS review of subsequent submittal materials.
IMPORTANT NOTE: (Below)
When submitting a response to this letter, include your written response(do NOT highlight text-colored text is fine) directly in the word.docx cell of the comment at the very bottom
of the cell (your response is then the last text within the comment cell). Finally, submit the letter (via upload) electronically. Note: even if not directly in this letter, response
items submitted but not directly referenced by comment # will not be reviewed.
Compliance with the comments above provided by the Department of Health, Construction Review Services, are necessary for this facility to meet the cited requirements of the applicable
licensing regulations found in the Washington State Administrative Code and associated references. These comments, authorization to begin construction or final project approval do not
relieve the facility from the responsibility to meet the requirements of any applicable federal, state or local regulations. In the event of conflicts between other jurisdictions and
these written comments, the most stringent shall apply. The building owner or operator is ultimately responsible for safety and insuring the building is in compliance with all applicable
laws.