APPROVED BLD 1031553_Manual3.7m x 4.3m (12.1'x 14.1') WOOD GAZEBO
with ALUMINUM ROOF
Installation and Operating Instructions — YM12941Z
REVIEWED
Revised 08-21-2020
VdKD1STPY.,
Yardistry — North America
Toll Free Customer Support:
1.888.509.4382
info@yardistrystructures.com
www.yardistrystructures.com
Regular Hours: Mon - Fri, 8:30 am - 5:00
pm EST (excl. holidays)
(For extended hours see our website)
English and French Spoken
RECEIVED
1 2021
EDMONDS
ENT SERVICES
,RTMENT
,&Important Safety Notice!
Yardistry components are intended for privacy, decorative and ornamental use only.
Product is NOT INTENDED for the following:
• A safety barrier to prevent unsupervised access to pools, hot tubs, spas or ponds.
• As load bearing support for a building, structure, heavy objects or swings.
• Used in structures that trap wind, rain or snow that would create extra load on the
product.
Accumulated snow must be removed from roof.
DO NOT climb or walk on roof for any reason.
Permanent structures may require a building permit. As the purchaser and or installer of this
product you are advised to consult local planning, zoning and building inspection departments for
guidance on applicable building codes and/or zoning requirements.
Wood is NOT flame retardant and will burn. Grills, fire pits and chimineas are a fire hazard if
placed too close to a Yardistry structure. Consult user's manual of the grill, fire pit or chiminea
for safe distances from combustible materials.
Wear gloves to avoid injury from possible sharp edges of individual elements before assembly.
During installation, follow all safety warnings provided with your tools and use OSHA
approved safety glasses. Some structures may require two or more people to install safely.
Check for underground utilities before digging or driving stakes into the ground!
During assembly it is important to closely follow the instructions. Complete the assembly
on a solid, level surface and follow the instructions to square up, level and anchor the structure.
This will reduce the gaps at wood connections during assembly.
General Information
General Information: Wood components are manufactured with Cedar (C. Lanceolata)
which is protected with factory applied water -based stain. Knots, small checks (cracks)
and weathering are naturally occurring and do not affect the strength of the product.
Annual application of a water -based water repellent sealant or stain is important and will
help reduce weathering and checks.
www.yardistrystructures.com
Questions?
Call toll free or write us at:
Regular Hours: Mon - Fri, 8:30 am - 5:00 pm EST
(excl. holidays)
1 (888) 509-4382 (For extended hours see our website)
support@yardistrystructures.com
English and French Spoken
Patents Pending
2 support@yardistrystructures.com
Limited Warranty
Yardistry warrants that this product is free from defect in materials and workmanship for a
period of one (1) year from the original date of purchase. In addition, for any product with
lumber, all lumber is warranted for five (5) years against rot and decay. This warranty applies
to the original owner and registrant and is non -transferable.
Regular maintenance is required to assure the integrity of your product and is a requirement of
the warranty. This warranty does not cover any inspection costs.
This Limited Warranty does not cover:
• Labour for replacement of any defective item(s);
• Incidental or consequential damages;
• Cosmetic defects which do not affect performance or integrity;
• Vandalism; improper use or installation; acts of nature, including but not limited to wind,
storms, hail, floods, excessive water exposure;
• Minor twisting, warping, checking or any other natural occurring properties of wood that do
not affect performance or integrity.
Yardistry products have been designed for safety and quality. Any modifications made to
the original product could damage the structural integrity of the product leading to failure
and possible injury. Yardistry cannot assume any responsibility for modified products.
Furthermore, modification voids any and all warranties.
This product is warranted for RESIDENTIAL USE ONLY. Yardistry disclaims all other
representations and warranties of any kind, express or implied.
This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state
or province to province. This warranty excludes all consequential damages, however, some states/provinces
do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply
to you.
3 support@yardistrystructures.com
Instructions for Proper Maintenance
Your Yardistry structure is designed and constructed of quality materials. As with all outdoor
products it will weather and wear. To maximize the enjoyment, safety and life of your structure
it is important that you, the owner, properly maintain it.
HARDWARE:
• Check metal parts for rust. If found, sand and repaint using a non -lead paint complying
with 16 CFR 1303.
• Inspect and tighten all hardware after completion of assembly; after first month of use; and
then annually. Do not over -tighten as to cause crushing and splintering of wood.
• Check for sharp edges or protruding screw threads, add washers if required.
WOOD PARTS:
• Applying a water repellent or stain (water -based) on a yearly basis is important
maintenance to maintain maximum life and performance of the product.
• Check all wood members for deterioration, structural damage and splintering. Sand down
splinters and replace deteriorated wood members. As with all wood, some checking and
small cracks in grain is normal
• Some gapping may occur at some wood connections.
Tools Required:
• Tape Measure
• Carpenters Level
• Standard or Cordless Drill
• Claw Hammer
• 7/16" & 9/16" Wrench
Assembly Guides
• 8' Step Ladder
• Safety Glasses
• Adult Helper
• Safety Gloves
• Hard Hat
• 6' Step Ladder x 2
• Square
• Rachet
• 7/16, 1/2 & 9/16 Socket
Symbols:
Throughout these instructions symbols are provided in the top, right-hand corner of the page.
Use Help, where this is shown, 2, 3 or 4 Use a measuring tape to assure proper
people are required to safely complete location
this step. To avoid injury or damage to the
assembly make sure to get some help.
ii Pre -drill a pilot hole before fastening
screw or lag to prevent splitting of wood.
8
If you dispose of your Yardistry structure: Please disassemble and dispose of your
unit so that it does not create any unreasonable hazards at the time it is discarded. Be
sure to follow your local waste ordinances.
4 support@yardistrystructures.com
Assembly Tips
Following are some helpful tips to make the assembly process smooth and efficient.
PRE -ASSEMBLIES:
(i.e. Post and Beam Assemblies, Roof Rafter Assembly, etc)
• Work on a raised, solid and flat surface such as, a table or saw horse.
• Keep all connections flush where shown in the instructions.
• When assembling the beams keep parts flat, straight and snug when
connecting.
METAL PARTS:
• Roofing material may have sharp edges, wear safety gloves.
• Remove all plastic covering, on both sides of the metal panels, directly
before installing each piece.
• Place roofing material on a non-abrasive surface before and after assembly
as it can bend, dent and scratch easily.
• The roofing screws can easily crush the roof panels and roof edges when
using a power drill. We recommend hand tightening the roofing screws so
they sit snug and tight to the roofing material.
5 support@yardistrystructures.com
Permanent Installation Examples
Note: It is critically important you start with square, solid and level footings, concrete
pad or deck to attach your Pergola Room.
We supply Post Mounts with this structure which gives you the flexibility to permanently install your structure
to a pre-existing or new wood or concrete surface.
• The hardware to attach the Post Mount to the structure is included.
• The hardware to mount the structure permanently will need to be purchased separately at your local
hardware store.
If you are mounting to concrete footers see below for the correct locations and placement. Please double
check for possibility of any underground utilities such as gas, telephone, cable or sprinkler lines.
Following are some examples of how to mount the structure to wood or concrete surfaces.
Refer to your local building and city codes, ordinances, neighbourhood covenants, or height restrictions
regarding this type of structure for guidance on acceptable installation requirements.
Concrete Footer
Post Mount : : Anchoring Hardware not included
RequiredTO
Depth
Post to Post
3.92 m
12' 10-3/8"
4.59 m
3.31 m /
2.96 m 15' 3/4"
10' 10-3/8" 9' 8-7/16" Post to Post
Post to Post Plinth to Plinth i
Plinth to Plinth
3.42 m
11' 2-7/16"
support@yardistrystructures.com
Permanent Installation Examples cont.
Concrete Patio [min. 3.63 m x 4.24 m (11'11" x 13'11")] with 15.24 cm (6") clearance on all sides
Anchoring Hardware not included
Wood Deck [min. 3.63 m x 4.24 m (11'11" x 13'11")] with 15.24 cm (6")clearance on all sides
Hardware not
nt
Anchoring Hardware (not included)
Post Mounts have a 1.27 cm (112') diameter hole
for anchoring hardware.
support@yardistrystructures.com
EE
Roof to Post Bracket
X) Beam Long End FSC (445)
(4X)
Tie FSC (461)
(2X)
Beam Short End FSC (449)�
(4X)
Strap Short - Large Roof FSC (430)
(2X)
Beam Short Left FSC (451)
(2X)
Beam Short Centre FSC (450
(2X)
Beam Short Right FSC (452)
(2X)
Fascia Left - Large Roof FSC (435)
(2X)
6x9 Post FSC (851
(4X)
Post Mount (6in Post)
(8X)
Dof to Beam E
(14X)
Gazebo ID Plaque
(1X)
/ Strap Brace FSC (433) J
(2X)
_Strap Left - Large Roof FSC (431)
(2X)
Strap Right - Large Roof FSC (432) _
(2X)
Rafter Corner Right FSC (439)
(4X)
Beam Long Centre FSC (446)
(2X)
Top FSC (434)
(2X)
Spacer Top FSC (463)
(1X)
Tie Wrap Brackeet
(4X)
Gusset Left FSC (331)
(4X)
Long Beam Insert
(2X)
Beam Long Right FSC (448)
(2X)
Beam Long Left FSC (447)
(2X)
_Strap Short FSC (337)
(2X)
Rafter FSC (440)
(6X)
Strap FSC (437)
(2X)
Fascia Right FSC (444)
(2X)
Rafter Short Right FSC (442)
(4X)
Rafter Short Left FSC (441)
(4X)
Fascia Left FSC (443)
(2X)
Rafter Corner Left FSC (438)
(4X)
Fascia Right - Large Roof FSC (436)
(2X)
Plinth FSC (459)
(8X)
Plinth LongFSC (460)
(8X)
( Dimensions are approximate and are shown to assist in the identification of parts for
Part Identification
assembly. Actual dimensions may be smaller or larger.
152.4 x 228.6 x 2387.6mm (6 x 9 x 94")
4pc. (851) - 6x9 Post FSC
Y70229-851 o
o
(1-1/2 x 7-1/2 x 39-1/2") (1-1/2 x 7-1/2 x 39-1/2")
38.1 x 190.5 x 1003.3mm 38.1 x 190.5 x 1003.3mm
4pc. (330) - Gusset Right FSC 4pc. (331) - Gusset Left FSC
o Y70229-330 ° ° Y70229-331 °
o
38.1 x 139.7 x 2074.4mm (1-1/2 x 5-1/2 x 81-43/64")
pc. (447) - Beam Long Left FSC
0i 0 0
Y50229-447
38.1 x 139.7 x 2074.4mm (1-1/2 x 5-1/2 x 81-43/64")
pc. (448) - Beam Long Right FSC
FY0 0 °
50229-448
O O 0 0 0 00
38.1 x 139.7 x 2587.5mm (1-1 /2 x 5-1/2 x 101-7/8")
23.8 x 133.4 x 276.2mm
(5/4 x 6 x 10-7/8")
8pc. (460) - Plinth Long FSC
Y50229-460
23.8 x 133.4 x 200mm
(5/4 x 6 x 7-7/8")
8pc. (459) - Plinth FSC
Y50229-459
38.1 x 139.7 x 558.6mm
(1-1 /2 x 5-1/2 x 21-63/64")
4pc. (449) - Beam Short End FSC
Y50229-449 °
0 O
pc. (446) - Beam Long Centre FSC
T*-,
0 0 O
Y50229-446 o o o 0 0 0
38.1 x 139.7 x 1769.7mm (1-1/2 x 5-1/2 x 69-43/64")
pc. (451) - Beam Short Left FSC
Y50229-451 °
38.1 x 139.7 x 1769.7mm (1-1/2 x 5-1/2 x 69-43/64")
2pc. (452) - Beam Short Right FSC
Y50229-452
38.1 x 139.7 x 2422.1 m m (1-1 /2 x 5-1/2 x 95-23/64")
38.1 x 139.7 x 780.6mm
(1-1/2 x 5-1/2 x 30-47/64")
4pc. (445) - Beam Long End FSC
Y50229-445 i °
o i o
31.81/4 x 3 11/16 x9mm
' (1-1/4 x 3-11/16 x 22-3/4")
0 2pc. (434) - Top FSC
Y50229-434
pc. (450) - Beam Short Centre FSC
o o
i Y50229-450 i
o 0 o o o p
38.1 x 82.6 x 1853mm (1-1/2 x 3-1/4 x 72-61/64")
2pc. (443) - Fascia Left FSC
38.1 x 82.6 x 1853mm
o Y50229-443
(1-1/2 x 3-1/4 x 72-61/64")
2pc. (444) - Fascia Right FSC
38.1 x 82.6 x 2157.7mm
Y50229-444
(1-1/2 x 3-1/4 x 84-61/64")
2pc. (435) - Fascia Left - Large Roof FSC
°iY50229 435;
38.1 x 82.6 x 2157.7mm
(1-1/2 x 3-1/4 x 84-61/64")
31.8 x 76.2 x 1040.2mm
2pc. 436 - Fascia Right - Large Roof FSC
(1-1 /4 x 3 x 40-61 /64")
' Y50229-436
°
4pc. (441) - Rafter Short Left FSC '
Y50229-441
31.8 x 76.2 x 1915.4mm (1-1/4 x 3 x 75-13/32")
6pc. (440) - Rafter FSC
31.8 x 76.2 x 1040.2mm
Y50229-440
(1-1/4 x 3 x 40-61/64")
4pc. (442) - Rafter Short Right FSC
25.4 x 88.9 x 2601.9mm (1 x 3-1/2 x 102-7/16")
. �,Y50229-442
4pc. (439) - Rafter Corner Right FSC
25.4 x 88.9 x 2601.9mm
(1 x 3-1/2 x 102-7/16")
4pc. (438) - Rafter Corner Left FSC
70229-438, ,
m
31.8 x 81.6 x 574.7mm
(1-1/4 x 3-7/32 x 22-5/8")
1 pc. (463) - Spacer Top FSC
Y50229-463 •
10 support@yardistrystructures.com
Part IdP-ntifir-Minn ( Dimensions are approximate and are shown to assist in the identification of parts for
u13JQl l luly. nl- uul u111 IQI IJlul IJ 11 luy uQ 311 lu QI ul
31.8 x 82.6 x 1561.3mm (1-1A x 3-1/4 x 61-15/32")
2pc. (337) - Strap Short FSC
Y50229-337
31.8 x 82.6 x 2170.9mm (1-114 x 3-1/4 x 85-15/32")
2pc. (430) - Strap Short - Large Roof FSC
31.8 x 82.6 x 2603.5mm
(1-1 /4 x 3-1/4 x 102-1 /2")
2pc. (437) - Strap FSC
Y50229-437
31.8 x 82.6 x 1605.6mm (1-1/4 x 3-1/4 x 63-13/64")
2pc. (432) - Strap Right - Large Roof FSC
Y50229-432
31.8 x 82.6 x 1605.6mm (1-1A x 3-1/4 x 63-13/64")
2pc. (431) - Strap Left - Large Roof FSC
Y50229-431
31.8 x 88.9 x 2336.8mm (1-1A x 31/2 x 92")
2pc. (461) - Tie FSC
31.8 x 82.6 x 574.7mm (1-1A x 3-1/4 x 22-5/8")
2pc. (433) - Strap Brace FSC
Y50229-433
NOTE: Parts have been packed inside (851) 6 x 9 Post.
Check for parts inside the posts.
11 support@yardistrystructures.com
Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of 1
parts for assembly. Actual dimensions maybe smaller or larger. J
4pc. - Short Panel Left
4pc. - Long Panel Left
(Y01030-127)
2pc. - Middle Panel
(Y01030-130)
4pc. - Long Panel Right
(Y01030-129)
4pc. - Short Panel Right
(Y01030-128)
4pc.
Ridge Cap Short 25.2
(Y01030-132)
1 pc. - Roof Panel Set
(Y70830-138)
4pc. Roof Edge Left 72.2 - (Y01030-134)
2pc. Roof Edge Right 72.2 - (Y01030-135)
2pc. Roof Edge Right 96.2 - (Y01030-136)
813c. Ridge Clip 102.5 - (Y01030-133)
4pc.
0 0 0 °
Ridge Cap Long 81.5
2pc. Long Beam Insert - (Y00429-124) ° ° ° J. (Y01030-131)
1 pc.
Tie Wrap Bracket (4Pk) 2pc'
Peak Post
(Y70829-106)
. o•
1 pc.
Peak Cap Long 2pc.
(Y01030-137) ® Contoured Washer
2pc (Y05918-211)
Carriage Bolt 4pc.
1 pc. - Corner Cap Set (4Pk) (Y07428-260) NRracket
(Y70830-103) 125)
1 pc. Weather Seal
Ridge Clip (8PK) (b Y70818-0741 pc. -Roof To Beam 2pc.
Bracket Set (14Pk) Spring Clip
1pc.-GazeboID laque (Y70829-123) (Y09490-001)(Y70800-104)1/4Nut 2pc.
o (Y08490-200) Peak Loop
0 2pc. - 50mm (Y20018-003)
1 pc. - Post Hook 1 pc. - Roof To Post 1 pc.
Mount Set (8Pk) Bracket Set (4Pk) 1/4" Eye Lag 1pc. - Roof Peak Set
(Y70829-122) (Y00418-050) (Y70829-070) (Y00218-001) (Y70829-125)
12 support@yardistrystructures.com
Hardware Identification ( Dimensions are approximate and are shown to assist in the identification of
parts for assembly. Actual dimensions may be smaller or larger.
.12pc.:•(Y07718-223)
�I IIIIIIIIIII011111111111111111'
12pc. Hex Bolt 5/16 x 3" - (Y07718-330)
Jim
r� 16pc. Hex Bolt 5/16 x 3-3/4" - (Y07718-333)
16pc. Lag Screw 5/16 x 3" - (Y06218-330)
16pc Hex Bolt 5/16 x 1-1/4"
(Y07718-31 1)
pc. Pan Screw #10 x 1-1/4" 4pc. Pan Screw #10 x 2-1/2" - (Y06491-722)
T wuumxr- 60
(Y06491-711)
24pc. Pan Screw #8 x 1"
42pc. Pan Screw #12 x 1-1/2" (Y06491-510)
(Y06491-612)
ii;
79pc. Wood Screw #8 x 2 1 /4" - (Y06091-521) 168pc. Wood Screw #8 x 1-1 /2"
(Y06091-512)
11pc, Wood Screw • i �1.1 • I Wood Screw,����1/��i��/�Ij!/%r�1 • 1 1 1 I 1�1��1pQ�Q�1p1p1��Q$1p1pQ�1��Q�Q�Q�1��1�r►
16pc.
3/8 x 1-1/4" Large Washer
(Y05118-811)
1/4-5/16 x 1-1/4'' Large Washer
(Y05118-311)
12pc. - 1/4" Lock Nut
(Y08318-203)
q7�
8pc. - 3/8" Lock Nut
(Y08318-803)
Sri
68pc. 5/16" Lock Washer
(Y05318-300)
LD:=
1 pc. - Hex Driver
(Y00400-004)
1 pc. #2 x 2" Robertson Driver (Y00400-005)
236pc. Hex Roofing Screw
1� �,�Q�Q�Q�Q�Q�Q�Q�Q�11r► #8
1
d624pc. Sheet Metal Screw
#8 x 3/4"
(Y06430-503)
Z-
68pc. 5/16 - T-Nut
(Y08518-300)
4pc. Hex Bolt
3/8 x 9-1/2"
(Y07718-892)
4pc. Hex Bolt
3/8 x 12-1/2"
'Y07718-822)
13 support@yardistrystructures.com
STOP STOP STOP STOP
• Each step indicates which bolts and/or screws you will need for assembly, as well as
1-888-509-4382
support@yardistrystructures.com
C. Read the assembly manual completely, paying special attention to ANSI warnings;
notes; and safety/maintenance information on pages 1 - 4.
• Follow the instructions in order.
• This structure is designed to be assembled and installed ideally by four people,
DO NOT attempt to install alone.
• Consider the slope of elevation where you plan to install the structure. Also, check for
gas, telephone, other utilities or sprinkler line locations prior to excavating any holes.
D. Before you discard your cartons fill out the form below.
• The carton I.D. stamp is located on the end of each carton.
• Please retain this information for future reference. You will need this information if you
contact the Consumer Relations Department.
PRODUCT NUMBER: YM12941Z
CARTON I.D. STAMP: _ _ _ _ _ (Box 1)
CARTON I.D. STAMP: _ _ _ _ _ (Box 2)
CARTON I.D. STAMP: _ _ _ _ _ (Box 3)
14 support@yardistrystructures.com
Step 2: Post Assemblies
A: At the bottom of one (851) 6 x 9 Post insert two 5/16" T-Nuts on the outside of each long side. (fig. 2.2)
B: At the bottom of the same (851) 6 x 9 Post place two Post Mounts tight to the bottom and inside faces on the
long sides as shown in fig. 2.1 and 2.2. Loosely attach with two 5/16 x 1-1/4" Hex Bolt (with 5/16" lock washer
and 1/4-5/16" large washer) per mount so they connect to the T-Nuts. From the bottom attach with two #8 x 1-1/2"
Wood Screws and two #10 x 1-1/4" Pan Screws per mount. Tighten bolts.
C: Flush to the bottom of (851) 6 x 9 Post place one (460) Plinth Long on each long side and one (459) Plinth on
each short side and attach with four#8 x 1-1/2" Wood Screws per plinth. Rounded edges on top. (fig. 2.1, 2.2
and 2.3)
D: Repeat Steps A - C three more times to make four Post Assemblies.
Top (851) 6 x 9 Post
Fig. 2.2
#8 x 1-1/2"
Wood Screws o Long
(x 4 per Plinth) /Side
(460) 1
Plinth Short
Long Side
Post Mount
(459)
Plinth
O
Q)
Bottom
S MOW-0 5/16 x 1-1/4" Hex Bolt
® (x2 per Post Mount,
i from inside)
9
5/16" Lock
Washer
-0
To
1/4 - 5/16"
Large Washer
Plinth vr LI
#8 x 1-1/2" Wood Screws
#10 x 1-1/4" (x 2 per Post Mount, from
Pan Screws outside)
(x 2 per Post 5/16" T-Nut (x 4 Post
Mount, from per Post) Mount
inside)
(460)
Plinth
Long
Wood Parts
4 x (851) 6 x 9 Post
8 x (459) Plinth
8 x (460) Plinth Long
Fig. 2.1
Rounded
Fiq. 2.3 Edge on Top
Hardware
80 x #8 x 1-1/2" Wood Screw 16 x 5/16" T-Nut
16 x #10 x 1-1/4" Pan Screw 16 x 5/16 x 1-1/4" Hex Bolt
8 x Post Mount (with 5/16" lock washer, 1/4 - 5/16" large washer)
15 support@yardistrystructures.com
Step 3: Short Beam Assembly
Part 1
A: Connect one (451) Beam Short Left and one (452) Beam Short Right using two 5/16 x 1-1/2" Hex Bolts (with
5/16" lock washer, 1/4-5/16" large washer and 5/16" t-nut) as shown in fig. 3.1 and 3.2.
B: Connect one (449) Beam Short End to each end of one (450) Beam Short Centre using two 5/16 x 1-1/2" Hex
Bolts (with 5/16" lock washer, 1/4-5/16" large washer and 5/16" t-nut) per end as shown in fig. 3.1 and 3.2.
C: Repeat Steps A and B one more time to make two Short Beam L-R Assemblies and two Short Beam End
Assemblies.
9
(452) Beam
Short Right
q
Fig. 3.1
(449) Beam
Short End
. 4
0
0
(451) Beam
Short Left
(450) Beam
Short Centre
Tight
Fig. 3.2 m
q �
4
' 6
6' 0
q .
O l�
�P 5/16" (449) Beam
T-nut Short End
5/16 x 1-1/2"
Hex Bolt
Make sure bolt heads
are on the outside of
1/4-5/16" each Beam Assembly
5/16" Lock Large Washer
Washer
Wood Parts Hardware
4 x (449) Beam Short End 12 x 5/16 x 1-1/2" Hex Bolt
2 x (450) Beam Short Centre (5/16" lock washer, 1/4-5116" large washer, 5/16" t-nut)
2 x (451) Beam Short Left
2 x (452) Beam Short Right
16 support@yardistrystructures.com
Step 3: Short Beam Assembly
Part 2
D: Place one Short Beam L-R Assembly tight to one Short Beam End Assembly so the ends are flush. Match
the bolt holes in each (449) Beam Short End with the bolt holes in (451) Beam Short Left and (452) Beam Short
Right. Attach with 18 #8 x 2-1/2" Wood Screws. (fig. 3.3 and 3.4)
E: Repeat Step D one more time to make two Short Beam Assemblies.
Flush
Hint
both
bolt i
bolt.
#8 x 2-1/�
Screws (x
assembly
End Assembly
Hardware
36 x #8 x 2-1/2" Wood Screw
17 support@yardistrystructures.com
Step 4: Long Beam Assembly
Part 1
A: Connect one (447) Beam Long Left and one (448) Beam Long Right using two 5/16 x 1-1/2" Hex Bolts (with
5/16" lock washer, 1/4-5/16" large washer and 5/16" t-nut) as shown in fig. 4.1 and 4.2.
B: Connect one (445) Beam Long End to each end of one (446) Beam Long Centre using one 5/16 x 1-1/2" Hex
Bolts (with 5/16" lock washer, 1/4-5/16" large washer and 5/16" t-nut) in the top holes per end as shown in fig. 4.1
and 4.2.
C: Repeat Steps A and B one more time to make two Long Beam L-R Assemblies and two Long Beam End
Assemblies.
(448) Beam
` Long Right
` Fig. 4.1
e�
(445) Beam
Long End
5/16 x 1-1/2"
Hex Bolt
e
(446) Beam
Long Centre +
(447) Beam
Long Left
Use top +
holes
5/16" T-nut
5/16" Lock
Washer
Tight `
�t
5/16 x 1-1/2"
Hex Bolt �>
See Part 2
q for this piece
4
Fig. 4.2
(445) Beam
Long End
1/4-5/16" Make sure bolt heads
Large Washer are on the outside of
each Beam Assembly
Wood Parts Hardware
4 x (445) Beam Long End 8 x 5/16 x 1-1/2" Hex Bolt
2 x (446) Beam Long Centre (5/16" lock washer, 1/4-5/16" large washer, 5/16" t-nut)
2 x (447) Beam Long Left
2 x (448) Beam Long Right
18 support@yardistrystructures.com
Step 4: Long Beam Assembly
Part 2
D: Place one Long Beam Insert in between one Long Beam L-R Assembly and one Long Beam End Assembly
then fit tight together so the beam assembly ends are flush. Match the bolt holes and wood screw pilot holes in
both beam assemblies and Long Beam Insert. (fig. 4.3, 4.4 and 4.5)
E: Attach beam assemblies and Long Beam Insert together with six 5/16 x 3" Hex Bolts (with 5/16" lock washer,
1/4-5/16" large washer and 5/16" t-nut) and 14 #8 x 2-1/2" Wood Screws. (fig. 4.5 and 4.6)
F: Repeat Step D-E make a second Long Beam Assembly.
Long Beam L-R
Assembly
Long Beam L-R
Assembly Long Beam n
Insert
Fig. 4.3 Fig. 4.4
A Long Beam This bolt wasO
Insert previously installed
n Step 4, Part 1B ,� Align holes in all
$ 3 pieces with 5116
x 2-314" hex bolts
o y'
Flush
Long Beam
Long Beam \ End Assembly
End Assembly
Fig. 4.5
5/16" Lock 5/16 x 3"
1/4-5/16" Washer Hex Bolt x 6
Large Washer
Long Beam L-R
Assembly
* ° Fig. 4.6
o �
,p Long Beam
Insert 5/16" D
T-nut `
Long Beam V
End Assembly
�9
4
Notice the side the bolts
and screws are installed in
fig. 4.3, 4.5 and 4.6. Bolts #8 x 2-1/2" Wood Screws
are on the opposite side of * (x 14 per assembly)
the screws f
Comoonets:
2 x Long Beam Insert
sh
Hardware
28 x #8 x 2-1/2" Wood Screw
12 x 5/16 x 3" Hex Bolt
(5/16" lock washer, 1/4-5/16" large washer, 5/16" t-nut)
19 support@yardistrystructures.com
Step 5: Frame Assembly and Anchoring
Part 1
A: Move your Post Assemblies to the final location.
Make sure the ground is flat and level before
continuing assembly.
B: With one person at each Post stand two
complete Post Assemblies. A third person places
one Long Beam Assembly against the outside of
two Posts, flush to the tops and outside corners.
Notice bolt hole orientation on the Long Beam
Assembly and the long side of the Post Assembly
is along the Long Beam Assembly. A fourth person
attaches Beam to Post with one 3/8 x 9-1/2" Hex
Bolt (with two 3/8" large washers and one 3/8" lock
nut) per Post. The distance from the outside of one
Post to the outside of the second Post should be
12' 10-3/8". (fig. 5.1, 5.2 and 5.3)
C: Place one Short Beam Assembly against the
outside of two Posts, flush to the tops and outside
corners and tight to Long Beam Assembly. Notice
bolt hole orientation on the Short Beam Assembly
and the short side of the Post Assembly is along
the Short Beam Assembly. Attach Beam to Post
with one 3/8 x 12-1/2" Hex Bolt (with two 3/8" large
washers and one 3/8" lock nut) per Post. The
distance from the outside of one Post to the outside
of the second Post should be 10' 10-3/8". Continue
until all four Beam Assemblies are attached and the
corners are tight together. (fig. 5.1 and 5.2) See
fig. 5.3 for accurate positioning of Posts.
Fig. 5.3
10' 10-3/8"
Post to Post
12' 10-3/8"
Post to Post
15' 3/4"
Post to Post
11' 2-7/16"
Plinth to Plinth
9' 8-7/16"
Plinth to Plinth
S
A
Note hole
orientation (on Fig. 5.2
bottom)
Note hole
orientation (on
3/8" Lock 3/8" Large bottom)
e Nut Washer
3/8" Lock
Nut
Long Beam
Assembly
3/8 x 9-1/2" /J
Hex Bolt
3/8" Large
Washer
Long Side
Post Assembly
Hardware
Short Beam
Assembly
3/8" Large
Washer
3/8 x 12-1/2"
Hex Bolt
4 x 3/8 x 9-1/2" Hex Bolt (3/8" large washer x 2, 3/8" lock nut)
4 x 3/8 x 12-1/2" Hex Bolt (3/8" large washer x 2, 3/8" lock nut)
20 support@yardistrystructures.com
Step 5: Frame Assembly and Anchoring I
F'1� �,"' fi fi fi fi O�
Part 2 � II II II
D: Make sure each corner is square and level then attach Beam Assemblies to Post Assemblies with two 5/16
x 4-3/4" Lag Screws (with 1/4-5/16" large washer) per corner. (fig. 5.4)
E: Depending on what you are placing the Gazebo on will determine how you anchor it to that surface. Please
refer to pages 6 and 7 for installation examples.
Any hardware or extra materials for
mounting will have to be purchased in advance.
Fig. 5.4
Long Beam
Assembly
1/4-5/16"
Large Washer
5/16 x 4-3/4"
Lag Screw
Post Assembly
Short Beam
Assembly
1/4-5/16"
Large Washer
5/16 x 4-3/4"
Lag Screw
Hardware
8 x 5/16 x 4-3/4" Lag Screw (1/4-5/16" large washer)
21 support@yardistrystructures.com
Step 6: Attach Gussets and Roof Brackets Lk
Note: The bevelled ends on each gusset should always face away from the wood it is attaching to.
A: Make sure the assembly is still square and level then facing one Long or Short Beam Assembly place one
(330) Gusset Right on the right hand side so the top fits tight to the Beam Assembly and the bottom fits tight to the
Post Assembly. Attach gusset to Beam Assembly with two 5/16 x 3-3/4" Hex Bolts (with 5/16" lock washer, 1/4-
5/16" large washer and 5/16" t-nut). Pre -drill with a 1/8" drill bit then attach gusset to Post Assembly with two 5/16
x 3" Lag Screws (with 1 /4-5/16" large washer). (fig. 6.1, 6.2 and 6.3)
B: Repeat Step A on the left hand side with one (331) Gusset Left. (fig. 6.1, 6.2 and 6.3)
C: Repeat Steps A and B for each Beam Assembly/Post Assembly. (fig. 6.1, 6.2 and 6.3)
D: At each corner, tight to the outside edges of the joining Beam Assemblies attach one Roof to Post Bracket with
two #10 x 1-1/4" Pan Screws. (fig. 6.3 and 6.4)
Fig. 6.1 (331) Gusset
Left \
(331) Gusset
Short Beam
Assembly
Long Beam 5/16" Lock
Fig. 6.3 Assembly Washer
5/16" �
��
A T-nut
A �
5/16 x 3-3/4"
1/4-5/16" Hex Bolt
Large Washer
Gusset
Left
Fig. 6.2 Short Beam
Long Beam Assembly
Assembly \
V '
5/16 x 3-3/4"
Hex Bolt
(330) Gusset
Right
#10 x 1-1/4"
Pan
(331) Gusset
Left
. r
,i �5/16 x 3"
Lag Screw
Post 1/4-5/16"
Assembly Large Washer
b.4
Roof to Post
Bracket
(330) Gusset \
Right • Short Beam
Assembly
5/16 x 3" Post Long Beam
Lag Screw Assembly Assembly
1/4-5/16"
Large Washer
Wood Parts Hardware
4 x (330) Gusset Right 16 x 5/16 x 3" Lag Screw (1/4-5116" large washer)
4 x (331) Gusset Left 16 x 5/16 x 3-3/4" Hex Bolt
(5/16" lock washer, 1/4-5/16" large washer, 5/16" t-nut)
8 x #10 x 1-1/4" Pan Screw
4 x Roof to Post Bracket
22 support@yardistrystructures.com
Step 7: Fascia Beam Assemblies
A: Tightly connect one (443) Fascia Left and one (444) Fascia Right using one 5/16 x 1-1/2" Hex Bolt (with 5/16"
lock washer, 1/4-5/16" large washer and 5/16" t-nut) as shown in fig. 7.1 and 7.2. Repeat to make a second Fas-
cia Beam Assembly.
B: Tightly connect one (435) Fascia Left - Large Roof and one (436) Fascia Right - Large Roof using one 5/16
x 1-1/2" Hex Bolt (with 5/16" lock washer, 1/4-5/16" large washer and 5/16" t-nut) as shown in fig. 7.3 and 7.4.
Repeat to make a second Large Fascia Beam Assembly.
Fig. 7.2 Tight
(443) Fascia 5/16"
Fig. 7.1 Left �T-nut
0
0
1/4-5/16"
5/16 x 1-1/2", Large Washer
q Hex Bolt
5/16" Lock
(435) Fascia Left Washer
- Large Roof
Fig. 7.3 (444) Fascia
Right
Tight
Fig. 7.4 (436) Fascia Right
- Large Roof
0 5/16"
T-nut
5/16 x 1-1/2" 5/16" Lock 1/4-5/16"
Hex Bolt Washer Large Washer
Wood Parts Hardware
2 x (443) Fascia Left 4 x 5/16 x 1-1/2" Hex Bolt
2 x (444) Fascia Right (5/16" lock washer, 1/4-5116" large washer, 5/16" t-nut)
2 x (435) Fascia Left - Large Roof
2 x (436) Fascia Right - Large Roof
23 support@yardistrystructures.com
Step 8: Small Roof Rafter Assembly
Part 1
A: On each side of one (440) Rafter place one (438) Rafter Corner Left and one (439) Rafter Corner Right so
the tops and edges are flush then attach with two #8 x 2-1/4" Wood Screws per side. (Fig. 8.1 and 8.2)
B: Place Fascia Beam Assembly from Step 7A on the bottom of (438) Rafter Corner Left, (439) Rafter Corner
Right and (440) Rafter so the sides are flush then attach with two #8 x 2-1/4" Wood Screws at each end and two
in the middle. (fig. 8.1, 8.3 and 8.4)
C: Repeat Steps A and B to make a second Small Roof Rafter Assembly.
#8 x 2-1/4" Flush
Wood Screws
Fig. 8.2
(438) Rafter
Corner Left
(440).
Rafter
Fascia Beam
Assembly
Fig. 8.3
ti
#8 x 2-1/4"
Wood Screws
(439) Rafter
Corner Right
Note notches
facing up
(438) Rafter
Corner Left
(440)
Rafter
Flush
#8 x 2-1/4"
Wood Screws °
(x per
Fascia Beam
Assembly)
(440)
Rafter
Fascia Beam
Assembly
Fig. 8.1
(439) Rafter
Corner Right
(439) Rafter
Corner Right
Flush k
Fig. 8.4
6
6
O
#8 x 2-1/4"
Wood Screws
Fascia Beam
Note angle Assembly
side up
Wood Parts Hardware
2 x (440) Rafter 20 x #8 x 2-1/4" Wood Screw
2 x (438) Rafter Corner Left
2 x (439) Rafter Corner Right
24 support@yardistrystructures.com
Step 8: Small Roof Rafter Assembly
Part 2
D: Place one (337) Strap Short in the notches of (438) Rafter Corner Left, (439) Rafter Corner Right and (440)
Rafter so the ends do not overhang the outside edges of the outside boards then attach with six #8 x 1-1/2"
Wood Screws. (Fig. 8.5)
E: Place one (437) Strap in the notches of (438) Rafter Corner Left, (439) Rafter Corner Right and (440) Rafter
so the ends do not overhang the outside edges of the outside boards. Do not attach yet. (fig. 8.5)
F: Place one (442) Rafter Short Right and one (441) Rafter Short Left in the notches of (437) Strap and attach
as shown in fig. 8.5 with four #8 x 1-1/2" Wood Screws and two #8 x 2-1/4" Wood Screws per board.
G: Attach (437) Strap to (438) Rafter Corner Left, (439) Rafter Corner Right and (440) Rafter with six #8 x
1-1/2" Wood Screws. (fig. 8.5)
H: Complete Steps D, E, F and G for both Small Roof Rafter Assemblies.
(440)
(337) Strap Rafter
Short
Fig. 8.5
(438) Rafter
#8 x 1-1/2" Wood Screws Corner Left
(439) Rafter
x 20 per assembly t , Corner Right
Flush
o -
No
Overhang
Fascia Beam
Assembly �
#8 x 2-1/4"�
Wood Screws
(441) Rafter
Short Left
(437) Strap
#8 x 2-1/4 (442) Rafter
Wood Screws Short Right
Flush
Wood Parts
2 x (337) Strap Short
2 x (437) Strap
2 x (442) Rafter Short Right
2 x (441) Rafter Short Left
Hardware
40 x #8 x 1-1/2" Wood Screw
8 x #8 x 2-1/4" Wood Screw
25 support@yardistrystructures.com
Step 9: Attach Roof to Beam Brackets
-Small Roof Rafter Assembly
A: On the Back of one Small Roof Rafter Assembly, centred and flush to the bottom of (442) Rafter Short Right,
(441) Rafter Short Left and (440) Rafter attach one Roof to Beam Bracket per board with one #8 x 1 " Pan Screw
in the bottom hole and one #12 x 1-1/2" Pan Screw in the top hole per bracket. Make sure to only install on one
Small Roof Rafter Assembly, the second will not have brackets. (fig. 9.1 and 9.2)
Fig. 9.1
Back View (442) Rafter
Sho Right
a
(440)
Rafter
Fascia Beam
Assembly
(441) Rafter
Short Left Roof to Beam
Bracket
Fig. 9.2
a
Fascia Beam
Assembly
Centred and flush to
bottom of rafters #12 x 1-1/2"
Pan Screw
#8 x 1" Pan
Screw
Hardware
3 x #8 x 1" Pan Screw
3 x #12 x 1-1/2" Pan Screw
3 x Roof to Beam Bracket
26 support@yardistrystructures.com
Step 10: Large Roof Rafter Assembly
Part 1
A: On each side of one (434) Top place one (440) Rafter so the tops and edges are flush then attach with two
#8 x 2-1/2" Wood Screws per side. (Fig. 10.1 and 10.2)
B: Place Large Fascia Beam Assembly from Step 7B on the bottom of (440) Rafters so the sides are flush and
holes are centred on the (440) Rafters then attach with two #8 x 2-1/4" Wood Screws per (440) Rafter. (fig. 10.1
and 10.3)
C: Repeat Steps A and B to make a second Large Roof Rafter Assembly.
Flush
Wood Parts
4 x (440) Rafter
2 x (434) Top
. 10.1
angle
�e up
Hardware
8 x #8 x 2-1/4" Wood Screw
8 x #8 x 2-1/2" Wood Screw
27 support@yardistrystructures.com
Step 10: Large Roof Rafter Assembly
Part 2
D: Beside each (440) Rafter place one (438) Rafter Corner Left and one (439) Rafter Corner Right so the tops
and edges are flush and the bottom edges are flush to Large Fascia Beam Assembly then attach with two #8 x
2-1/4" Wood Screws to the top and bottom of the rafters per side. (Fig. 10.4, 10.5 and 10.6)
E: Repeat Step D for the second Large Roof Rafter Assembly.
Fig. 10.5
r
t a
6
I
Flush
(438) Rafter
#8 x 2-1/4" Corner Left
Wood Screws
Fig. 10.4
(440)
Rafter
(439) Rafter
Corner Right
� Note notches
facing up
Large Fascia
Beam Assembly
Note notches
facing up
Flush
Rafter
Fig. 10.6 Corner
Left and
a Right
0
#8 x 2-1/4'� o
Wood Screws
Large Fascia
Beam Assembly
Wood Parts
2 x (438) Rafter Corner Left
2 x (439) Rafter Corner Right
Hardware
16 x #8 x 2-1/4" Wood Screw
28 support@yardistrystructures.com
Step 10: Large Roof Rafter Assembly
Part 3
F: Place one (430) Strap Short - Large Roof in the notches of (438) Rafter Corner Left, (439) Rafter Corner
Right and both (440) Rafters so the ends do not overhang the outside edges of the outside boards then attach
with eight #8 x 1-1/2" Wood Screws. (Fig. 10.7)
G: Place one (431) Strap Left - Large Roof in the notches of (438) Rafter Corner Left and one (440) Rafter and
one (432) Strap Right - Large Roof in the notches of (439) Rafter Corner Right and the other (440) Rafter so the
ends do not overhang the outside edges of the outside boards. Boards are tight in the centre. Do not attach
yet. (fig. 10.7)
H: Place one (442) Rafter Short Right in the notches of (432) Strap Right - Large Roof and one (441) Rafter
Short Left in the notches of (431) Strap Left - Large Roof and attach to (438) Rafter Corner Left and (439) Rafter
Corner Right with two #8 x 1-1/2" Wood Screws per board and to Large Fascia Beam Assembly with two #8 x
2-1 /4" Wood Screws per board.
I: Attach (431) Strap Left - Large Roof and (432) Strap Right - Large Roof to (438) Rafter Corner Left, (439)
Rafter Corner Right and (440) Rafter with six #8 x 1-1/2" Wood Screws per board. (fig. 10.7)
Fig. 10.7
(438) Rafter (440)
Corner eft Rafter
#8 x 1-1/2" Wood Screws
x 24 per assembly
11
(439) Rafter
Corner Right
(430) Strap
Short - Large
Roof
(441) Rafter
Short Left
#8 x 2-1/4"
Wood Screws No
(431) Strap Left Overhang
- Large Roof
Large Fascia (432) Strap Right
Beam Assembly - Large Roof
#8 x 2-1/4°�
Wood Screws
(442) Rafter
Short Right
2 x (430) Strap Short - Large Roof
2 x (431) Strap Left - Large Roof
2 x (432) Strap Right - Large Roof
2 x (442) Rafter Short Right
2 x (441) Rafter Short Left
Hardware
48 x #8 x 1-1/2" Wood Screw
8 x #8 x 2-1/4" Wood Screw
29 support@yardistrystructures.com
Step 10: Large Roof Rafter Assembly
Part 4
J: Turn Large Roof Rafter Assembly over then attach one (433) Strap Brace to (431) Strap Left - Large Roof
and (432) Strap Right - Large Roof with eight #8 x 2-1/4" Wood Screws. Edges are flush. (fig. 10.8 and 10.9)
K: Complete Steps F - J for both Large Roof Rafter Assemblies.
Fig. 10.8
Front View
440
Rafter
(431) Strap Left
- Large Roof
s
(432) Strap Right
- Large Roof
#8 x 2-1/4" Wood
Screws x 8
Fig. 10.9
Back View
(433) Strap
Brace
Flush
(432) Strap Right
- Large Roof (431) trap Left
- Large Roof
Wood Parts Hardware
2 x (433) Strap Brace 16 x #8 x 2-1/4" Wood Screw
30 support@yardistrystructures.com
Step 11: Attach Roof to Beam Brackets
- Large Roof Rafter Assemblies
A: On the Back of both Large Roof Rafter Assemblies, centred and flush to the bottom of (442) Rafter Short
Right, (441) Rafter Short Left and both (440) Rafter attach one Roof to Beam Bracket per board with one #8 x 1"
Pan Screw in the bottom hole and one #12 x 1-1/2" Pan Screw in the top hole per bracket. (fig. 11.1 and 11.2)
Fig. 11.1
Back View
(442) Rafter
Short Right
(440)
Rafter
Large Fascia
Beam Assembly
(441) Rafter
Short Left
Roof to Beam
Bracket
Fig. 11.2
d�
Large Fascia
Beam Assembly
Centred and flush to
bottom of rafters
#12 x 1-112"
Pan Screw
#8 x 1" Pan
Screw
Hardware
8 x #8 x 1"Pan Screw
8 x #12 x 1-1/2" Pan Screw
8 x Roof to Beam Bracket
31 support@yardistrystructures.com
STOP I I STOP I I STOP I I STOP
INSTALLING ROOFING MATERIAL
CAUTION!
Roofing material may have sharp edges! Wear gloves!
HANDLE WITH CARE!
Place roofing material on a non-abrasive surface before assembly as it
can bend, dent and scratch easily.
The roofing screws can easily crush the Roof Panels and Roof
Edges when using a power drill. We recommend hand tightening the
roofing screws so that they sit snug and tight to the roofing material.
32 support@yardistrystructures.com
Ail 0NI►1con IMMCs] 21L1Icon MF 12INri
•
BE SURE TO REMOVE ALL PLASTIC COVERING, ON
BOTH SIDES OF THE ALUMINUM PANELS AND TRIM,
DIRECTLY BEFORE INSTALLING EACH PIECE. (One side
is clear and the other is blue, both must be removed.)
Example #1
Example #3
Example #2
Step 12: Attach Roof Panels - Small Roof
Part 1
A: Place one Long Panel Left on the front of one Small Roof Rafter Assembly so it is flush to the side of (438)
Rafter Corner Left and a slight overhang at the bottom of the Fascia Beam Assembly. Holes should line up with
(440) Rafter. (fig. 12.1 and 12.2)
B: Place one Long Panel Right on Small Roof Rafter Assembly so it overlaps the Long Panel Left and it is flush
to the side of (439) Rafter Corner Right and a slight overhang at the bottom of the Fascia Beam Assembly. (fig.
12.1 and 12.2)
C: Attach both Left and Right Long Panels to Small Roof Rafter Assembly with four #8 x 1" Roofing Screws in
locations shown in fig. 12.1. Be sure not to overtighten screws.
D: Repeat Steps A - C for both Small Roof Rafter Assemblies.
Fig. 12.2
Top, Side View
DO NOT overtighten #8 x 1°
screws could cause Roofing
� Panels overlap Screws
damage to roofing at the seams
material a
Flush D (438) Rafter
Corner Left
V D
(439) Rafter
Corner Right
(440)
Rafter
#8x1"
Roofing
Fig. 12.1 Screws
Front View
Flush Lower 3 screws may have
(438) Rafter Flush / to be removed in next step
Corner Left ((/ to properly place Left and
Right Short Panels
(439) Rafter
Corner Right
Fascia Beam
Assembly
Long Panel
Left Long Panel
Right Slight overhang
Roof Parts
2 x Long Panel Left
2 x Long Panel Right
Hardware
8 x #8 x 1"Roofing Screw
34 support@yardistrystructures.com
Step 12: Attach Roof Panels - Small Roof
Part 2
E: Place one Short Panel Left on Small Roof Rafter Assembly so it overlaps the Long Panel Left and it is flush
to the sides of (438) Rafter Corner Left and a slight overhang at the bottom of the Fascia Beam Assembly.
There should be no overhanging at the corners. (fig. 12.3 and 12.4)
F: Place one Short Panel Right on Small Roof Rafter Assembly so it overlaps the Long Panel Right and it is
flush to the side of (439) Rafter Corner Right and a slight overhang at the bottom of the Fascia Beam Assembly.
There should be no overhanging at the corners. (fig. 12.3 and 12.4)
G: Attach all panels to Small Roof Rafter Assembly with 31 #8 x 1" Roofing Screws in locations shown in fig.
12.3. Do not place any screws along the bottom row. Be sure not to overtighten screws.
(440)
Rafter
H: Repeat Steps E - G for both Small Roof Rafter Assemblies. (hidden)
Long Panel Long Panel
(438) Rafter Left t Right
Short Panel Corner Left
(439) Rafter
Fig. 12.3 Left (hidden) Corner Right
, (hidden)
,
,
,
Fascia Beam
Assembly
Panels overlap
at the seams
Fig. 12.4
#8x1"
Roofing Short Panel
Screws (x 31
per assembly) Right
OF
Panels flush
to corners, no
overhang DO NOT overtighten
screws, could cause
damage to roofing
material
Fascia Beam •
Assembly No screws along bottom row
Roof Parts
2 x Short Panel Left
2 x Short Panel Right
Hardware
62 x #8 x 1" Roofing Screw
35 support@yardistrystructures.com
Step 13: Attach Ridge Clips and Roof Edges - Small Roof
A: Place one Roof Edge Left 72.2 and one Roof Edge Right 72.2 on the bottom of each Small Roof Rafter
Assembly so the ends are flush with the outside ends of the Fascia Beam Assembly and meet tight in the centre.
Attach both Roof Edges with 17 #8 x 1" Roofing Screws per Small Roof Rafter assembly. (fig. 13.1 and 13.2)
B: Place one Weather Seal on the inside of each Ridge Clip 102.5 then place one Ridge Clip 102.5 on each
side of each Small Roof Rafter Assembly so they cover the panels and attach with five #7 x 18mm (3/4") Wood
Screws per Ridge Clip 102.5. (fig. 13.1, 13.3 and 13.4)
Flush
Fig. 13.1 Ridge Clip
102.5
#7 x 18 mm (3/4")
Wood Screws (x 5
per side)
Flush
INOWN
Roof Edge
Right 72.2
Fascia Beam
Assembly
#8x 1" Roofing
Ridge Clip Screws (x 17)
102.5 Flush Roof dge
Left 72.2
Roof Edge
Right 72.2
Fig. 13.2
Roof Edge
Left 72.2
Fascia Beam Fig. 13.4
Assembly Side View
Ridge
Clip
Tight at centre 102.5
Fig. 13.3 Panels
Underneath,
Side View Weather
Seal
Ridge Clip
102.5 Weather
Seal #7 x 18mm (3/4")
Wood Screws (x 5
per side)
Componets:
2 x Roof Edge Left 72.2
2 x Roof Edge Right 72.2
4 x Ridge Clip 102.5
4 x Weather Seal
Hardware
34 x #8 x 1" Roofing Screw
20 x #7 x 18 mm (3/4") Wood Screw
36 support@yardistrystructures.com
Step 14: Attach Roof Panels - Large Roof
Part 1
A: Place one Middle Panel on the front of one Large Roof Rafter Assembly so it slightly overhangs the top of
(434) Top and an overhang at the bottom of the Large Fascia Beam Assembly. Holes should line up with (440)
Rafter and (430), (431) and (432) Straps (fig. 14.1)
B: Place one Long Panel Left and one Long Panel Right on each side of Middle Panel so they overlap the
Middle Panel and are flush to the sides of (438) Rafter Corner Left and (439) Rafter Corner Right and an
overhang at the bottom of the Large Fascia Beam Assembly. Attach with two #8 x 1" Roofing Screws per panel
in the places shown below. Be sure not to overtighten screws. (fig. 14.2)
Slight
(434) Top overhang
Fig. 14.1 (hidden)
(430) Strap
Short - Large
Roof
(432) Strap
Right -
(431) Strap Large Roof
Left - Large
Roof
Large Fascia (440)
Beam Assembly Rafter
(hidden) Will overhang (440) Middle Panel
Rafter
DO NOT overtighten
screws, could cause
damage to roofing Middle anel
material Panels overlap
at the seams Flush Fig. 14.2
Flush
((439) Rafter
438) Rafter
Corner Right
Corner Left
Long Panel
Large Fascia Left Will overhang
Long Panel Right
Beam Assembly
Roof Parts Hardware
2 x Middle Panel
8 x #8 x 1" Roofing Screw
2 x Long Panel Left
2 x Long Panel Right
37 support@yardistrystructures.com
Step 14: Attach Roof Panels - Large Roof
Part 2
C: Place one Short Panel Left so it overlaps the Long Panel Left and it is flush to the sides of (438) Rafter
Corner Left and one Short Panel Right so it overlaps the Long Panel Right and it is flush to the side of (439)
Rafter Corner Right. There will be a slight overhang at the bottom of the Large Fascia Beam Assembly. There
should be no overhang at the corners. (fig. 14.3 and 14.4)
D: Make sure all panels fit properly then attach with 42 #8 x 1" Roofing Screws. Be sure not to overtighten
screws (fig. 14.3 and 14.4)
Notice there are no screws along the bottom row.
E: Repeat Steps A - D for both Large Roof Rafter Assemblies.
Middle Panel
Fig. 14.3
Long Panel Right
Long Panel Left + (439) Rafter
(438) Rafter + Corner Right
Corner Left (hidden)
+
(hidden)
Short Panel Panels flush
Left to corners, no
overh ng
Large Fascia
Beam Assembly
#8 x 1" Roofing Screws
(x 42 per assembly)
No screws along Short Panel
bottom row Right
#8x1"
Roofing
Screws
Fig. 14.4
DO NOT overtighten
screws, could cause
damage to roofing
material
Panels overlap
at the seams
Roof Parts
2 x Short Panel Left
2 x Short Panel Right
Hardware
84 x #8 x 1" Roofing Screw
38 support@yardistrystructures.com
Step 14: Attach Roof Panels - Large Roof
Part 3
F: On one Large Roof Rafter Assembly place one (463) Spacer Top flush to the outside edges and centred on
(434) Top then attach with three #8 x 2-1/4" Wood Screws. (fig. 14.5 and 14.6)
Wood Parts
1 x (463) Spacer Top
(463)
Fia. 14.6 Spacer Top
Hardware
3 x #8 x 2-1/4" Wood Screws
39 support@yardistrystructures.com
Step 15: Attach Ridge Clips and Roof Edges - Large Roof
Componets:
2 x Roof Edge Left 72.2
2 x Roof Edge Right 96.2
4 x Ridge Clip 102.5
4 x Weather Seal
Hardware
40 x #8 x 1"Roofing Screw
20 x #7 x 18 mm (3/4") Wood Screw
40 support@yardistrystructures.com
Step 16: Attach Roof Panels to Frame
Part 1
1 � M
.p— 1wJ
A: From inside the Post Assemblies measure 4' 11" to mark the centre of each Short Beam Assembly. (fig. 16.1)
B: With all four assemblers place one Large Roof Panel Assembly with Roof to Beam Brackets just in front of the
Post Assemblies then raise it up so it is centred on the Long Beam Assembly. (fig. 16.1)
Fig. 16.1 Large Roof Panel Long Beam
Assembly Assembly
Short Beam
Assembly
Mark centre
location
In front
of Post
Short Beam Assembly
Assembly
Mark centre
• • • . location
Long Beam
Assembly
One assembler to support
roof panel(s) at all times until
secure
Post
Assembly
41 support@yardistrystructures.com
Step 16: Attach Roof Panels to Frame
Part 2
ii
.p
Lwj L
C: Lift a Small Roof Panel Assembly with Roof to Beam Brackets over Short Beam Assembly taking care not to
drag the panel on the beams. Make sure the middle Roof to Beam Bracket lines up to the centre mark and the
Rafter Corners are flush with each other. One person must remain on the centre ladder to hold both panels in
place until three panels are up and secure. (fig. 16.2, 16.3 and 16.4)
D: Starting at the bottom and working up connect Large Roof Panel Assembly to Small Roof Panel Assembly
through the Rafter Corners with three 1/4 x 2-3/4" Hex Bolts (with two 1/4-5/16" large washers and one 1/4" lock
nut). To align bolt holes helper in the centre may have to push up the centre of the panels and others make sure
corners are aligned. Make sure all bolts are tight. (fig. 16.2 and 16.5)
Make sure
corners are Large Roof
aligned Panel Assembly Fig. 16.2
Fig. 16.3 Line middle
bracketto
centre mark
Small Roof
Panel
Assembly Roof to
Beam
Bracket
Beam
Assembly
Fig. 16.5
1/4-5/16"
Large Washer
1/4" Lock
One assembler Nut
to support roof
panel(s) at all
times until secure Small Roof
Panel Assembly
Large Roof
Panel
Assembly
Fig. 16.4
Small Roof
Panel
Assembly
Rafter 1/4 x 2-3/4"
Corner Hex Bolt
Rafter Large Roof Start at bottom and
Corners Panel work up the rafters
Assembly
Hardware
3 x 1/4 x 2-3/4" Hex Bolt
(1/4-5116" large washer x 2, 1/4" lock nut)
42 support@yardistrystructures.com
Step 16: Attach Roof Panels to Frame
Part 3
lID
E: Lift second Large Roof Panel Assembly with Roof to Beam Brackets over Large Beam Assembly taking care
not to drag the panel on the beams then set in place beside the Small Roof Panel Assembly. (fig. 16.6)
F: Starting at the bottom and working up connect Large Roof Panel Assembly to Small Roof Panel Assembly
through the Rafter Corners with three 1/4 x 2-3/4" Hex Bolts (with two 1/4-5/16" large washers and one 1/4" lock
nut). To align bolt holes helper on the centre ladder may have to push up in the centre of the panels and others
make sure corners are aligned. Make sure all bolts are tight. (fig. 16.7)
Small Roof
Fig. 16.6 Panel Assembly
Large Roof
W Panel Assembly
Fig. 16.7
1/4-5/16"
Large Washer
1/4" Lock
Nut
Large Roof
Panel Assembly
Small Roof
Panel Assembly
1/4 x 2-3/4"
Hex Bolt
Rafter
Corner
Hardware
3 x 1/4 x 2-3/4" Hex Bolt
(1/4-5116" large washer x 2, 1/4" lock nut)
43 support@yardistrystructures.com
Step 17: Roof Peak Assembly
A: Insert two Carriage Bolts with Contoured Washers through the top of Peak Cap Long, into Peak Post then
Spring Clip. The Spring Clip holds the assembly together. (fig. 17.1)
B: Insert one 1/4" Nut into each Peak Loop. Be careful nut is loose and will fall out until attached to Peak Cap
Assembly. (fig. 17.2)
Contoured
Washer
Carriage
Bolt
Peak Cap
Long
Fig. 17.1
Contoured
Washer
Peak
Post
Spring ZZ
Clip
Fig. 17.2
Peak
Loop
1/4" Nut
Componets:
1 x Roof Peak Set 1 x Peak Cap Long
2 x Carriage Bolt 2 x Peak Post
2 x Contoured Washer
2 x Peak Loop
2 x Spring Clip
2 x 1/4"Nut
44 support@yardistrystructures.com
Step 18: Attach Roof Peak to Roof Panels
Components: Hardware
4 x Roof Peak Brackets 6 x #10 x 1-114" Pan Screw
45 support@yardistrystructures.com
Step 19: Attach Final Roof Panel
Part 1
lID
46 support@yardistrystructures.com
Step 19: Attach Final Roof Panel
Part 2
Hardware
6 x 1/4 x 2-3/4" Hex Bolt
(1/4-5116" large washer x 2, 1/4" lock nut)
47 support@yardistrystructures.com
Step 19: Attach Final Roof Panel
Part 3
C: On the Small Roof Rafter Assembly just installed, centred and flush to the bottom of (442) Rafter Short Right,
(441) Rafter Short Left and (440) Rafter attach one Roof to Beam Bracket per board with one #8 x 1" Pan Screw
in the bottom hole and one #12 x 1-1/2" Pan Screw in the top hole per bracket. (fig. 19.5)
Attach to Rafter Short Right,
Fig. 19.5 Rafter Short Left and Rafters
I
Flush
#12 x 1-1/2"
Pan Screw
#8 x 1" (x3)
Pan Screw
(x3)
I
I
Parts removed
for clarity
Roof to
Beam
Bracket
Hardware
3 x #8 x 1"Pan Screw
3 x #12 x 1-1/2" Pan Screw
3 x Roof to Beam Bracket
48 support@yardistrystructures.com
Step 20: Secure Roof Corners
WIN
Hardware
8 x #8 x 2-1/2" Wood Screw
8 x #8 x 1"Pan Screw
49 support@yardistrystructures.com
Step 21: Attach Corner and Beam Caps
lID
Componets: Hardware
4 x Corner Cap 16 x #8 x 3/4" Sheet Metal Screw
50 support@yardistrystructures.com
Step 22: Secure Roof to Beam Brackets
lID
A: From inside the assembly attach Roof to Beam Brackets to Beam Assemblies with two #12 x 1-1/2" Pan
Screw per bracket. (fig. 22.1 and 22.2)
Fig. 22.1
Incirla Viaw
Hardware
28 x #12 x 1-1/2" Pan Screw
51 support@yardistrystructures.com
Step 23: Secure Roof Peak Brackets
7 Nil
AV I
ago
A: Tighten the six screws in Roof Peak Brackets then attach to Corner Rafters in the remaining holes with ten
#10 x 1-1 /4" Pan Screws. (fig. 23.1)
Fig. 23.1 Roof Peak
Bracket
Rafter
Corner Rafter
Corner
Rafter
Rafter Corner
Corner
Roof Peak
#10 x 1-1/4" Bracket
Pan Screw x 10
Hardware
10 x #10 x 1-1/4" Pan Screw
52 support@yardistrystructures.com
Step 24: Attach Ridge Caps to Roof Panels It *
A: Slide one Ridge Cap Long 81.5 over the Ridge Clips, with cut end leading, on each corner of the assembly
from the bottom up. Slide Ridge Cap Short 25.2 over the Ridge Clips leading with the insert end to push the
Ridge Cap Long 81.5 to the top, lifting Peak Cap Long by pushing up the Peak Loop so Ridge Cap Long 81.5s fit
under Peak Cap Long. Attach with two #8 x 3/4" Sheet Metal Screws per Ridge Cap set. (fig. 24.1, 24.2, 24.3,
24.4 and 24.5)
B: Tighten Loop to secure Roof Peak Set.
Peak Cap
Fig. 24.1 Long
Fig. 24.3
slide on easier use a
lubricant such as liquid soap.
Ridge Clip
102.5 N
Fia. 24.2
Ridge Cap
Long 81.5
#8 x 3/4" Sheet Metal Screw
Ridge Cap
Short 25.2
Ridge Cap
Long 81.5
Ridge Cap
Short 25.2
Folded
End
Componets: Hardware
4 x Ridge Cap Long 81.5 8 x #8 x 3/4" Sheet Metal Screw
4 x Ridge Cap Short 25.2
53 support@yardistrystructures.com
Step 25: Attach Tie Wrap Brackets and Ties
7m
A: Attach one Tie Wrap Bracket to each end of
one (461) Tie with one #10 x 1-1/4" Pan Screw
per bracket using the inside holes. (461) Tie is
tight to end of bracket. (fig. 25.1, 25.2 and 25.3)
B: With a helper place (461) Tie with brackets
against a (440) Rafter on each Large Roof Panel
so (461) Tie is tight to (440) Rafters and level.
Attach Tie Wrap Bracket to (440) Rafters with two
#10 x 1-1/4" Pan Screws on both sides of each
bracket (fig. 25.1, 25.2 and 25.3)
C: Pre -drill with a 1/8" drill bit and secure Tie
Wrap Brackets to (461) Tie and (440) Rafter with
one #10 x 2-1/2" Pan Screw per bracket. (fig.
25.1, 25.2 and 25.3)
D: Repeat Steps A to C for a second (461) Tie.
#10 x 1-1/4"
Pan Screw
Tie Wra
Bracket
#10 x 2-1/2"
Pan Screw
Fig. 25.3
#10 x 1-1/4"
Pan Screw
4MV/
#10 x 1-1/4"
Pan Screw
(440)
Rafte
1
E
I area Rnnf Fig. 25.1 Large Roof Panel
#10 x 1-1/4"
Pan Screw
#10 x 2-1/2" Pan Screw Pan Screw
(pre -drill before installing)
Wood Parts Hardware Comoonets:
2 x (461) Tie 31.8 x 88.9 x 2336.8 mm (1-1/4 x 3-1/2 x 92") 20 x #10 x 1-1/4" Pan Screw 4 x Tie Wrap Bracket
4 x #10 x 2-1/2" Pan Screw
Tie
54 support@yardistrystructures.com
Step 26: Metal Hooks and Plaque
Part 1
7E
A: Two 50 mm Hooks are included with this unit for attaching wiring. They can be placed anywhere along the
Rafter Corners as needed. Pre -drill with a 1/8" drill bit before installing.
(fig. 26.1 and 26.2)
B: One Eye Lag is included with this unit for hanging items with a maximum
weight of 22 Ibs (10 kg). Pre -drill
with a 1/8" drill bit into centre of (463) Spacer Top then install Eye Lag.
(fig. 26.1 and 26.3)
(463) Spacer
Top Fig. 26.1
Note: DO NOT ATTACH
ANY PRODUCT WHICH
Parts removed
WEIGHS GREATER
for clarity
THAN 22 LBS (10 KG)
TO THE EYE LAG
Rafter
Corner
Fig. 26.3
Note: We have provided two
(463) Spacer
50 mm hooks for optional use
Top
to hold in place any wires if
Fig. 26.2 required. These hooks are
not designed to hold any
Centre
heavy products such as
lights, flower pots, etc.
Eye
Lag
50 mm Hook
Hardware
2 x 50 mm Hooks
1 x Eye Lag
55 support@yardistrystructures.com
Step 26: Metal Hooks and Plaque
Part 2
Hardware
2 x #8 x 1"Pan Screw
1 x Gazebo ID Plaque
56 support@yardistrystructures.com
YWISTRYe
Yardistry0375 Sligo Road West, P.O. Box 10, Mount Forest, ON Canada NOG 2L1
Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
Costco Wholesale UK Ltd /
Costco Online UK Ltd
Hartspring Lane
Watford, Herts
WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk
Costco Wholesale Japan Ltd
3-1-4 I keg am i-S h i n c h o
Kawasaki-ku, Kawasaki-shi,
Kanagawa 210-0832 Japan
0570-032600
www.costco.co.jp
Costco Wholesale Canada Ltd.*
415 W. Hunt Club Road
Ottawa, Ontario
K2E 1 C5, Canada
1-800-463-3783
www.costco.ca
* faisant affaire au Quebec sous
le nom les Entrep6ts Costco
Costco Wholesale Spain S.L.U.
Poligono Empresarial Los
Gavilanes
C/ Agustin de Betancourt, 17
28906 Getafe (Madrid) Espana
NIF: B86509460
900111 155
www.costco.es
Costco Wholesale Korea, Ltd
40, Iljik-ro
Gwangmyeong-si
Gyeonggi-do, 14347, Korea
1899-9900
www.costco.co.kr
Importado por:
Importadora Primex S.A. de C.V.
Blvd. Magnocentro No. 4
San Fernando La Herradura
Huixquilucan, Estado de Mexico
C.P. 52765
RFC:IPR-930907-S70
(55)-5246-5500
www.costco.com.mx
Costco Wholesale Iceland ehf
Kaupt6n 3-7, 210 Gardabaer
Iceland
www.costco.is
Costco Wholesale New Zealand Limited
67 Maki Street
Massey, Auckland 0814
New Zealand
MADE IN CHINA • FABRIQUE EN CHINE • HECHO EN CHINA
Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road
Lidcombe NSW 2141
Australia
www.costco.com.au
Costco France
1 avenue de Br6hat
91140 Villebon-sur-Yvette
France
01 80 45 01 10
www.costco.fr
Shanghai Minhang Costco Trading Co., Ltd
No. 235, ZhuJian Road
Minhang District, Shanghai
China 201106
+86-21-6257-7065
57 support@yardistrystructures.com
NOTES
58 support@yardistrystructures.com
NOTES
59 support@yardistrystructures.com
ZIP/Postal Code - Codigo Postal - Country - Pais - Pays
ZIP/Code postal
I
YA 71,
X1 JVISTRY.
I
I
I
Customer Registration Card - Tarjeta de Registro del Cliente - Carte d'inscription du client I
I
I
I
First Name - Primer Nombre - Prenom Initial - Incial - Initiale Last Name - Apellido - Nom de famille I
I
I
Street - Calle - Rue PO Box - Casilla postal - Apt. No. - App.
Boite postale
I
I
I
I
City - Ciudad - Ville State/Province - Estado/Provincia - Etat/Province
I
I
I
I
I
I
I
I
I
I
E-mail Address - Direccidn de E-mail - Adresse courriel Telephone Number - No. de Telefono - N° de telephone
I
Model Name - Nombre del Modelo -
Nom du modele
Model Number (from front cover) - NOmero de Modelo (de la portada) -
No du modele (page de couverture)
Date of Purchase - Fecha de Compra - Date d'achat
(mm/dd/yyyy) (mm/dd/aaaa) (mm/jj/aaaa)
Place of Purchase - Comprado a - Lieu d'achat
Comments - Comentarios - Commentaires:
o'
w�
0
Mail To - Enviar por Correo a - Envoyer par courrier a: ZI
Yardistry Online Registration - Registro online - Enregistrement en ligne: WI
375 Sligo Road West, PO Box 10 www.yardistrystructures.com/warranty al
Mount Forest, Ontario, Canada, NOG 21-0 Hours/ Heures/ Horas: 8:30 am - 5:00 pm EST al
Attention: Consumer Relations (excl. holidays/ hors fours feries/ excepto los dias Jt
Atencion a: Servicio de Atencion al Cliente festivos)
A I'attention de: Service a la Clientele English and French Spoken / Anglais et frangais parles / Ingles y frances hablado �I
o�
u
wl
Yardistry would like to say "Thank you" for your time and feedback. ZI
Yardistry quiere 'Agradecerle" par su tiempo y su opinion. of
a�
Yardistry aimerait vous remercier d'avoir pris le temps de repondre au Bondage.
07/24/2020 ul
MADE IN CHINA / FABRIQUE EN CHINE / HECHO EN CHINA
60 support@yardistrystructures.com