FIR2023-0037_Fire_Alarm_Battery_Calculations_4.13.2023_2.45.09_PM_3482071W I�II i! R:111 flu,1111111 _ �7 i! III U 1/
INSTALLATION OF NEW AES 7707P-88-UPL FIRE RADIO
@ 615 GLEN STREET, EDMONDS, WA 98020-3028
CONNECTED TO EXISTING:
AES TROUBLE OUTPUT CONNECTED TO EXISTING SYTEM
BY THE FOLLOWING METHOD: Zone existing on panel
ACCT# LAC857797 C/S: ALARM CENTER
RANGE TEST: 7 NETCOM: 5
7067 INTELLITAP: YES 7770 FIRETAP: NO
DEDICATED BREAKER: PANEL#: HOUSE CKT#: UNKNOWN
/ADRIAN M. STEIK
Senior Engineering Technician, Level 4
NICET Certifcation Number: 093706
Authorizing Signature: 6-d i^'�
UHF Antenna Options (450-480 MHz)
Antenna dB
Construction
Usage
Length
2.5 dB Case Top Flex Tamper Resistant (1 11 2)
Vinyl Clad
Indoor
11 in.
3 dB Stealth (Not Shown Below) (3)
Vinyl Clad
Indoor
1.5 ft.
3 dB Standard Gain (4&5)
Steel Mast
Indoor
1.5 ft.
5 dB High Gain (4)
Steel Mast
Indoor
3 ft.
6 dB Rugged High Gain(4)
Fiberglass Mast
In/Outdoor
4.5 ft.
7 dB Rugged Higher Gain(4)
Fiberglass Mast
In/Outdoor
6 ft.
9 dB Central Station High Gain(')
Fiberglass Mast
In/Outdoor
6 ft.
Notes: 1. This antenna was evaluated by UL and approved for use in a UL 864 Edition 9 system.
2. Included standard Tamper Resistant antenna, mounts on Alarm Unit's enclosure.
Includes cable.
3. Mounts in attics, vents, walls, behind drapes, ect. Includes 10-foot cable.
4. Requires cable (See Section 1.10). Usually requires user supplied mounting hardware
such as a pole with mounting brackets/hardware.
5. Antenna is intended for outdoor use, supplied mount is intended for indoor use as coax
connection is exposed. To use outdoors, connection must be sealed with a suitable
product such as a self -fusing tape to protect against moisture.
AES
FRCP
FACP/RDACT
LAYOUTS
ljoin__2
AES"n
CORPORATION
CURITY
01111WATutn
O
FACP ROOM LAYOUT
w/ DETECTOR
Battery Capaciry Calculator Instructions:
1) Select the AES product from the AES Product field.
2) Select if Ethernet Cable is required during normal operation.
This only applies to 2.0 subscribers.
3) Enter the # of hours of backup time required. AES products are
UL listed for 24 hours operation on battery backup.
4) The calculator will return the recommended battery capacity.
AES Product
Ethernet Cable
Required
7707P 88-ULP-M
Yes
Standby Current
Ethernet Current
Total Standby
AlarmfTransmit
OTY
Total Alarm
(Amps)
(Amps)
Current (Amps)
Current (Amps)
Current (Amps)
0.348
0.015
— 0.363
0.866
x
1I
= 0.868
Total Standby Current (Amps)
0.363
Total Alarm Current (Amps)
0.868
# Hours Backup
Standby Current
Required Standby
Required Alarm
Alarm7Transmit
Required Alarm
TiCapacity
me
(Amps)
(Amp Capacity
ys)
Time (Hours)
I
Current(Amps)
(Amp -Hours)
24 1
x 1 0.363
8.7
0.25
x
0.868
0.2
Required Standby
Required Alarm
Total Required
Capacity
Capacity
Backup Capacity
(Amp -Hours)
(Amp -Hours)
(Amp -Hours)
8.7
02
= 8.9
Total Required
Recommended
Backup Capacity
Recommended
Minimum Battery
(Amp -Hours)
Safety Factor
Capacity
(Amp -Hours)'
8.9
x 120%
= 10.7
"The battery requirements presented here are only AES
recommendations. For UL listed battery requirements
please read the product Installation and Operation Manual.