Loading...
REVIEWED BLD2023-0979+Manufacturer_Specifications_and_Installation_Instructions+8.2.2023_10.52.37_AM+3702962[I-1111jo • CONTEMPORARY DRINKING FOUNTAINS A INSTALLATION/MAINTENANCE INSTRUCTIONS RECEIVED BLD2023-0979 GYE14 Series Aug 02 2023 CITY OF EDMONDS DEVELOPMENT SERVICES DEPARTMENT Wall Mounted Bottle Filler With Angled Drinking Fountain REVIEWED BY CITY OF EDMONDS GYE15-111 SHOWN TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER: 1.800.591.9360 Technical Assistance Fax: 1.626.855.4894 IMPORTANT: INSTALLATION AND SITE PREP FOR FREEZE RESISTANT OPTIONS "-FRA" WILL DIFFER FROM STANDARD! REFER TO DESIGNATED FREEZE RESISTANT INSTALLATION DETAILS PRIOR TO ROUGH -IN AND FIXTURE INSTALL FOR -FRA SERIES OPTIONS. FOR ADDITIONAL INFORMATION VISIT: www.MurdockMfg.com/Resources OR CONTACT YOUR LOCAL SALES REPRESENTATIVE. NOTES TO INSTALLER: 1. Please leave this documentation with the owner of the fixture when finished. 2. Please read this entire booklet before beginning the installation. 3. Check your installation for compliance with plumbing, electrical and other applicable codes. LIMITED WARRANTY - UNITED STATES & CANADA Murdock warrants that its products are free from defects in material orworkmanship under normal use and service fora period of one year from date of shipment from the factory. Murdocks's liability under this warranty shall be discharged solely by repair or replacement of defective material, provided Murdock is notified in writing within the time periods described above. This warranty does not cover installation or labor charges and does not apply to materials, which have been damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard or non-compliance with these instructions will constitute an abnormal use condition and void the warranty. Stainless steel must be protected on jobsite during construction and must be properly maintained after the water has been introduced into the water cooler or drinking fountain, or Murdocks's limited warranty is void. LIMITED EXPORT WARRANTY - One year on parts only. MurdockTM' assumes no responsibility for use of void or superseded data. © Copyright _ Murdock Murdock Mfg., City ofIndustry, CA Member of — NSF/ANSI 61 aeo c�® ® ®'aol`eacl is Morris Group International. Please visit SINCE 1853 www.murdockmfg.com for most current — specifications. — 15125 Proctor Ave, City of Industry, Member of CA, 91746 U.S.A. — Phone 800-591-9360 626-336-4561 7109-611-001 D-12/06/2022 MORIUS GROUP Fax 626-855-4894 INTERNATIONAC www.murdockmfg.com CONTEMPORARY DRINKING FOUNTAINS _ _ _ _ INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 INSTALLATION INFORMATION PRIOR TO INSTALLATION: 1. Read all installation instructions carefully, before proceeding. 2. Carefully remove fixture from packaging, preventing scratching or damage. 3. Units with -SO, -SOC option require six AA alkaline batteries (Not Provided). 4. Provide mounting surface, sufficient to support the fixture and loads on the fixture. 5. Provide rough -ins as shown on the roughing -in and dimensional drawing, including water supply and drain pipe. 6. Completely flush water supply lines of all foreign debris, before connecting to the fixture. INSTALLATION: (see drainage & mounting roughing -in) 1. Create sufficient Blockout Area and mounting preparation according to Rough -In and Dimensional Drawing. 2. Mount and secure Wall Mounting Plate to wall horizontally level as shown in Rough -In and Technical Dimensions. NOTE: Adjust height of bracket if fixture height required differs from dimensions shown. WARNING: Wall Mounting Plate MUST be securely anchored to wall with fasteners sufficient to support a minimum pull-out rating of 1000lbs (454kg). 3. Remove Bottle Filler Bottom Access Panel and set aside in a safe place. Save the screws in a secure location for re -use in later stages of installation. 4. Prepare Fixture Assembly for mounting by ensuring all supply and waste connections are securely attached and ensuring that the 1/2"-13 x 2" Long Bolts (Provided) are loosely attached to the fixture. 5. Mount and secure Fixture Assembly to Wall Mounting Plate by making sure that all four 1/2"-13 x 2" Long Bolts (Provided) align and secure successfully. 6. Make up 3/8" OD Supply Connection to water supply, and 1-1/4" OD waste to P-Trap (by others). Attach Bottle Filler Bottom Access Panel using previously set -aside screws. START UP: Air within the bottle filler system or the structure supply piping will cause an irregular spout outlet stream until purged out by incoming water. Press and hold pushbutton until steady water stream is achieved. OPERATION INSTRUCTIONS: Hand operation: Hold container to be filled just below the filler tube in the center of the unit, then depress pushbutton. When the container is almost filled, release the pushbutton. Refer to Flow Adjustment detail on Parts Drawing if needed. Sensor Operation: Hold container to be filled just below the sensor in the center of the filler spout and then move the container upward and water flow will start automatically. When the container is almost filled, lower the container below the sensor until the water stops flowing. (See label on the bottle filler) Aluminum Ni Sensor Fill Spout I a I Drain MURDOCK MFG. - 15125 Proctor Avenue • City of Industry, CA 91746 USA Phone 800-453-7465 or 626-333-2543 - Fax 626-855-4860 • www.murdockmfg.com Member °f MORRIS GROUP 7109-611-001 Page 2 of 20 Date: D-11/29/2022 • 1 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 ROUGH -IN AND TECHNICAL DIMENSIONS Tna VIEW 55° 0 12" [305] *502" (1284) 4 ° a PRnMT VIEW *33" *27" [838] [686] GYE14-R SHOWN NOTES: 1. 1/4" THICK STAINLESS STEEL MOUNTING PLATE 2. REMOVABLE ACCESS PANELS 3. BOTTLE FILLER SPOUT 4. BOTTLE FILLER PUSHBUTTON 5. DRINKING BUBBLER ~122" (318)--- I �_4" (19) 62" (165) 62" (165) *544" [1391 ] 6. DRINKING FOUNTAIN PUSHBUTTON WITH CARTRIDGE VALVE 7. OPTIONAL -PT 1-1/4" OD P-TRAP SHOWN 8. SUPPLY CONNECTION 9. INSTALLER PROVIDED WALL ANCHORS AND ANCHORING HARDWARE FOR 017/32" (013.5) FIXTURE MOUNTING * Valve specifications: Minimum/Maximum Pressure 30 to 100 psi. 174" [438] ADA PROFILE CIIIF VIEW GENERAL NOTES: 1. ALL DIMENSIONS ARE IN INCHES [MM]. *2. DIMENSIONS SHOWN ARE FOR RECOMMENDED ADULT HEIGHT. ADJUST VERTICAL DIMENSIONS AS NECESSARY TO COMPLY WITH FEDERAL, STATE, & LOCAL CODES. 3. STOP VALVE NOT PROVIDED. Murdock Mfg. TM warrants that its products are free from defects in material or workmanship under normal use and service for a period of one year from date of shipment. Murdock's liability under this warranty shall be discharged solely by replacement or repair of defective material, provided MurdockTM is notified in writing within one year from date of shipment, F.O.B. Industry, California. 271„ 2 (699) MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIO 7109-611-001 Page 3 of20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 FIXTURE MOUNTING AND ANCHORING 1 Make up Mounting Rough -In and Blockout Area into sufficient wall backing. 1211 ' Finished Wall O 1,, 62 44 [165] TYP [108] BLOCKOUT I [772" 261 „ 27" Finished 4 [191] [686] Floor [667] BLOCKOUT O2 a a a 1O Mounting Plate O1/2" Flat Washer Og 1/2"-13 x 2" Long Bolts (Provided) 3 Secure Wall Mounting Plate to the Finished Wall using Installer Provided Hardware. 2 1 ° 3 3 ° ° ° ° ° IMPORTANT: Industry standard wall backing for wall hung fixtures is required. Installer provided wall anchors and wall anchoring hardware must IMPORTANT. appropriate for wall construction and have a minimum pull-out rating of 1000lbs (454kg). OFinished Wall OFinished Floor 03 01 /2" Wall Anchors (Not Provided) Install 1/2"-13 x 2" Long Bolts (Provided) into the I Mounting Plate from rear. SIDE VIEW (Ta E: It is recommended to level and plumb Mounting Plate prior to mounting fixture mbly. 1O Finished Wall OMounting Plate 03 01 /2" Installer Provided Wall Fasteners/Anchors MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 4 of 20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 FIXTURE MOUNTING AND ANCHORING (CONTINUED) 4 Remove Bottle Filler Bottom Access Panel and set aside for later Installation. 1O Fixture Assembly 02 Mounting Plate 03 1/2"-13 UNC x 2" Long, Bolts provided 1O Fixture Assembly OBottle Filler Bottom Access Panels O#10-32 UNF Hex Screws (Provided) q OTE: It is recommended to rough -in supply d waste lines ensuring Mounting Plate is vel and plumb prior to securing fixture semblyto Mounting Plate. M 5 Mount Fixture Assembly onto the Mounting Plate by sliding unit over the 1 /2"-13 x 2" Long Bolts. 2J 1 o a o� a a 0 3 r� MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 5 of 20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 FIXTURE MOUNTING AND ANCHORING (CONTINUED) 6 Secure Fixture Assembly to Mounting Plate using 1/2" Hardware (Provided). 6 5 p 2 4 3 2 d d 4 1 d d p Emp d d O a A d d p DETAILA p 4 Make up 3/8" OD Supply Connection to water supply, and 1-1/4" OD waste 7Ato P-Trap (by others). Attach Bottle Filler Bottom Access Panel using previously set -aside screws. 6 5 4 4 4 B STANDARD MODELS 0) 1/2"-13 x 2" Long Bolts (Provided) O1/2" Flat Washers (Provided) O1/2" Helical Lockwasher (Provided) 4O 1/2"-13 UNC Hex Nut (Provided) OFinished Wall OFixture Assembly O3/8" OD Supply Connection O$ 1-1/4" OD Waste Outlet for P-Trap Behind Wall (Standard) P-Trap provided by others NOTE: FOR MODELS WITH (-PT) P-TRAP OPTION, REFERTO STEP 7B. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 6 of 20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14-PT FIXTURE MOUNTING AND ANCHORING (CONTINUED Make up 3/8" OD Supply Connection to water supply, and 1-1/4" OD 7B Optional P-Trap Waste Outlet (Provided). Attach Bottle Filler Bottom Access Panel using previously set -aside screws. 2 1 44 3 4 B � 4 DETAIL B OPTIONAL 1-1/4" O.D. P-TRAP MODELS WITH -PT OPTION OFinished Wall OFixture Assembly O3/8" OD Supply Connection O1-1/4" OD Waste Outlet with Optional P-Trap (Provided) MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 7 of 20 Date: D-11/29/2022 CONTEMPORARY DRINKING FOUNTAINS _ _ _ _ INSTALLATION/MAINTENANCE INSTRUCTIONS PUSH -IN FITTING INSTALLATION NOTE: FITTINGS AND TUBE SHOULD BE KEPT CLEAN, BAGGED AND UNDAMAGED PRIOR TO INSTALLATION. TO CUT TUBE: Cut to fit length of 1/4" PE tubing and remove any burrs or sharp edges. Ensure that the outside diameter is free from score marks. Tube ends should be square. INSERTING THE TUBE: 1. Firmly and fully insert the tubing end into the push -in fitting up to the tube stop located approximately'/z" deep. 2. Pull on the fitted tubing to ensure it is secure. Tube should not come free from the fitting. Water test the connection assembly prior to leaving the site to ensure there are no leaks. DISCONNECTING THE TUBE: To disconnect the tube from the fitting ensure that the water line is depressurized. Push collet square towards the push -in fitting body and hold. While holding the collet in, pull on the PE tubing to remove from the push -in fitting. os. COLLET COI O-RING O-RING TUBE STOP � � '`' COLLET4 MURDOCK MFG. - 15125 Proctor Avenue • City of Industry, CA 91746 USA Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member °f MORRIS GROUP 7109-611-001 Page 8 of 20 Date: D-11/29/2022 CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 TROUBLESHOOTING AND MAINTENANCE TROUBLESHOOTING:. 1. RESTRICTED OR NO WATER FLOW: a. Ensure Water Supply service stop valve is fully open. b. Verify minimum 20 psig supply line flow pressure. c. Check for twist or kinks in spout tubing. d. Check the water inlet "Y" strainer. Sediment from the main supply can get trapped in the screen along with installation materials such as pipe dope and flux. The screen should be cleaned and checked on a regular basis and replace if needed. e. Flow control in solenoid valve outlet elbow clogged remove & clean. 1. IF LIGHT WITHIN SENSOR DOES NOT FLASH ONCE WHEN USER IS WITHIN RANGE: a. Verify 9VDC output of battery pack. b. Replace defective batteries. c. Sensor in "Security Mode" after 30 seconds of constant detection. Remove source of detection and wait 30 second before checking. d. Sensor is picking up a highly reflective surface. Eliminate cause of reflection and wait 30 seconds before checking. 2. IF LIGHT WITHIN SENSOR LENS FLASHES ONCE WHEN THE USER IS WITHIN RANGE: a. Repair bad connection from sensor to solenoid. b. There is debris or scale in the solenoid assembly. Remove solenoid, pull out plunger and spring. Clean with scale remover solution. c. There is debris or scale in center or two holes in convolution of the water diaphragm. Remove and clean. CLEANING & MAINTENANCE GUIDE: For Powder coated units: Units should be cleaned using a mild soap solution with a sponge or cotton cloth. Wipe down surfaces then rinse with clean water. For Stainless steel units: 1. To remove water spots or rust spots, stainless steel cleaner/polish on a cloth is recommended. 2. If there are stubborn spots or if you wish to treat a scratch, synthetic abrasive general purpose pads such as scotch brite are recommended. 3. Apply stainless steel cleaner/polish to the synthetic abrasive pads and carefully rub the panel with the grain. 4. DO NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the Murdock warranty. DO NOT use abrasives on powder coated units. 5. Stainless steel should be kept clean at all times. If a coating of stainless steel cleaner/ polish is maintained, stainless steel surfaces will retain their new, clean & polished appearance indefinitely. 6. Periodically remove access panel of cooler and clean out inline "Y" strainer MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member °f MORRIS GROUP 7109-611-001 Page 9 of 20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 FILTER CARTRIDGE REPLACEMENT 1. Loosen and remove bottle filler side access panel, which allows access to the filter. Turn the inlet valve 1/4 turn clockwise to close. 2. Raise the filter assembly straight up about six inches and while holding the cap firmly, turn the replaceable cartridge filter counterclockwise to remove. 3. Remove and replace the cartridge turning clockwise to secure. 5. Turn inlet valve 1/4 turn counterclockwise to open and test for leaks and proper operation before re -attaching bottle fillers side access panel. WATER VALVE OPEN WATER INLET VALVE CLOSED CARTRIDGE MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 10of20 Date: D-11/29/2022 [I-1111jo • CONTEMPORARY DRINKING FOUNTAINS A INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 DRINKING FOUNTAIN ASSEMBLY: Extended Arm, Pushbutton (Standard), Repair Parts ITEM PART NUMBER DESCRIPTION 1 7000-012-001 DRINKING BUBBLER ASSY, 7/16-20 UNF, SS 2 0152-010-000 #10-32 UNF x 1" LONG HEX FLAT HEAD SCREW 3 7007-011-001 11" DIAMETER ROUND BOWL, SS 4 7000-006-000 FLAT FOAM ADAPTER GASKET 5 0116-003-000 #10-32 UNF x'/i' LONG PHILLIPS HEAD SCREW 6 7000-005-199 1-1/4" NPSM DRAIN ADAPTER 7 2169-000-000 '/4" OD LDPE TUBING 8 7000-420-000 '/4 TURN SHUTOFF VALVE 9 7000-065-001 -CV RECESSED PB W/ CARTRIDGE VALVE ASSY 10 0331-004-000 #10 FLAT WASHER, SS 11 0302-004-000 #10-32 UNF HEX NUT, SS 12 7000-017-001 1-1/4" CLOSE ELBOW, SLIP JOINT 13 JSMBF108-199 ACCESS PLATE, ROUND SIDE MOUNT 14 0112-001-000 #10-32 UNF x 3/8" LONG HEX SCREW 15 0401-128-000 O-RING, WASTE ADAPTER MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 11 of20 Date: D-11/29/2022 • 1 • GYE14 DRINKING FOUNTAIN CARTRIDGE VALVE PUSHBUTTON ASSEMBLY: Repair Parts CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS ITEM PART NUMBER DESCRIPTION 1 7000-050-000 REGULATOR VALVE BODY 2 7000-053-199 JAM NUT, 1-1/4" 3 7000-060-000 FLOW REGULATOR CARTRIDGE (0.5 GPM) 4 7000-051-000 RETAINING NUT, VALVE 5 0411-022-000 FIBER RING 1-3/4" x 1-1/4" 6 0431-222-000 RUBBER GASKET 7 7000-063-199 BRASS RETAINER RING 8 7000-091-001 RECESSED PUSH BUTTON W/ HEX ASSY FLOW ADJUSTMENT MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 12of20 Date: D-11/29/2022 • 1 • GYE14 BOTTLE FILLER VALVE ASSEMBLY: Pushbutton (Standard), Repair Parts CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS ITEM PART NUMBER DESCRIPTION 1 2800-108-001 '/4" JACO INLET ADAPTER ASSEMBLY 2 1895-709-000 '/4" OD x'/4" OD STEM PUSH -IN ELBOW 3 2570-051-001 %" OD PLASTIC ELBOW ASSEMBLY 4 0326-100-000 RETAINING CLIP, AIR -CONTROL VALVE 5 2570-102-001 RH VALVE BODY CLOSED END ASSEMBLY 6 2169-000-000 '/4" OD LLDPE TUBING (BLUE) 7 7012-313-000 WF1 FILTER 1500 GALLON CARTRIDGE 8 1895-710-000 '/4' PUSH -IN UNION TEE 9 7000-021-000 %" NPT "Y" STRAINER 10 1895-123-000 '/4' x 3/8" OD TUBE UNION PUSH -IN CON 11 1895-125-000 '/4' OD x/4' NPT PUSH -IN FITTING 12 7000-420-000 '/4" OD PUSH-IN'/4" TURN SHUT-OFF VALVE MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 13of20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14 BOTTLE FILLER ASSEMBLY: Pushbutton (Standard), Repair Parts i i ITEM PART NUMBER DESCRIPTION 1 1895-709-000 '/<" OD x/4' OD STEM PUSH -IN ELBOW 2 0124-033-000 #8 x 3/4" LONGHD SELF -TAP SCREW 3 7000-006-000 DRAIN ADAPTER GASKET 4 7003-182-000 ACCESS DRAIN, BI-LEVEL, UPPER 5 2566-050-002 BACK OUTLET PUSHBUTTON SUB-ASSY 6 7002-125-002 PUSHBUTTON WELD ASSY MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 14of20 Date: D-11/29/2022 • 1 • GYE14-SOC DRINKING FOUNTAIN ASSEMBLY: Extended Arm, Optional Sensor Operation, Repair Parts 2 3 CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS ITEM PART NUMBER DESCRIPTION 1 7000-012-001 DRINKING BUBBLER ASSY, 7/16-20 UNF, SS 2 0152-010-000 #10-32 UNF x 1" LONG HEX FLAT HEAD SCREW 3 7007-011-001 11" DIAMETER ROUND BOWL, SS 4 7000-006-000 FLAT FOAM ADAPTER GASKET 5 0116-003-000 #10-32 UNF x'/2' LONG PHILLIPS HEAD SCREW 6 7000-005-199 1-1/4" NPSM DRAIN ADAPTER 7 0308-009-000 #8-32 NYLON LOCKNUT 8 0331-023-000 SS WASHER 9 7003-958-199 NANO SENSOR HOLD DOWN BRACKET 10 2563-390-000 STERN NANO SENSOR, BLUE 10 SEC 11 7001-203-199 NANO SENSOR SPACER W/ BUSHING 12 0331-004-000 #10 FLAT WASHER, SS 13 0302-004-000 #10-32 UNF HEX NUT, SS 14 7000-017-001 1-1/4" CLOSE ELBOW, SLIP JOINT 15 JSMBF108-199 ACCESS PLATE, ROUND SIDE MOUNT 16 0112-001-000 #10-32 UNF x 3/8" LONG HEX SCREW 17 0401-128-000 O-RING, WASTE ADAPTER 18 7000-050-001 VALVE CARTRIDGE ASSEMBLY For models with optional -SOC Sensor Operation. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 15 of20 Date: D-11/29/2022 CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS ITEM PART NUMBER DESCRIPTION 1 2800-108-001 '/4' JACO INLET ADAPTER ASSEMBLY 2 1895-709-000 '/4' OD x'/4" OD STEM PUSH -IN ELBOW 3 2570-051-001 %" OD PLASTIC ELBOW ASSEMBLY 4 0326-100-000 RETAINING CLIP, AIR -CONTROL VALVE 5 2570-130-001 9VDC SOLENOID VALVE ASSEMBLY 6 2169-000-000 '/4' OD LLDPE TUBING (BLUE) 7 7012-313-000 WF1 FILTER 1500 GALLON CARTRIDGE 8 1895-710-000 '/4' PUSH -IN UNION TEE 9 7000-021-000 '/4' NPT "Y" STRAINER 10 1895-123-000 '/4' x 3/8" OD TUBE UNION PUSH -IN CON 11 1895-125-000 '/4' OD x%" NPT PUSH -IN FITTING 12 7000-420-000 '/4" OD PUSH-IN'/4' TURN SHUT-OFF VALVE 13 0710-357-001 AA 6-PACK BATTERY HOLDER ASSY • 1 • GYE14-SO BOTTLE FILLER VALVE ASSEMBLY: Optional Sensor Operation, Repair Parts For models with optional -SO Sensor Operation. ME MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 16of20 Date: D-11/29/2022 • 1 • GYE14-SO BOTTLE FILLER ASSEMBLY: Optional Sensor Operation, Repair Parts For models with optional -SO Sensor Operation. CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS i 4 7 i g 3 5 2 8 1 , ITEM PART NUMBER DESCRIPTION 1 7013-013-199 NANO SENSOR SPACER - 2 7013-057-002 NANO SENSOR, w/ WIRES 3 7013-019-199 FOAM TAPE, 7/8" x 1/2" x 1/8" 4 7013-010-199 NANO SENSOR BRACKET 5 0331-023-000 #8 FLAT WASHER, SS 6 6527-108-000 #8 LOCKWASHER, SS 7 0302-003-000 #8-32 UNF HEX NUT, SS 8 1895-709-000 ELBOW, 1/4" PUSH -IN x 1/4" STEM 9 7000-420-000 1/4 TURN SHUTOFF VALVE 10 0124-033-000 #8 x 3/4" LONG FLAT HD SELF -TAP SCREW 11 7000-006-000 DRAIN ADAPTER GASKET 1 TO SOLENOID VALVE i TO BATTERY PACK i i I i i MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 17of20 Date: D-11/29/2022 • CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS GYE14-SO BATTERY REPLACEMENT 1. Loosen and remove bottle filler side access panel and remove battery pack from placed location. Do not disconnect the wires from the battery pack unless necessary. 2. Replace the six alkaline AA batteries while observing polarity. 3. Return the battery pack back to mounted location and test for proper operation. Then attach bottle filler side access panel. MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 18of20 Date: D-11/29/2022 • 1 . GYE14 WASTE ASSEMBLY (STANDARD Connections and Assembly, Repair Parts GYE14-R CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS ITEM PART NUMBER DESCRIPTION 1 0124-033-000 #8 x 3/4" HEX SELF TAPPING SCREW 2 0152-010-000 #10-32 x 1" HEX FLAT HEAD SCREW 3 7000-005-199 DRAIN ADAPTER 4 7000-006-000 DRAIN ADAPTER GASKET 5 7000-017-001 ELBOW, ORING x 1-1/4" COMPRESSION 6 7003-182-000 ACCESS DRAIN, BI-LEVEL, UPPER 7 7003-183-000 ANSI/AHAM CERTIFIED FLEX HOSE, 5/8 x 7/8 8 7003-184-000 7/8" SPRING HOSE CLAMP 9 JSMA2005-001 WASTE TUBING RH ASSY MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com Member °f MORRIS GROUP 7109-611-001 Page 19of20 Date: D-11/29/2022 • 1 • GYE14-PT WASTE ASSEMBLY WITH OPTIONAL P-TRAP: Connections and Assembly, Repair Parts GYE 14-PT CONTEMPORARY DRINKING FOUNTAINS INSTALLATION/MAINTENANCE INSTRUCTIONS ITEM PART NUMBER DESCRIPTION 1 0124-033-000 #8 x 3/4" HEX SELF TAPPING SCREW 2 0152-010-000 #10-32 x 1" HEX FLAT HEAD SCREW 3 7000-005-199 DRAIN ADAPTER 4 7000-006-000 DRAIN ADAPTER GASKET 5 7000-017-001 ELBOW, ORING x 1-1/4" COMPRESSION 6 7003-182-000 ACCESS DRAIN, BI-LEVEL, UPPER 7 7003-183-000 ANSI/AHAM CERTIFIED FLEX HOSE, 5/8 x 7/8 8 7003-184-000 7/8" SPRING HOSE CLAMP 9 MURGRE52-001 RH WASTE TUBING ASSY, GYE10-PT MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA Member of `CJ Phone 800-453-7465 or 626-333-2543 • Fax 626-855-4860 • www.murdockmfg.com MORRIS GROUP INTMNATIONIr 7109-611-001 Page 20 of 20 Date: D-11/29/2022