REVIEWED Marco Ecosmart UC45 SpecsECOSMART UC10/UC45
marco
N
00
Wamm 0,W I Mr.
PRODUCT INFO
FONT DIMENSIONS
PACKAGING
NAME
DIMENSIONS DIMENSIONS TAP TO
PACKAGING
PACKED
QTY/
ORDER CODE
INCL. DRIPTRAY EXCL. DRIPTRAY COUNTER
WEIGHT DIMENSIONS
pgLLET
(D x W x H inches) (D x W x H inches) (T inches)
(L x W x H inches)
•
1000811
OR
•
17.61b
•-
000'
PRODUCT
LU
WATER SIZE
PERFORMANCE SPECS pLUMBING&
pACKAGING
INFO
TYPE
ELECTRICALREQS
•
co
DIMENSIONS
CUPS
PACKAGING
NAME
ADJUST
IMMEDIATE GAV
QTY/EMMM
inches)
/HOUR
(L x W x H
PALLET
inches)
COUNTER CUT-OUT
Front of Font
Boiler Connections to Font
Water
Power Vent
v
6.5"/165mm
VENTILATION REQUIREMENTS
50mm/1.9" clearance required at each side and back of
machine if installed in an enclosed cabinet.
ELECTRICAL INSTALLATION PROCEDURE
When installing the machine, always observe the local
regulations and standards. The appliance is either supplied
with a NEMA L6-20P moulded power cord or a 515P power
cord. A suitable mains power supply socket should be
available within easy access of the appliance so that it can
be disconnected easily after install. The wires from the font
are terminated in a Mini Fit connector which will plug into
a similar Mini Fit connector mounted on the top lid of the
undercounter boiler.
PLUMBING INSTALLATION PROCEDURE
• Ensure that the equipment is installed according to
local plumbing & water regulations.
• Mains water pressure required (limits):14.5-145psi
(100-1000kPa, 0.1-1MPa).
• Requires inline water filter within your water
specifications.
• The machine requires either a 3/8" compression,
or 3/8" John Guest water connection.
• Turn on the water to Flush any impurities, dust etc
from the inlet hose and water pipe. Allow several litres
through. Especially for new installations. Connect the
hose to the inlet valve of the boiler. Make sure a sealing
washer is fitted.
• Turn on water and check for leaks.
• If the overflow vent is plumbed it must be plumbed with
a tundish device.
UBER FONT 1000811
ECOSMART UC10 ECOSMART UC45
1000752US 1000754US
18.5"/470mm
E
18.5"/470mm
E
* Hosing should
O
betrimmed
*Hosing shouldFnZ_p
O
to ensure
be trimmed toE
continuous
ensure continuousE
drop from font 11.6"
drop from fontrn
to boiler /295mm
to boilerN
min 5.1"
/130mm*
E
E
E
E
o
o
Eoo
o
LO
N
N
jn
A
�D
N
m
N
15.5"/395mm
2"/50mm
2"/50mm
E E
E o
O r
0
i4, to
Ui C_
E
• This equipment must be installed with adequate
• backfiow protection to comply with all applicable
• federal, state and local codes.
OPERATING BOILER FORTHE FIRSTTIME
• Check that all installation procedures have been
carried out.
• Ensure water valve is on.
• Plug boiler appropriate electrical supply and press
power button on the front of the machine marked
'Power'.
• The "power on" light will glow green and the machine will
• fill to a safe level, above the elements, before heating.
• The "Ready/Status" light will cycle two red flashes while
the machine is filling to the safe level.
• After this amount of water has heated to about 951C
• the boiler will draw more water in until the temperature
drops by 1 or 2 degrees. The boiler will then heat again.
• This heat fill cycle continues until the boiler is full.
• Whilst the machine is above the safe level and filling,
the "Ready/Status" light will remain blank.
• The "Ready/Status" light will glow green when the
machine is both full and up to normal operating
• temperature.
• The boiler is now ready for use.
• The font is simply activated by pressing the button
on the top of the font.
• NOTE: Because the boiler is electronically controlled no
priming is necessary. The element cannot switch on until
• a safe level of water is reached.
For more information visit www.marcobeveragesystems.com
V c&I
NSF/ANSI4 LISTED