The URL can be used to link to this page

REVIEWED BLD2024-0598+NITRO COFFEE SPECS+5.3.2024_4.42.13_PM+4236966ietapHEM uurfuE On Demonc The Future of Nitro Cold Brew is Here Nitro and Still Dispense The revolutionary technology infuses nitrogen instantly with no volume limitations. Pour as many servings as you like as fast as you possibly can with no deviation in quality. Standalone Dispense System for Cold Brew Coffee A patented technologyfor nitrogenating cold brewcoffee in -line and on -demand was created through years of research and development and a passion for quality dispensing methods. The result is JoeTap. You no longer need to wait several days while your cold brew coffee force- nitrogenates in a keg. Your JoeTap dispenser instantly transforms any cold brew coffee into nitro cold brew at the time of dispense. While the technology is sophisticated, the process is simple — Brew, Tap, Pour. Features Specifications Capacity: 2 x 10 liter corny kegs Product filter monitored and displayed to ensure beverage quality Simple weekly maintenance with reminder and lockout LED lighting inside the refrigerator to increase visibility Dispense tower can be mounted up to ten feet away from the refrigerator 17" (432 mm) 7" (178 mm) / t£ 4 £ 28.5" (724 mm) 11 / 7/8„ (279 mm) (22 mm) 28.0" (711 mm) 15" (381 mm) Dimensions 15" W x 28" H x 28.5" D Tower 17" H Nitro in (A) 1/4" OD John Guest (JG) 12' x 1/4" ID braided tube Nitrogen out 12' x 1/4" OD (JG) Cold brew out 12' x 3/8" ID braided tube (3/8" JG) Note: Nitrogen and cold brew lines bundled (B) in 2 1/2" OD closed cell tube insulation Refrigerant Butane Cord length 8' Approximate net weight 80lbs 2.5" i 1.5" (64 mm) (38 mm) T q -( ). 3.5" min 18" 2.75" min (89 mm) (457 mm) (70 mm) bend radius bend radius MORON MMMMM A ®® B 1" minWEN (25.4 mm) clearance 7" 1" (178 mm) (25.4 mm) JT-NITCOM-R 115 50/60 0.3 IEC C13 NSF-7, JT-NITCOM-L NSF -18, ETL JT-NITCOM-R-220 220 50/60 0.3 IEC C13 JT-N ITCOM-L-220 NSF-7, NSF -18, 2014/30/EU 2014/35/EU JoeTap 855-4JoeTap I info@joetap.com I www.joetap.com 20010, 20011 Rev 22K25 Automatic Bar Controls, Inc. �OeTap nitro Coffee On Dernond Installation and Calibration For Joe Tap Compact Nitro Coffee Dispensing Systems with the following Model Number: JT-NITCOM—(X) JoeTap 2 faucet COMpact NITro Coffee Dispensing System with Remote Dispensing Tower for one Nitrogenated coffee and one Cold brew coffee beverage. (X): L=Left Door Hinge, R = Right Door Hinge 115 V—, 60 Hz, 2.25 A CONTENTS PAGE NUMBER Safety and Warnings / Securite et Avertissements...... 2-3 Installation and System Requirements .......................... 4-9 Calibration and Start -Up .................................................. 10 10- COTUS STE !ATTENTION! JoeTap Cold Brew Coffee Dispensing Systems are NSF certified for the dispensing of Cold Brew Coffee with a pH greater than 5.0, ONLY. SERVICE AND FACTORY ASSISTANCE: Please record your Installer/Service Agent's name and phone number here for future reference: SERIAL NUMBER: SERVICE AGENT NAME: DATE OF INSTALLATION: PHONE: PAGER: Service Assistance: call Wunder -Bar Joe Tap "Toll Free Service Hotline" @ 866-986-3372 anytime, or (707) 448-5151 Monday through Friday, 7:00 AM to 5:00 PM Pacific Time. JT Nitro Installation and Calibration Instructions 032219.pub JFH_L 707.448.5151 ti;c 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 20010, 20011 www.wunderbar.com Automatic Bar Controls, Inc. !ATTENTION! • Read all Instructions before setting up or operating the dispenser. • This dispenser is not to be used by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction. • Always disconnect the main power cord from the electrical source before removing any access panels or attempting to perform any servicing of this dispenser. • The dispenser should never be cleaned using a water jet nor installed in an area where a water jet is used. • Service access panels should be removed by qualified service technicians, ONLY. • Access to the service areas of this dispenser is restricted to qualified technicians with safety/hygiene knowledge, experience, and training for servicing this specific dispenser. • Install and use this dispenser only as described in this instruction manual. Read all Instructions before setting up or operating the dispenser. FCC Statement: This device complies with part 15 of the FCC Rules. Operation of this device is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. IC Statement: This device complies with Industry Canada licence -exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. • Lire toutes les instructions avant d'installer ou d'utiliser le distributeur. • Ce distributeur ne doit pas titre utilise par des personnes (y compris des enfants) ayant des capacites physiques, sensorielles ou mentales reduites ou un manque d'experience ou de connaissances, a moins d'avoir recu une supervision ou des instructions. • Toujours debrancher le cordon d'alimentation de la source electrique avant de retirer les panneaux d'acces ou de tenter d'effectuer toute intervention de ce distributeur. • Le distributeur ne doit jamais titre nettoye avec un jet d'eau, ni installe dans une zone ou un jet d'eau est utilise. • Panneaux d'acces aux services doivent titre enleves par des techniciens qualifies, SEULEMENT. • Acces aux zones de service de ce distributeur est limitee a des techniciens qualifies de la securite / des connaissances d'hygiene, 1'experience et la formation pour 1'entretien de ce distributeur specifique. • Installer et utiliser ce distributeur tel que decrit clans ce manuel d'instruction. Utilisez uniquement du fabricant les accessoires recommandes par. Declaration IC: Cet appareil est conforme aux normes RSS sans licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d'interferences et (2) cet appareil doit accepter toute interference, y compris les interferences pouvant provoquer un fonctionnement non desire de I'appareil. 2 OFFICE 707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. nitro Coffee orra do p I On Demand SAFETY AND ENVIRONMENTAL Q DANGER RISK OF FIRE OR EXPLOSION. FLAMMABLE REFRIGERANT USED. DO NOT USE MECHANI- CAL DEVICES TO DEFROST REFRIGERATOR. DO NOT PUNCTURE REFRIGERANT TUBING. RISQUE D'INCENDIE OU D'EXPLOSION. REFRI- GERANT INFLAMMABLE UTILISE. NE PAS UTI- LISER DE DISPOSITIFS MECANIQUES POUR DE- GIVRER LE REFRIGERATEUR. NE PAS PERCER DE TUBAGE DE REFRIGERANT. A CAUTION RISK OF ELECTRIC SHOCK! IF THE CORD OR PLUG BECOMES DAMAGED, REPLACE ONLY WITH A CORD AND PLUG OF THE SAME TYPE AND RATING. RISQUE DE CHOC ELECTRIQUE! SI LE CORDON OU LA FICHE DEVIENT ENDOMMAGES, NE LE REMPLACEZ QUE PAR UN CORDON ET UNE FICHE DU MEME TYPE ET DE LA QUALITE. RISK OF ELECTRIC SHOCK! DO NOT OPER- ATE THE SYSTEM WITH A DAMAGED POW- ER CORD OR IF THE EQUIPMENT HAS BEEN DAMAGED OR DROPPED —UNTIL IT HAS BEEN EXAMINED BY AN AUTHORIZED SER- VICE PERSON. RISQUE DE CHOC ELECTRIQUE! NE FAITES PAS FONCTIONNER LE SYSTEME AVEC UN CORDON D'ALIMENTATION ENDOMMAGE OU SI L'EQUIPEMENT A ETE ENDOMMAGE OU S'ECHUTE - JUSQU'A CE QU'IL SOIT EX- AMINE PAR UNE PERSONNE DE SERVICE AUTORISEE. QQ DANGER REFRIGERATION COMPONENT PARTS SHALL BE REPLACED WITH LIKE COMPONENTS AND SERVICING MUST BE DONE BY FACTORY AU- THORIZED SERVICE PERSONNEL, ONLY, TO MINIMIZE THE RISK OF POSSIBLE IGNITION DUE TO INCORRECT PARTS OR IMPROPER SERVICE. LES COMPOSANTS DOIVENT ETRE REMPLACES PAR DES COMPOSANTS SIMILAIRES. L'ENTRE- TIEN DOIT ETRE EFFECTUE PAR LE PERSON- NEL D'ENTRETIEN AUTORISE PAR L'USINE UNIQUEMENT POUR MINIMISER LE RISQUE D'ALLUMAGE POSSIBLE EN RAISON DE PIECES INCORRECTES OU D'UN SERVICE INCORRECT. THIS SYSTEM IS INTENDED FOR INDOOR INSTALLATION AND OPERATION ONLY. THIS SYSTEM IS DESIGNED TO OPERATE BETWEEN 50°F (10°C) AND 100°F (38°C). FOR BEST RE- SULTS KEEP UNIT OUT OF DIRECT SUNLIGHT. CE SYSTEME EST CONPU POUR UNE INSTALLA- TION A L'INTERIEUR ET UN FONCTIONNEMENT UNIQUEMENT. CE SYSTEME EST CONPU POUR FONCTIONNER ENTRE 50 ° F (10 ° C) ET 100 ° F (38 ° C). POUR DE MEILLEURS RESULTATS, CONSERVER L'UNITE HORS DU SOLEIL DIRECT. 3 OFFICE:707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 20010, 20011 www.wunderbar.com Automatic Bar Controls, Inc. Anitro Coffee ji 0 P,rap On Demand Installation Instructions These instructions outline the steps involved in installing the JoeTapT1 Refrigeration Unit and Infusion Tower. • Uncrating the JoeTapT1 nitro coffee system • Installing the Refrigeration Unit • Routing the product lines • Installing the JoeTapTM Infusion Tower onto the countertop • Calibration and Start-up procedures Tools & Materials Required: • Product Quality Specification • Number 2 Phillips Screw Driver • Crescent Wrench • Oetiker Clamp crimping Pliers • Tubing Cutter • Electric Drill • 3" Hole Saw • 1 3/8" Hole Saw • 1/4" Drill Bit • Metal Hacksaw • Black or Clear RTV Silicone Sealant • 2.5 Gallon Corny Keg filled with product • 3" ABS Plastic Pipe (Optional -See step 3 in Bar Top Installation Instructions) • Pipe Cutter (Optional -See step 3 in Bar Top Installation Instructions) Items Included with JoeTapTm Refrigeration Unit: Drip Tray Box Contents: • 120 VAC Power Cord • Drip Tray (Includes Drip Tray, Perforated Insert, Washer, and Nut) • 1/4" Barb x 3/8" Stem (John Guest) Fitting with three 12.3 Oetiker clamps • Tower / Drip Tray Mounting Template • 3/8" and 1/4" Locking Clips for John Guest Fittings • Kay 5 Cleaning Solution and Cleaning Y-Tube Assembly • JoeTapTm Tower with Mounting Hardware [Bracket, Gasket, (4)10-24 x 2-1/2" Bolts, (4) Washers, and (4) Nuts] • Tower Tubing Bundle (Black Insulated Bundle) Tower Box Contents: • 2 JoeTapTm Dispenser Tap Handles • Installation, Operation, and Cleaning Instructions Uncrating and Assembly: 1. Remove the banding securing the shipping carton to the pallet. 2. Unpack the Refrigeration Unit. 3. Open the Refrigeration Unit's door and remove the "Tower Box" and the "Drip Tray Box" set them aside. 4. Inspect the "Drip Tray Box" to ensure that all parts listed above in "Items Included with JoeTap Refrigeration Unit" are present and undamaged. Inspect the Tower to confirm that both faucets are present and not damaged. 4 OFFice 707.448.5151 FAx. 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. A nitro Coffee JO P,T8P I On Demand Assembling and Installing the Refrigeration Unit: 1. Remove the Refrigeration Unit from its packaging. 2. Connect Power Cord to the Socket located in the center of the bottom rear of the Refrigeration Unit. 3. Roll the refrigerator to its preferred location. NOTE: The following minimum clearances are required! Detail A —Product lines to tower = Minimum 3.05" (77.5mm) Detail B—Nitrogen Line = Minimum 2.06" (52.3mm) Rear of Refrigerator Clearance = Minimum 1.0" (25.4mm) Q nrl 1) ncz Front Grill Must Is I remain free of obstruction for refrigerator cooling. W 1 2. Rout the product line bundle to the location where the bar top dispense tower will be installed. 3. Rout the nitrogen line to the nitrogen source. 4. Plug the refrigerator into 115VAC NEMA 5-15 receptacle and roll it into place. 5 OFFICE 707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. nitro Coffee d 0 'rTa P I On Demand Installation Instructions (continued) Bar Top Tower Installation: Use the JoeTapTM laminated mounting template included with each JoeTapTm dispensing system to mark and drill the mounting holes for the JoeTapTM Infusion Tower (Y diameter), Tower Mounting Bolts (4 X 1/4" diameter) and drain pan Drain (1-3/8" diameter) (see Figure 1). (REAR) Bracket Tower O p\ Drill hole 03.00 4x Drill holes 0.25 Drill hole 01.375 Drain JoeTap Template P/N JT-12702 (FRONT) 2. Place the included Tower Gasket on the counter top, aligned with the four'/4" Bolt holes in the countertop. Place the JoeTap Infusion Tower over the Gasket, with the four mounting holes in the Tower Gasket, JoeTapTM Infusion Tower, and the counter top aligned. 3. NOTE: If the countertop is made of laminated wood, place a 3" OD piece of plastic pipe, cut to the same length as the countertop's finished (laminated) thickness, into the 3" hole that was cut for the Tower tubing to pass through. 4. Install, two each, of the provided 10-24 x 2 1/2" Bolts, Nuts, and Washers into the front right and back left holes. 5. Route the black insulated Tubing Bundle to the underside of the JoeTapTM Infusion Tower. Cut the tubing to proper length. Note: Ensure tubing end cuts are at 90 degrees to ensure a proper seal in the tower fittings) Allow three extra feet of insulated tubing length to insure you can pull refrigerator forward for cleaning. 6. Measure and cut the clear braided tubing and the white tubing so that the two tubes can plug into the tower without causing unnecessary bends. A. Insert the '/4" barbed end of the gray Barb -Stem Union Fitting, provided, into the end of the Clear Braided Tubing (protruding from the end of the Tubing Bundle). Do not install the Clamp yet! (See Figure 2, page 5) Push the stem end of the same fitting into the 2-Way Divider fitting that protrudes from the bottom of the JoeTapTM Infusion Tower. Make sure the gray Stem is fully inserted into the 2-Way Divider's Inlet. B. Insert the end of the White Tube into the Check Valve located at the bottom of JoeTap Infusion Tower to check if attaching it causes any bends in the Clear Braided tubing; if there are unnecessary bends, cut the white tube again to proper length. C. Remove the tubes from the tower to install the Tower Bracket. OFFIce707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. , A eira dO P Installation Instructions (continued) Bar Top Tower Installation: Initro Coffee On Demand Figure 2 Two -Way Divider Fitting Inlet N%, _Check Valve Gray stem end of Barb -Stem Union Barbed End of the Barb - Stem Union Installed - into the Braided Tubing Clear Braided White LLDPE � Tubing Tubing 7. Once the tubes are cut to proper lengths push them through the two Strain Relief (Cord Grips) installed into the Tower Bracket (Figure 3). The Small Strain Relief, with the light gray rubber sleeve insert, is for the White LLDPE Tubing. The Large Strain Relief, with the bigger hole and no Sleeve, is for the Clear Braided Tubing with installed Barb -Stem Union Fitting. A. Insert the Clear Braided Tubing so that the threaded portion on the cord grip attached to Tower Bracket is facing away from the insulation on the Tubing Bundle (see Figure 3). B. After both Tubes are pushed through the Strain Releifs, install the provided Clamp over the Barb -Stem Union and onto the end of the Clear Braided Tubing and the secure the Oetiker Clamp with a crimping pliers. Gray Stem end Barb -Stem Unii 12.3 Oetiker Clam Large Strain Re - Cie gure 3 Fower Bracket E Small Strain Re- 7 OFFICE 707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. nitro Coffee Fra dO P I On Demand Installation Instructions (continued) Bar Top Tower Installation: Two -Way Divider Fitting Inlet 3/8" Red Locking Clip Clear Braided Tubing Large Strain Relief Knob Figure 4 Check Valve 1/4" Red Locking Clip White LLDPE Tubing Small Strain Relief Knob Insert the stem end of the Barb Stem Union Fitting, attached to the Clear Braided Tubing, into the 2-Way Divider fitting located at the bottom of the JoeTapTM Infusion Tower. Make sure the stem is fully inserted into the 2-Way Divider's inlet (see Figure 4). Insert the White LLDPE Tubing into the Check Valve at bottom of JoeTapTM Infusion Tower making sure the tube is fully inserted in the Check Valve. Insert the provided 3/8" Red Locking Clip into the 2-Way Divider's Lock -Ring where the Barb Stem Union Fitting attached to Clear Braided Tubing was inserted (see Figure 4). 10. Insert the provided '/4" Red Locking Clip into the Check Valve's Lock -Ring where the White LLDPE Tubing was inserted (see Figure 4). 11. Position the Tower Bracket so the Bracket's two mounting holes are align with the remaining two holes in the countertop. Install the two remaining, provided, 10-24x2 1/2" Bolts, Nuts, and Washers through the remaining mounting holes located in the JoeTapTM Infusion Tower, countertop, and Tower Bracket (as shown in Figure 4). After tightening all four Mounting Nuts, use a hack saw to cut the remaining exposed bolt to 2-1/2 threads or less. 12. Tighten the Knobs on both the Strain Reliefs attached to the Tower Bracket so the Strain Reliefs grasp the hoses routed through them. Lightly pull on the hoses to make sure the tubes have been properly anchored, if either moves freely, tighten the knob on that strain relief more to increase the gripping strength. OFFice707.448.5151 1 FAX: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. nitro Coffee Fra do P On Demand Installation Instructions (continued) Bar Top Tower Installation: Figure 5 13. Install the provided Tap Handles onto the two faucets included with the JoeTapTM Infusion Tower (see Figure 5). Bar Top Drain Installation: Insert the Drip Tray's threaded Tailpiece through the 1 3/8" hole made using the Tower Mounting Template during the Bar Top Tower Installation step 1 on page 4 of this manual (see Figure 6). Install the provided 1-1/4" Washer onto the Drip Tray's threaded Tailpiece from under the countertop (as shown in Figure 7). Install the provided Hex Nut onto the Drip Tray's threaded Tailpiece. Adjust the orientation of the Drip Tray so the two faucets on the JoeTapTM Infusion Tower are positioned directly over the centers of the two holes located in the drip tray Insert. Once the faucets are aligned, apply a small bead of black or clear RTV silicone sealant around the entire perimeter of the Drip Tray's bottom edge (rim). I F OFFICE:707.448.5151 1 FAx: 707.448.1521 20YOVisw pM,S1uite 100, Vacaville, CA 95688 www.wunderbar.com Automatic Bar Controls, Inc. A nitro Coffee d, OeiraP I On Demand Calibration and Start -Up Instructions System Calibration 1. Once the tower is installed: 2. Connect the ID tubing to the nitrogen generator or nitrogen tank. Fitting and nitrogen sup- ply provided by others. 3. Turn on the nitrogen generator or open the nitrogen tank valve and wait for it to build to oper- ating pressure. 4. Once the generator has achieved full pressure, adjust the pre -filter nitrogen regulator to 40psi. Assure the faucets are closed.. 5. Connect the black Product (ball lock) Connector to the Product Tank fitting that is labeled "OUT" by pulling the black Connector's flanged Lock Ring upward fully while pushing the black Connector onto the product tank fitting labeled "OUT" fully and then release the black Connector's lock ring. Pull up on the black Connector to confirm that it is securely latched onto the "OUT" tank connection. 6. Connect the gray Gas (Ball Lock) Connector to the Product Tank fitting that is labeled "IN" by pulling the gray Connector's flanged Lock Ring upward fully while pushing the gray Connector onto the product tank fitting labeled "IN" fully and then release the gray Connector's lock ring. Pull up on the gray Connector to confirm that it is securely latched onto the "IN" tank System Start - Pull the secondary regulator's black knob (labelled "Nitrogen Out") Upward until a slight click is felt, indicating that the regulator is in adjustment mode. Set the pressure to 9psi using the Nitrogen Pressure readout on the touchscreen. Increase the pressure by turning the knob clockwise. Decrease the pressure by turning the knob counterclockwise. 2. Place a 16oz clear plastic "cold beverage" cup under the nitro faucet. Open nitro faucet until product starts pouring. Close the faucet. 3. Place a serving cup under the nitro faucet and pour a full product serving into the cup. Ob- serve the cascade and head size. Use the Product Quality Specification to determine product acceptability. 4. If there is less/more nitro effect than desired, adjust the black knob on the regulator labelled "Nitrogen Pre -Filter" to increase or decrease the nitro effect. Increasing pressure will increase the cascading and foam height. 5. Continue adjusting and pouring until the level of nitro meets your requirements. Once you have found the desired level of nitrogenation, push the black knob in to lock it in place. Ad- justments can be made at any time. 10 OFFICE 707.448.5151 1 FAx 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. AanitroCoffee�eTap On Demand Operators Guide For Joe Tap Compact Nitro Coffee Dispensing Systems with the following Model Number: JT-NITCOM-(X) JoeTap 2 faucet COMpact NITro Coffee Dispensing System with Remote Dispensing Tower for one Nitrogenated coffee and one Cold brew coffee beverage. (X): L=Left Door Hinge, R = Right Door Hinge 115 V—, 60 Hz, 2.25 A PAGE CONTENTS NUMBER Cleaning & Maintenance -Daily Filter Cleaning ............. 2-7 Cleaning & Maintenance -Daily Tap & Font Cleaning... 8-10 Cleaning & Maintenance -Weekly System Cleaning..... 11-17 Troubleshooting............................................................... 18-19 10 COTUS STE !ATTENTION! JoeTap Cold Brew Coffee Dispensing Systems are NSF certified for the dispensing of Cold Brew Coffee with a pH greater than 5.0, ONLY. Service Assistance: call Wunder -Bar Joe Tap "Toll Free Service Hotline" @ 866-986-3372 anytime, or (707) 448-5151 Monday through Friday, 7:00 AM to 5:00 PM Pacific Time. JT Nitro Operators Guide 030819.pub OFFICE:707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 20010, 20011 www.wunderbar.com Automatic Bar Controls, Inc. AoeTap Cleaning and Maintenance nitro Coffee On Demand The Joe Tap system is equipped with a filter and faucets that will require cleaning one or more times per day (see below). In addition, the entire system must be cleaned once weekly to ensure optimal system performance (page 18, Weekly Cleaning). Daily Filter Cleaning The JoeTap system is equipped with a filter installed in the output line leading from the keg. This filter must be re- moved and cleaned daily to ensure optimal system performance. The unit is equipped with a timer that will alert the user that the daily filter cleaning is due. To start the filter cleaning procedure, select "Cleaning" (Figure 8) on the touchscreen and then select "Filter Cleaning" (Figure 9). 10 OFFICE:707.448.5151 1 FAx 707.448.1521 20602Cessna Drive 0010, 2061 Suite 100, Vacaville, CA 95688 www.wunderbar.com OI n [ Filter Cleaning Filter Cleaning is to be performed daily & will take approximately 30 min to complete Do you want to begin Filter cleaning walkthrough? © No Start 4 Filter Cleaning Figure 11 1 Disconnect PRODUCT KEG © Cancel Filter Cleaning 1 Store PRODUCT KEGS in back of house fridge Next Figure 12 Back Next :u Filter Cleaning 1 Wash hands before proceeding Back Filter Cleaning 1 Shut off BLUE VALVE located in front of the filter 2 Open NITRO TAP to release pressure Back Filter Cleaning 1 Shut off BLUE VALVE located behind the filter 2 Close NITRO TAP Figure 13 Next 4 Figure 14 Next 4 Figure 15 Back Next 4 jLjtdp I c Filter Cleaning 1 With towel remove filter cap by turning counter clockwise • (keep as vertical as possible to reduce spillage) <- Back Filter Cleaning 1 Clean FILTER and FILTER CAP • (keep as vertical as possible to reduce spillage) <- Back Filter Cleaning 1 Check FILTER & FILTER CAP for O-RINGS • Replace O-RING(S) if they have come loose or detached Figure 16 Next 4 Figure 17 Next 4 Figure 18 Back --IN IV Next 4 1iuru Filter Cleaning 1 Insert FILTER back into housing 2 Replace FILTER CAP by turning clockwise <— Back Figure 19 Next 4 Filter Cleaning Figure 20 1 Turn BLUE VALVE behind the filter to ON position 2 Turn BLUE VALVE iii��i/ -- 2 in front of the filter to ON position <— Back Filter Cleaning 1 Clean interior of refrigerator 2 Wipe KEG CONNECTORS with SANITIZER CLOTH Next 4 Figure 21 Back Next 4 Automatic Bar Controls, Inc. Daily Filter Cleaning (Continued) oeirap nitro Coffee On Demand 15 OFFICE:707.448.5151 1 FAx: 707.448.1521 2060 �Uw,riYo&gtg 100, Vacaville, CA 95688 www.wunderbar.com Automatic Bar Controls, Inc. Anitm Coffee Daily CleaningFont"lio OTFOP On Demand "Tap The JoeTap system requires daily cleaning of the dispense taps and drain area. The system is equipped with a timer that will alert the user that the daily tap and font cleaning is required. To start the tap and font cleaning procedure, select "Cleaning" (Figure 23) on the touchscreen and then select "Tap & Font Cleaning" (Figure 24). 16 `FFI F 707.448.5151 1 FAx 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 ve�ap I O� o Tap & Font Cleaning 1 Remove DRAIN GRATE 2 Clean & Sanitize DRAIN GRATE • Use 3-Compartment sink method or dish machine © Cancel Tap & Font Cleaning 1 Remove TAP NOZZLES by unscrewing them <- Back Tap & Font Cleaning 1 Clean any debris with FOOD -CONTACT detail brush 2 Flush with water & wipe dry T Next 4 Figure 27 rif Next 4 Figure 28 Back W� Next 4 I Automatic Bar Controls, Inc. J1 oeTap Daily Cleaning "Tap & Font" (Continued) Initro Coffee On Demand 18 OFFICE:707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. A nitro Coffee ROW 0 P,T8 P On Demand Weekly Cleaning The JoeTap system is equipped with a timer that will alert the user that the weekly cleaning is required. The system will be disabled if the weekly cleaning procedure is not performed. To ensure optimal system performance, perform the following cleaning procedure once a week. To start the weekly cleaning procedure, select "Cleaning" on the touchscreen (see Figure 31) and then select "Beverage Line Cleaning" (see Figure 32). PREPARATION FOR WEEKLY CLEANING CLEANING SOLUTION: Use a Sanitizing Solution capable of providing 100 PPM of available chlorine when properly mixed with warm (approximately 100°F /38°C) water such as KAY 5® chlorinating sanitzer available from Kay Chemicals in 1 ounce packets. Or, use other Sanitizing Solutions that provide 100 PPM available chlorine solution when mixed per the man- ufacturer's instructions, with 100°F /38°C potable water. CLEANING SOLUTION PREPARATION: KAY 5®: Mix One, 1 ounce packet of Kay 50 sanitizer powder with 2-1/2 gallons / 9-1/2 liters of 100°F / 38°C water in a clean product tank. Other Sanitizing Solutions: Mix the recommended amount of sanitizing solution or powder (per instructions) with 2-1/2 gallons of 100°F / 38°C water to achieve a 100 PPM concentration of available Chlorine, in a clean product tank. Install the product tank lid before attaching to the system. 19 OFFICE 707.448.5151 1 FAx. 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 jetap I c Beverage Line Cleaning Figure 33 Beverage Line Cleaning is to be performed weekly & will take approximately 30 min to complete Once started, this cleaning cycle cannot be stopped © Cancel Start 4 Beverage Line Cleaning Figure 34 1 Gather all cleaning supplies 2 Prepare CLEANING KEG • Using a markout pitcher, fill a clean sanitized keg with 2.5 gallons of warm water and 1 packet of KAY-5 cleaner • Label CLEANING KEG with DAY DOT "WASH" Beverage Line Cleaning 1 Disonnected PRODUCT KEG A. Detach (GREY) GAS LINE) first (grey cap attached to "in port") B. Detach (BLACK) BEVERAGE LINE second (black cap attached to 'but port") Next 4 Figure 35 Next 4 illut jUtup I nn r Beverage Line Cleaning Figure 36 1 Store PRODUCT KEGS in back of house fridge Next Beverage Line Cleaning Figure 37 1 Attach CLEANING KEG A. Attach (GREY) GAS LINE first (grey cap attached to "in port") B. Attach (BLACK) BEVERAGE LINE second (black cap attached to 'but port") Next Beverage Line Cleaning Figure 38 1 Connect TAP LINE CLEANING TUBES to TAP NOZZLE & place tube into drain tray �i Next JUUdIJ I ' Beverage Line Cleaning Figure 39 1 Open both TAPS 2 Set timer for 10 minutes • Cleaning cycle will take aprox. 10 min • Complete other tasks while cleaning cycle is in progress Beverage Line Cleaning Purging & Priming Product (Keep Taps Open) 12 oz remaining Beverage Line Cleaning Soaking Cleaning Solution (Keep Taps Open) 4:55 left Next 4 Figure 40 Figure 41 Uetap • d, On Di • Beverage Line Cleaning Figure 42 Purging & Priming Product (Keep Taps Open) 0 oz remaining - '} Beverage Line Cleaning Figure 43 1 Close both TAPS Next Beverage Line Cleaning Figure 44 1 Disconnect & remove CLEANING KEG from equipment A. Detach (GREY) GAS LINE first (grey cap attached to "in port") B. Detach (BLACK) BEVERAGE LINE second (black cap attached to "out port") Next JetdPO � n 0 Beverage line Cleaning 1 Attach PRODUCT KEG to nitro unit A. Attach (GREY) GAS LINE second (grey cap attached to "in port") B. Attach (BLACK) BEVERAGE LINE first (black cap attached to 'but port") Beverage Line Cleaning 1 Open both TAPS Beverage Line Cleaning Purging & Priming Product (Keep Taps Open) 13 oz remaining e- Figure 45 Next 4 Figure 46 Next Figure 47 Automatic Bar Controls, Inc. Weekly Cleaning (Continued) ,joeTap Initfo Coffee On Demand 25 OFFicE:707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. Troubleshooting d, oeTap nitro Coffee On Demond MACHINE SYMPTOM WHAT TO DO Make sure the power cord is plugged into the wall receptacle Display is blank Make sure wall receptacle has power Unplug the power cord for 5 minutes and plug it back in. Select "Machine Info" — Look for pressure readings that are out of the nominal range. Nominal Display Readings Pressure Name Nominal Range Pre -Filter PSI: 38-42 PSI Post -Filter PSI: 36-42 PSI Nitrogen PSI: 7-10 PSI 26 OFFICE:707.448.5151 1 FAx: 707.448.1521 2060 Cessna Drive, Suite 100, Vacaville, CA 95688 www.wunderbar.com 20010, 20011 Automatic Bar Controls, Inc. Troubleshooting (continued) nitro Coffee On Demand DISPLAYED MESSAGE WHAT TO DO LOCKOUT Run the weekly cleaning cycle LOW PRESSURE Make sure the coffee keg is connected Clean the filter CLEANING DUE Run the weekly cleaning cycle soon MACHINE SYMPTOM WHAT TO DO Check for empty coffee keg in the refrigeration unit NO PRODUCT FLOW Make sure the coffee keg is connected Clean the filter Run the weekly cleaning cycle NITRO COFFEE IS FOAMY Check for nominal Pressure Readings Check for nominal Pressure Readings NITRO COFFEE IS FLAT Run the weekly cleaning cycle Clean the filter DISPENSE RATE IS SLOW Run the weekly cleaning cycle 27 OFFICE: 707.448.5151 1 FAx: 707.448.1521 20,G Ll64WJbb1 Suite 100, Vacaville, CA 95688 www.wunderbar.com VM0183 &N �NT.Vtamix. Multi -Use Rinse and Wash Station The Spraypark is the more efficient way to rinse *blending pitchers, tea shakers, and steaming pitchers. Just place the pitcher upside down, engage the automatic start, and watch as the water pressure rinses residue away, saving time and money. Smart Product Design • Automatic start and shut off for hands -free rinsing • Pre-program rinse cycle provides efficiency • In sink mounted design eliminates need for above -counter hose and faucet connection • Multi -purpose rinsing for pitchers, shakers, steaming pitchers, and milk pitchers *64 oz. containers or smaller for most manufacturers 17564 VM0183 CT ritamix. Product Specifications Vitamix° Spraypark Item Number: 61304 Starbucks SKU: 011075242 Electrical: 120V, 220-240V,100V, 50/60 Hz Pack: Includes 1 rinse tower with shut off valve, power supply, Plumbing In Box, and instructions. Plumbing In Box includes the following: Pressure reducing valve, solenoid, strainer, dual check valve, backflow preventer, hose assembly/connectors, external shut off, and electronics. Net Weight: 15 lbs. FOR COMMERCIAL USE ONLY NSF. c&S 12 .500 .356 5.747 AUTO WA� a /%r 00 .470 COR stores needs to submit a work task for replacements and repairs. LS stores needs Replacement Parts to reach out to ICEE - dispatchsupervisor@icee.com or call 1-800-423-3872 and ask for dispatch supervisor. ia 0 Item Number: 063246 Item Number: 063247 Starbucks SKU: 011075247 Starbucks SKU: 011075246 Pack: Includes 1 Tower Assembly Pack: Includes 1 Nozzle OO Oo Item Number: 063251 Item Number: 063252 Starbucks SKU: 011075245 Starbucks SKU: 011075244 Pack: Includes 1 Shuttle Assembly 4) Pack: Includes 1 Spray Cage 17564 ©2017 Vita -Mix" Corporation 3/17 2 of 3 VM0183 &'vitamix. Plumbing Layout ITEM DESCRIPTION CITY 1 SS BRAIDED HOSE /3/8"COMP -3/8"COMP /12'LNG 3 2 ADAPTER / 3/8" COMP -1/2" M NPT / BRASS 2 3 SHUT OFF VALVE 1 4 NIPPLE / HEX / BRASS / 1/2" M NPT / WITH THREAD SEALER 1 5 STRAINER / WYE / 100 MESH / CLEANOUT 1 6 ELBOW / 3/8" COMPRESSION - F GHT / BRASS 3 7 ADAPTER / 1/2" M NPT - M GHT / BRASS 3 8 PRESSURE REDUCING VALVE / 1/2" F NPT 1 9 STEM ADAPTOR / PUSH FIT / 1/2" STEM -1/2" M NPT 1 10 TEE / PUSH FIT / 1/2' TUBE 2 11 TUBE /LLDPE/1/2"OD X 3.75"OAL 2 12 STEM ELBOW / 1/2" STEM -1/2' TUBE 2 13 SHUT OFF VALVE / PUSH FIT / 1/2" TUBE 1 14 STEM ADAPTOR / PUSH FIT / 1/2' TUBE - 3/8" M NPT 1 15 SOLENOID /24 VDC/3/8"FNPT 1 16 ELBOW / SWIVEL / 1/2" TUBE - 3/8" M NPT 1 17 TUBE / LLDPE / 1/2" OD X 1.9" OAL 1 18 ELBOW / PUSH FIT / 1/2' TUBE - 1/2' TUBE 1 19 TUBE / LLDPE / 1/2' OD X 2.25" OAL 1 20 TUBE /LLDPE/1/2"ODX4.2 CAL 1 21 ADAPTOR / STRAIGHT / PUSH FIT / 1/2' TUBE -1/2" M NPT 1 22 DUAL CHECK VALVE / 1/2" F NPT 1 23 TOWER/AUTO RINSER 1 24 NOZZLE / ONE PIECE 1 25 SHUTTLE BODY ASY 1 26 SHUTTLE HEAD 1 27 RETAINER NUT ASSEMBLY/ SPRAYPARK TOWER 1 28 LID ASY /PIB/BARE 1 29 BOTTOM ASY / PIB /BARE 1 30 NOZZLE ASY / MANUAL 1 31 POWER SUPPLY / RINSER /SPRAYPARK 1 *Power supply cord length 6 feet, 4 feet usable R 30 13 12 12 I6 I, 8 O O 9 B 10 9 0o IO O 20 G 21 6 dQ 7 ^ 17564 ©2017 Vita -Mix" Corporation 3/17 3 of 3 _ 21679 - LOW VOLTAGE The NG3000 series nitrogen generator is designed to meet the demands of keg based nitro cold brew dispensing systems, while minimizing required floor space PRODUCT INFORMATION NZ Purity Up to 99.8% Output Pressure Up to 125 psi Noise Level <_ 60 dB(A) Environment Clean, dust free, well ventilated Normal Ambient 4-40°C / 39-104°F Safety Certificates NSF and cULus certified Weieht Amp hp kW Ibs kg Volts Freq. 2.8 1/4 0.19 65 29 120 60 POWER SWITCH PRESSURE GAUGE / NITROGEN OUTPUT O® ® 23.98 [W9.0] I 16.08 [408.4] 7.18 [182.3] 21679 - HIGH VOLTAGE The NG3000 series nitrogen generator is designed to meet the demands of keg based nitro cold brew dispensing systems, while r minimizing required floor space PRODUCT INFORMATION NZ Purity Up to 99.8% Output Pressure Up to 125 psi Noise Level <_ 60 dB(A) Environment Clean, dust free, well ventilated Normal Ambient 4-40°C / 39-104°F Power Cords Plug Types F,G,I,M available Safety Certificates NSF certified, CE approval pending Weieht Amp hp kW Ibs kg Volts Freq. 2.8 1/4 0.19 65 29 230 50 POWER SWITCH PRESSURE GAUGE / d NITROGEN OUTPUT O® ® 23.98 [609.0] 1 16.08 [408.4] if 7.18 [182.3] DETAIL SHEET SHEET I OF 2 9/1/2021 86R-3MNI-DSSLH 230V N2 SYSTEM 1993011 DATE DESCRIPTION PART NUMBER NOTES: 1 TEST SPECIFICATIONS HY-POT: A LOW VOLT START TEST: 198V, 50Hz CUT OUT PRESSURE: 118-132 PSI CUT IN PRESSURE: 98-112 PSI PRESSURE RELIEF VALVE SETTING: N/A TIMER ON TIME SETTING: N/A AMP DRAW AT 230V/50Hz: <=2.3 AMPS ON TIME TO CHARGE: <=184 SECONDS FUNCTIONAL TEST N2 PURITY LEVEL: >=92.00/o 2 PRINT DATA LABEL (CE, NSF, UKCA): ITEM NO: 1993011 DESC: 86R-3MNI-DSSLH VOLT: 220-240/50-60Hz CURRENT: 2.1A/1.5A TEMP: 4/40'C PS: 125 PSI MAX 3 SCFH (42% DUTY CYCLE) (110 SEC. ON /150 SEC. OFF) R REVISION: P 00 0,70 READ O&M • MANUAL LABEL 03 o ® DISCONNICT POWER LABEL ® ELECTRIC SHOCK ® WARNING LABEL GROUND LABEL—� CAL TI ON —,-0 LABEL —/El ® DATA LABEL N S ]F. The Public Health and Safety Organization NSF Product and Service Listings These NSF Official Listings are current as of Wednesday, October 13, 2o2i at 12:15 a.m. Eastern Time. Please contact NSF to confirm the status of any Listing, report errors, or make suggestions. Alert: NSF is concerned about fraudulent downloading and manipulation of website text. Always confirm this information by clicking on the below link for the most accurate information: http_//info.nsf.org/Certified/foodIListings.asp?Company=Co3o4853& NSF/ANSI 18 Manual Food and Beverage Dispensing Equipment Gast Mfg. Inc. 23oo Highway M-139 Benton Harbor, MI 49023 United States 269-927-5743 Facility: Benton Harbor, MI COMPONENTS: DETAIL SHEET SHEET 1 OF 2 1 6/10/2021 1 86R-3MNI-DSBHH 120/60 N2 SYSTEM 1 1993010 1 DATE I DESCRIPTION I PART NUMBER NOTES: 1 TEST SPECIFICATIONS HY-POT: A LOW VOLT START TEST: 103V, 60Hz CUT OUT PRESSURE: 118-132 PSI CUT IN PRESSURE: 98-112 PSI PRESSURE RELIEF VALVE SETTING: N/A TIMER ON TIME SETTI NG: N/A PEAK AMP DRAW AT 115V: <=3.0 AMPS ON TIME TO CHARGE: <=165 SECONDS FUNCTIONAL TEST N2 PURITY LEVEL: >=92.00/o 2 PRINT MODEL LABEL: (cULus, NSF) ITEM:1993010 DESC: 86R-3MNI-DSBHH VOLT: 120V/6OHz CURRENT: 2.9A TEMP: 4/40'C PS: 125 PSI Max 3 SCFH (37% DUTY CYCLE) (90 sec. ON/150 sec. OFF) R REVISION: L 00 0,70 READ O&M • MANUAL LABEL 03 o ® DISCONNI!CT POWER LABEL ® ELECTRIC SHOCK ® WARNING LABEL GROUND LABEL—� CALM ON �0 LABEL DATA LABEL CERTIFICATE OF COMPLIANCE Certificate Number 20190718-E186511 Report Reference E 186511-20190708 Issue Date 2019-JULY-18 Issued to: JUN-AIR USA INC 2300 M139, PO BOX 97 BENTON HARBOR MI 49022 This certificate confirms that COMPRESSORS, VACUUM PUMPS AND PNEUMATIC representative samples of PAINT SPRAYERS USL, CNL - Tank Type Compressor, Model 86R-3MN1- DXXXX Have been investigated by UL in accordance with the component requirements in the Standard(s) indicated on this Certificate. UL Recognized components are incomplete in certain constructional features or restricted in performance capabilities and are intended for installation in complete equipment submitted for investigation to UL LLC. Standard(s) for safety: UL1450 - Motor Operated Air Compressors, Vacuum Pumps, and Painting Equipment CAN/CSA C22.2 No. 68 - Motor Operated Appliances (Household and Commercial) Additional Information: See the UL Online Certifications Directory at https://ig.uIprospector.com for additional information. This Certificate of Compliance does not provide authorization to apply the UL Recognized Component Mark. Only the UL Follow -Up Services Procedure provides authorization to apply the UL Mark. Only those products bearing the UL Recognized Component Mark should be considered as being UL Certified and covered under UL's Follow -Up Services. Look for the UL Recognized Component Mark on the product. Bruce Mahrenholz, Director North American Certification Program UL LLC Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, please contact a local UL Customer Service Representative at http://ul.com/aboutul/locations/ Page 1 of 1 NSF International 789 N. Dixboro Road, Ann Arbor, MI 48105 USA RECOGNIZES Gast Mfg. Inc. Benton Harbor. MI AS COMPLYING WITH NSF/ANSI 18 AND ALL APPLICABLE REQUIREMENTS. PRODUCTS APPEARING IN THE NSF OFFICIAL LISTING ARE AUTHORIZED TO BEAR THE NSF MARK. This renifim&istM1e pm eFNSF International and mmbe mtumN upnn rtqunL MS mtificue manums valid as long as this clieathasproMats in Listing fortM1e relermcetl emndmde. Fnr IM1e moat cnrtml mdwmplete Luling in(omstion,pinse azeess N$F's website (www.nyf og). 16-E September 15, 2016 Sarah Ktol Certificareb C0304853 - 01 Global Managing Director, Food Sakty &odwt Certification Element 7 Nitrogen Gas Generator[i] LOA-(1)(2)04050)(7)(8) [1] (1) Receiver Size: 0 - No tank 0.4 - 0.4 liter tank 1.5 - 1.5 liter tank 4 - 4 liter tank 15 - 15 liter tank 25 - 25 liter tank (2) Enclosure Type: M - Metal Cover (3) Separator Type: N1 - Nitrogen Separator (CMS) N2 - Nitrogen Separator (Membrane) (4) Compressor Configuration: A - Single Cylinder, Low Stroke B - Single Cylinder, High Stroke (0.35") C - Single Cylinder, High Stroke (0.42") Bent Valve (100psi max) G - Dual Parallel Cylinder, Low Stroke H - Dual Parallel Cylinder, High Stroke (0.37") J - Dual Parallel Cylinder, High Stroke (0.42") Bent Valves N - Dual Staged Cylinders, Std Stroke P - Dual Independent Cylinders, Std Stroke S - Special compressor configuration (5) Accessory Configuration: A - Manual tank drain, 5µ F/R manual drain, no bottle, pressure switch unloader B - Manual tank drain, 5µ F/R auto drain, with bottle C - Manual tank drain, 5µ F/R manual drain, 0.01µ Coalescing Filter, no bottle D - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, with bottle E - Manual tank drain, 5µ F/R auto drain, no bottle, pressure switch unloader F - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, no bottle K - Auto tank drain, 5µ F/R auto drain, with bottle L - Auto tank drain, 5µ F/R auto drain, 0.01µ Coalescing filter, with bottle M - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, no bottle N - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, with bottle R - Integrated IOT S - OEM Specific Model (6) Elec/Region Config: A - 100/50 or 60 Japan (NEMA 1-15 or 5-15) B - 120/50 or 60 NA (NEMA 5-15) C - 220-240 50 or 60 NA (NEMA 6-15) D - 220-240 50 or 60 EU (CEE 7/7) E - 220-240 50 or 60 EU (CEE 7/7) & GB adaptor F - 220-240 50 or 60 CH (NEMA 1-15 or AS-3112) G - 220-240 50 or 60 AU (AS-3112) H - 220-240 50 or 60 GB (IEC Type G) S - Special voltage/plug (7) System Regulatory: A - CE B - CSA C - cULus D - CE/cULus E - CCC F - cCSAus G - cULus/NSF H - None S - Special (8) Tank Regulatory: A - CE B - ASME C - ASME Singapore D - GB (china) E - CRN F - ASME/CE G - ASME/CRN H - CE/UL S - Special Nitrogen Gas Generator for Beverage Systems[2] 8 6 R-(1)(2)(3)-(4)(5)(6)(7)(8) 87R-(1)(2)(3)44)(5)(6)(7)(8) [2] (1) Receiver Size: 0 - No Tank 1.5 - 1.5 liter tank 3 - 3 liter tank 4 - 4 liter tank 15 - 15 liter tank (2) Enclosure Type: M - Metal Cover (3) Separator Type: N1 - Nitrogen Separator (CMS) N2 - Nitrogen Separator (Membrane) NB - Nitrogen Separator (CMS), CO2 Blender (4) Compressor Configuration: A - Single Cylinder, Low Stroke B - Single Cylinder, High Stroke (0.35") C - Single Cylinder, High Stroke (0.42") Bent Valve (100psi max) D - Single Cylinder, High Stroke (0.45") Bent Valve G - Dual Parallel Cylinder, Low Stroke H - Dual Parallel Cylinder, High Stroke (0.37") J - Dual Parallel Cylinder, High Stroke (0.42") Bent Valves N - Dual Staged Cylinders, Std Stroke P - Dual Independent Cylinders, Std Stroke S - Special compressor configuration (5) Accessory Configuration: A - Manual tank drain, 5µ F/R manual drain, no bottle, pressure switch unloader B - Manual tank drain, 5µ F/R auto drain, with bottle C - Manual tank drain, 5µ F/R manual drain, 0.01µ Coalescing Filter, no bottle D - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, with bottle E - Manual tank drain, 5µ F/R auto drain, no bottle, pressure switch unloader F - Manual tank drain, 5µ F/R auto drain, 0.01µ Coalescing Filter, no bottle K - Auto tank drain, 5µ F/R auto drain, with bottle L - Auto tank drain, 5µ F/R auto drain, 0.01µ Coalescing filter, with bottle M - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, no bottle N - Auto tank drain, 5µ Filter auto drain, regulator, solenoid unloader, with bottle S - OEM Specific Model (6) Elec/Region Config: A - 100/50 or 60 Japan (NEMA 1-15 or 5-15?) B - 120/50 or 60 NA (NEMA 5-15) C - 220-240 50 or 60 NA (NEMA 6-15) D - 220-240 50 or 60 EU (CEE 7/7) E - 220-240 50 or 60 EU (CEE 7/7) & GB adaptor F - 220-240 50 or 60 CH (NEMA 1-15 or AS-3112) G - 220-240 50 or 60 AU (AS-3112) H - 220-240 50 or 60 GB (IEC Type G) S - Special voltage/plug (7) System Regulatory: A - CE B - CSA C - cULus D - CE/cULus E - CCC F - cCSAus H - cULus / NSF N - None S - Special (8) Tank Regulatory: A - CE B - ASME C - ASME Singapore D - GB (china) E - CRN F - ASME/CE G - ASME/CRN H - CE/UL S - Special L Number of matching Manufacturers is 1 Number of matching Products is 3 Processing time was o seconds Dragon Will Enterprise Ltd. 3Zj. Dongling Intelligent Electrical Appliances Technology Co., Starbucks Single Cup Brewer (CM9700)— Rapid Brewer for freshest coffee • Revolutionary rapid brewing system, fast brew coffee in 30s • 2 towers & 6 bean hoppers design for variety of coffee options and peak hour workloads. • High performance hot water dispenser, 5 mins preheat & 5L hot water output continuously. • Automated brewing, grinding and managing spent grounds frees up your partner to spend time with your customers • Recipe download, upload & firmware update by 10T • Quick access ground bins design Agency Listing nner C&S LISTED GWinner Commercial Equipment Award Core77 Design Awards 2022 E311353 Specification Production# Water Access Finish Hoppers Hopper Capacity Display 90300011503 Plumbed Black/Matt 6 2 Ibs (0.9kgs) Full color touch Electrical & Capacity Power Max Current Watts Plug type Phase dedicated 208 VAC 60 Hz Draw 40 A at 208 VAC Usage 8.32 kW at 208 VAC NEMA 14-50 (not supplied ) single Water & Plumbing requirements Pressure kPa Fitting Supplied pH Hardness Input H2O Temp. >_ 30 PSI at 1 gpm 250-350 3/8" Male NPT 6.5-8.5 90-140 ppm 60°F (15.5°C) Chlorine TDS Alkalinity Iron —<0.5 ppm 50-200ppm 20-140ppm < 0.3ppm Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. 22885 BREWER 23381 POWER CORD UNIT SHIPPING Height Width Depth Weight Height Width Depth Weight English 32" 22.5" 25.4" 330.7lbs 45" 44.9" 33.5" 429.9lbs Metric 81.3 cm 57.1 cm 64.5 cm 150 Kg 114.2 cm 114 cm 85 cm 195 Kg Aq )o rdT) TO WATT *Recommended countertop hole to be 4" (100mm) for power cord and water line. zhUse existing dedicated filtered water supply satisfying all Starbucks water requirements ,lUse existing dedicated 208 VAC, single-phase, 60 Hz, 50 Amp service dedicated line *Clover Vertica comes with 6 extra bean hoppers & 12 label holders. Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. 22885 BREWER 23381 POWER CORD �Oonll.in®Donlim Intelligent Electrical Appliances Technology Co., Ltd. Clover Vertica - Declaration of Conformity This Cut Sheet is intended to help you: • Understand the physical, water, and electrical site requirements for Clover • The Clover internal air gap conformance Site Requirements Water Requires a dedicated filtered water supply satisfying all Starbucks water requirements: • Chlorine < 0.5 ppm • Total Dissolved Solids 50-200 ppm • Hardness 90 —140 ppm • pH 6.5 — 8.5 • Alkalinity 20 —140 ppm • Iron < 0.3 ppm • Pressure >_ 30 PSI at 1 gpm (32 floz / 15s) critical to coffee quality and brewer performance. Electrical • Power dedicated 208 VAC 60 Hz • Receptacle To be determined by local code • Max Power Usage 8.32 kW at 208 VAC • Max Current Draw 40 A at 208 VAC Clover requires 208 VAC, single-phase, 60 Hz, 50 Amp service. It is recommended that the service be a dedicated line. Line voltage under load must lie within the specified range. Weight • Weight of each module < 120 lbs. (3 Modules which are connected) Weight excludes beans and drip tray; it includes hoppers, waste bucket, and residual water in the boiler. C UL US LISTED E311353 Dimensions 22.2" 31.9" Air gap 31.8" 2.0" GAP TO WALL 25.4" The distance of the "air gap" between the potable water outlet and the brewing chamber is 38.3mm (1.5"). Chemicals used for the cleaning process enter the system downstream of the air gap. Warnings f Clover is not intended for use by untrained persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the brewer by a person responsible for their safety. f The machine should be kept upright during operation 0 Machine to be installed with adequate backflow protection to comply with applicable federal, state, and local codes. 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction Two separate boxes are ordered with each Clover Vertica, one has the cord set and the other has the install kit you o should have 3 boxes to complete the install. i. Remove the clover Vertica from the pallet and boxes, each tower is individually packed and there are three boxes that hold extra parts and hoppers. Contents below: • 12-hoppers • 12-label holders 2. 2-coffee tower bottom cover (sheet metal) • 14-thumb screws • 20-coffee backsplash • 1 -water backsplash Place the water tower on its side on and install the cord set. • Remove the lower back panel • Thread the cord with the elbow strain relief into the back of the machine and connect the two hots and ground to the appropriate terminals then tighten the nut on the strain relief. Reattach the back panel. • Install the cord CamCo NEMA 14-50P cord cap from the install kit box 3. Place the two coffee towers on the counter with the "cut out" panel facing the water tower 4. Unpack 6 hoppers and put them on the machine 5. leave boxes unopened next to the machine. See example of hoppers on the machine below. No need to connect towers the commissioning supplier will do that. 12/14/23 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction Water Boost Kit The Pentair water boost kit comes with all the valves and supply hoses needed for connection. 3035 PSI POU T5Y WATERBOOST INSTALLATIONS KIT COMPONENTS rcNm f.6oY \` ua ` CYlN511� &WpO.LYmKl.dN Mm = -AM.- 1MlBR lr�.a 5 FYIRN] WEFIFNNMPI.I. WnGBP 1 V/�� 10 fYl�% rcBxMElPYffID.LBCOM Asn FY!®T vMCPD[gNW yd� EYlm54 LEES.YutrtF MG BY-- 4�wrr�w:rw.ylrcr.d.m.lra �� +PENT�N*RA. � # PENTAIR SHURFLO POU WATERBOOST, 30/35 PSI,115V SYSTEM INSTALLATION KIT GUIDE �Wt6 S WAIERROOSI SOLO SEPARATELY ,mm.l, �wruumNuwur Tn.�r,.o.emuNmuAmla Krcey� I.rmeso�.. mYt1E0b WwbaglmN maNlm of Me NU rcmtlm Tlem � a end �i.Vw �]IN89p.v.iapYlm.hEE10mP011 NA.lmnpinM.11fwmia Wmm Mol .am��. ralw�. m. neiwmoe aw.m n:. xm.. nmm�rq n.mNm rt �m �I w.a M,ne.n. 2. Remove cover and mount water boost and CV valve to the side of the cabinet under the Vertica, be careful not to penetrate screws into the opposite cabinet. 3. Connect supply hoses using the supplied install guide, penetrate holes in the cabinet as needed to run the hoses from the supply valve to the water boost and up to the Vertica. Do not turn on supply water or plug pump in. This will be done by the certified commissioning supplier. 12/14/23 22885 BREWER 23381 POWER CORD Dragon Will Enterprise Ltd. 3Zj. Dongling Intelligent Electrical Appliances Technology Co., Starbucks Single Cup Brewer (CM9700)— Rapid Brewer for freshest coffee • Revolutionary rapid brewing system, fast brew coffee in 30s • 2 towers & 6 bean hoppers design for variety of coffee options and peak hour workloads. • High performance hot water dispenser, 5 mins preheat & 5L hot water output continuously. • Automated brewing, grinding and managing spent grounds frees up your partner to spend time with your customers • Recipe download, upload & firmware update by 10T • Quick access ground bins design Agency Listing nner C&S LISTED GWinner Commercial Equipment Award Core77 Design Awards 2022 E311353 Specification Production# Water Access Finish Hoppers Hopper Capacity Display 90300011503 Plumbed Black/Matt 6 2 Ibs (0.9kgs) Full color touch Electrical & Capacity Power Max Current Watts Plug type Phase dedicated 208 VAC 60 Hz Draw 40 A at 208 VAC Usage 8.32 kW at 208 VAC NEMA 14-50 (not supplied ) single Water & Plumbing requirements Pressure kPa Fitting Supplied pH Hardness Input H2O Temp. >_ 30 PSI at 1 gpm 250-350 3/8" Male NPT 6.5-8.5 90-140 ppm 60°F (15.5°C) Chlorine TDS Alkalinity Iron —<0.5 ppm 50-200ppm 20-140ppm < 0.3ppm Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. 22885 BREWER 23381 POWER CORD UNIT SHIPPING Height Width Depth Weight Height Width Depth Weight English 32" 22.5" 25.4" 330.7lbs 45" 44.9" 33.5" 429.9lbs Metric 81.3 cm 57.1 cm 64.5 cm 150 Kg 114.2 cm 114 cm 85 cm 195 Kg Aq )o rdT) TO WATT *Recommended countertop hole to be 4" (100mm) for power cord and water line. zhUse existing dedicated filtered water supply satisfying all Starbucks water requirements ,lUse existing dedicated 208 VAC, single-phase, 60 Hz, 50 Amp service dedicated line *Clover Vertica comes with 6 extra bean hoppers & 12 label holders. Donlim reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. 22885 BREWER 23381 POWER CORD �Oonll.in®Donlim Intelligent Electrical Appliances Technology Co., Ltd. Clover Vertica - Declaration of Conformity This Cut Sheet is intended to help you: • Understand the physical, water, and electrical site requirements for Clover • The Clover internal air gap conformance Site Requirements Water Requires a dedicated filtered water supply satisfying all Starbucks water requirements: • Chlorine < 0.5 ppm • Total Dissolved Solids 50-200 ppm • Hardness 90 —140 ppm • pH 6.5 — 8.5 • Alkalinity 20 —140 ppm • Iron < 0.3 ppm • Pressure >_ 30 PSI at 1 gpm (32 floz / 15s) critical to coffee quality and brewer performance. Electrical • Power dedicated 208 VAC 60 Hz • Receptacle To be determined by local code • Max Power Usage 8.32 kW at 208 VAC • Max Current Draw 40 A at 208 VAC Clover requires 208 VAC, single-phase, 60 Hz, 50 Amp service. It is recommended that the service be a dedicated line. Line voltage under load must lie within the specified range. Weight • Weight of each module < 120 lbs. (3 Modules which are connected) Weight excludes beans and drip tray; it includes hoppers, waste bucket, and residual water in the boiler. C UL US LISTED E311353 Dimensions 22.2" 31.9" Air gap 31.8" 2.0" GAP TO WALL 25.4" The distance of the "air gap" between the potable water outlet and the brewing chamber is 38.3mm (1.5"). Chemicals used for the cleaning process enter the system downstream of the air gap. Warnings f Clover is not intended for use by untrained persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the brewer by a person responsible for their safety. f The machine should be kept upright during operation 0 Machine to be installed with adequate backflow protection to comply with applicable federal, state, and local codes. 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction Two separate boxes are ordered with each Clover Vertica, one has the cord set and the other has the install kit you o should have 3 boxes to complete the install. i. Remove the clover Vertica from the pallet and boxes, each tower is individually packed and there are three boxes that hold extra parts and hoppers. Contents below: • 12-hoppers • 12-label holders 2. 2-coffee tower bottom cover (sheet metal) • 14-thumb screws • 20-coffee backsplash • 1 -water backsplash Place the water tower on its side on and install the cord set. • Remove the lower back panel • Thread the cord with the elbow strain relief into the back of the machine and connect the two hots and ground to the appropriate terminals then tighten the nut on the strain relief. Reattach the back panel. • Install the cord CamCo NEMA 14-50P cord cap from the install kit box 3. Place the two coffee towers on the counter with the "cut out" panel facing the water tower 4. Unpack 6 hoppers and put them on the machine 5. leave boxes unopened next to the machine. See example of hoppers on the machine below. No need to connect towers the commissioning supplier will do that. 12/14/23 22885 BREWER 23381 POWER CORD Clover Vertica Pre commissioning GC Install Instruction Water Boost Kit The Pentair water boost kit comes with all the valves and supply hoses needed for connection. 3035 PSI POU T5Y WATERBOOST INSTALLATIONS KIT COMPONENTS rcNm f.6oY \` ua ` CYlN511� &WpO.LYmKl.dN Mm = -AM.- 1MlBR lr�.a 5 FYIRN] WEFIFNNMPI.I. WnGBP 1 V/�� 10 fYl�% rcBxMElPYffID.LBCOM Asn FY!®T vMCPD[gNW yd� EYlm54 LEES.YutrtF MG BY-- 4�wrr�w:rw.ylrcr.d.m.lra �� +PENT�N*RA. � # PENTAIR SHURFLO POU WATERBOOST, 30/35 PSI,115V SYSTEM INSTALLATION KIT GUIDE �Wt6 S WAIERROOSI SOLO SEPARATELY ,mm.l, �wruumNuwur Tn.�r,.o.emuNmuAmla Krcey� I.rmeso�.. mYt1E0b WwbaglmN maNlm of Me NU rcmtlm Tlem � a end �i.Vw �]IN89p.v.iapYlm.hEE10mP011 NA.lmnpinM.11fwmia Wmm Mol .am��. ralw�. m. neiwmoe aw.m n:. xm.. nmm�rq n.mNm rt �m �I w.a M,ne.n. 2. Remove cover and mount water boost and CV valve to the side of the cabinet under the Vertica, be careful not to penetrate screws into the opposite cabinet. 3. Connect supply hoses using the supplied install guide, penetrate holes in the cabinet as needed to run the hoses from the supply valve to the water boost and up to the Vertica. Do not turn on supply water or plug pump in. This will be done by the certified commissioning supplier. 12/14/23 22885 BREWER 23381 POWER CORD QOnLin Guangdong Xinbao Electrical Appliances Holdings Co.,Ltd Dragonwill Refrigerated Dispenser ♦ The equipment work within specification in an ambient temperature range between 60°F of 90°F and relative humidity range 0% to 90%. ♦ Milk refrigerator containing actively loaded milks, alt milk containers (Tetrapaks), and other refrigerated beverage components. Dispense product will be prechilled. ♦ User interface that is removable. ♦ Drip tray/waste capture that has option to be plumbed. ♦ Mounting bracket system for mounting on a wall ♦ The equipment refrigerate and store milk, alt milks, and other chilled ingredients at a safe holding temperature (3YF — 41°F). Existing container formats of milk can make minimal effort to attach to the dispense system. ♦ Equipment can automatically dispense liquid at recipe volumes into a Starbucks steaming pitcher (to be treated as the default dispense vessel) or into Starbucks cold cups by pressing button on panel C(DUS LISTED C31 1353 Specification • Two TFT screens show the Cavity temperature and milk mode. • Dispense prespecified Volume by press T/G/V or Tr button. • Dispense custom volume by press and hold "Free Flow" button until desired volume is dispensed then release the button. • Change Drink mode by choose the mode button(Shaken, Coffee Blended or Creme Blended) and show in the TFT screen. 4.6.5.1 Shaken: o Tall— 90g±15g o Grande — 120 g ± 15 g o venti — 180 g ± 15 g o Trenta— 240 g ± 15 g 4.6.5.2 Coffee Blended o Tall— 85g±15g o Grande — 110 g ± 15 g o Venti— 168g±15g o 4.6.53 Creme Blended o Tall— 112g±15g o Grande — 150 g ± 15 g o Vend— 224 g± 15 g • Change Fluid Type: Step 1: Press Shaken, Coffee Blended or Creme Blended button separately to change the mode. Step 2: While holding the Shaken button, press the free flow button to change the Fluid type (Dairy, Alt -dairy, Coconut Milk etc.). • Removable adapter system and BOM List. Items Description Material Usage 1 Rubber Silicone 1 PCs 2 Jar Bracket POM FG20-03 1 PCS 3 O Ring Silicone 1 PCS 4 Adapter POM FG20-03 1 PCs 5 Plunger rubber Silicone 1 PCS 6 Shaft Copper 1 PCs • Drip Tray and BOM List. 1 Hall Sensor N/A 1 PCS 2 Sensor cover plate ABS 750SW 1 PCS 3 Magnet ABS 750SW 1 PCS 4 Bottom plate ABS 750SW 1 PCS 5 Support plate ABS 750SW 1 PCS 6 Spring 302 Stainless Steel 2 PCS 7 Drip tray ABS 750SW 1 PCS 8 Guide plate ABS 750SW 1 PCS 7 • Mounting bracket system and BOM List. Items Description Material Usage 1 Right Support SPEC Steel 1 PCS 2 Left Support SPEC Steel 1 PCS 3 Joint Plate SPEC Steel 1 PCS 4 Left Guide SPEC Steel 1 PCS 5 Right Guide SPEC Steel 1 PCS 6 Fix bracket SPEC Steel 2 PCS 4 Electrical & Capacity Power Rated Current Rated Watts Plug type Phase 120 VAC 60 Hz 1.7 A 204W UL Plug Single Unit size & Package size Items Description Qty 1 Refrigerated Dispenser Unit 1 PCS 2 Drip tray 1 PCS 3 Adapter 2 PCS 4 Mounting bracket 1 PCS 5 Power cord 1 PCS / Unit Packa e size / Height Width Depth Weight Height Width Depth Weiht English 20.2" 10.4" 14.3" 17.6lbs 24.2" 18" 21.9" 37.5lbs Metric 512mm 265mm 364mm 8kg 617mm 458mm 558mm 17k Cleaning Instruction — Dish —washer clean requirement: The Adapter system (Rubber/Bracket/Adapter/Plunger) must cleaning with dishwasher at least two times every morning and every evening to keep the Adapter system sanitation before use and overnight. AP--M/ Remove Guide tube from unit and use dish —washer clean every morning and evening, then return to in position DI — Scrub and clean maintain requirement: The unit cavity must clean at least two times every morning and evening to keep the sanitation before use and overnight. 1. Turn off the unit power. 2. Open the door and scrub the cavity Upper/Down/Left/Right surface inclusive of the inside of door surface. 3. Remove the water tank of door and poor off all water than return to in position >CONVOTHERK Combi oven Convotherm mini easyTouch Standard features • Operating modes: o Steam (86-248°F) with guaranteed steam saturation o Combi-steam (212-482°F) with automatic moisture adjustment o Hot air (86-482°F) with optimized heat transfer o Rethermalization function • easyTouch user interface: 0 7" full touchscreen o Press&Go - automatic cooking and baking with quick access buttons o easyStart - automatic cooking and baking with product suggestions and smart recommendations o TrayTimer - load management for different products simultaneously o ecoCooking - energy saving function o LT cooking (low -temperature cooking) / Delta-T cooking o Cook&Hold - Cooking and keeping food warm in a single process o Programmable with an unlimited number of cooking profiles including up to 99 steps each and a picture o On -screen help o Preset start time • Multi -point core temperature probe • Robust rotary door lever with safety lock and sure -shut function • Preheat and cool down function • Flexible shelf spacing • Steam reducer • Safe Cooldown (can be enabled through the service interface) • Fully automatic ConvoClean cleaning system Project Item Quantity_ FCSI section Approval Date ■ easyTouch • Electric • Capacity 10 shelves • Injection 13" x 18" • Right -hinged door Key features • 4 operating modes: Steam, combi steam, convection, rethermalization • Extra functions: o Crisp&Tasty - 3 moisture -removal settings o BakePro -Traditional baking function with 3 settings (plus steam and rest phases) o Reduced fan speed and auto reverse mode • easyTouch 7" full -touch screen • ConvoClean system, fully automatic cleaning system with express mode and Safe Cool Down function before cleaning • Ethernet port (LAN) • USB port integrated in the control panel • Steam generated by injecting water into the oven cavity (without steam boiler) • Right -hinged door • UL listed ventless (KNLZ) no hood required, local codes prevail Options • Matte -black -on -stainless -steel exterior • Unit door with left-hand hinge • Various voltages (single-phase on request) • Ethernet connection RJ45 Accessories • Spray head with continuously adjustable flow regulation • Halton condensation hood • Equipment stands in various sizes and designs • Care products • Pans • Trays • Racks • Baskets • Grilling accessories Commercial combination oven with integral systems for limiting the emissions of grease laden air. This product conforms to the ventless operation recommendations set forth by NFPA96 using EPA202 test method. cL us LISTED CD O Welbilt Inc. Phone 1-800-338-2204 www.convotherm.com 18301 St. Clair Avenue WELBILT Cleveland, OH 44110 USA t> 1 9 CD O OWE >11CONVOTHERM; Front view ®uCM c a 16.9 20.3 7 View from above with wall clearances Dimensions and weights Dimensions including packaging Width x height x depth 22.8 x 46.3 x 35.8 " Weight Empty weight without packaging 153 Ibs Packaging weight 29 Ibs Safety clearances* Rea r 2.0 " Right-hand side 2.0 " Left-hand side (larger gap recommended for 2.0 " servicing) Top** 20.0 " Dimensions Weights Views Side view Connection points, unit floor A Water connection (soft water (filtered), for water injection) B Water connection (cold water (unfiltered), for cleaning) C Drain connection 1.5" D Electrical connection E Electrical Ground F Rinse -aid connection G Cleaning -agent connection H Air vent 0 1.18" 1 Dry air intake 0 1.69" M Safety overflow 2.36" x 0.79" N Ethernet connection RJ45 Installation requirements Max. absolute appliance inclination during max. 2° (3.5%) operation 2 * Minimum clearance to heat sources, 20". **Depends on the type of exhaust system and the ceilin%'s characteristics. CONVOTHERK Loading capacity Max. number of food containers [Unit has 5 sliding rails; rail spacing 2.68" max.] 13" x 18" half size sheet pans 10 12" x 20" by 2 1 /2" steam table pans 5 12" x 20" wire fry baskets 6 Plates, max 0 11" 12 Max. loading weight Per combi oven 66 Ibs Per shelf level 11 Ibs Electrical supply 3— 208V-240V 60Hz (3/PE) (for 208V) Rated power consumption 8.50 kW Hot air power 8.16 kW Motor output 0.25 kW Rated current 23.6 A Supplied with a 4 conductor 6 foot long cord AWG 8 Conductor insulation rating SOOW Plug (customer supplied) 15-50P or L15-50P 3— 208V-240V 60Hz (3/PE) (for 240V) Rated power consumption 11.25 kW Hot air power 11.12 kW Motor output 0.25 kW Rated current 27.1 A Supplied with a 4 conductor 6 foot long cord AWG 8 Conductor insulation rating SOOW Plug (customer supplied) 15-50P or L15-50P Capacity Electrical specifications Water Water connection Water supply Shut-off device The unit may need to be installed with an appropriate backflow preventer in order to comply with all applicable federal, state, and local laws and regulations. Water supply Two 3/4" inner diameter GHT-M (garden hose adapter). The unit is designed for a permanent hookup to the water supply that uses a connecting hose with a minimum diameter of 1/2" Flow pressure, 29 - 87 psi (2 - 6 bar) without ConvoClean system Flow pressure, 43.5 - 87 psi (3 - 6 bar) with ConvoClean system Appliance drain Version Naturally ventilated pipe to open pan or drain/channel, min. 1" ventilation clearance Type Depending on the length ofthe line and the elements used in the line, the minimum inner diameter of the line is 1.5". Water quality Water connection A* for water injection General Drinking water, typically soft water requirements (install a water treatment system if necessary) TDS 70-125ppm Hardness 70 - 125 ppm (4-7 gpg) Water connection B* for cleaning General Drinking water, typically untreated requirements water TDS 70 - 360 ppm Hardness 70 - 360 ppm (4-21 gpg) Water connections A, B* pH value 6.5 - 8.5 Cl- (chloride) max. 60 ppm Cl2 (free chlorine) max. 0.2 ppm S042-(sulfate) max. 150ppm Fe (iron) max. 0.1 ppm Si02 (silica) max.13 ppm NH2CI (monochloramine) max. 0.2 ppm Temperature max. 104 °F / max. 40 °C * Please refer to connection points graphic, p. 2. NOTICE: The owner/operator/purchaser must ensure that the water quality requirements are met. Otherwise the unit warranty is void. I X O O !>CONVOTHERM; Water consumption Water Emissions Accessories F.191"I61017M Water connection A* (For more detailed information, please refer to the Accessories brochure.) 0 water consumption during cooking 0 - 4.0 gph Max. water throughput 0.13 gpm Water connections A, B with ConvoClean system 0 water consumption during cooking** 0 - 5.3 gph Max. water throughput 2.6 gpm * Values intended as guide for specifying the water treatment system. ** Incl. water required for cooling the wastewater. NOTICE: See connection positions diagram, p. 2. Emissions Dissipated heat* Latent 1740 BTU/h Sensible 1911 BTU/h Drain temperature max. 140°F / 60°C Decibel rating max. 60 dBA Please note: • This document is to serve planning purposes only. • Please refer to the Installation manual for further technical data and for instructions on installation and setup. M Welbilt Inc. Phone 1-800-338-2204 www.convotherm.com 18301 St. Clair Avenue Cleveland, OH 44110 USA t> WELBILT' 19278 I I I I I I I I o I � I I I � I I I R3/4 [R19] 5 11/16 [144] 11 3/8 [289] WRAP �z Lu Lu 3: z Lu pj U �g 00 Ln 1 11/16 [431 1 1 3/16 [29]� R3/4 [R19] 17 5/16 [440] LID NOT SHOWN IN TOP VIEW 15 [381] 11 3/4 [299] WELD 1 5/8 [41] STUD PLACEMENT 0 0 In o _o o I N TUB TO BE DIE STAMPED TO A MINIMUM 1/4" [6] DEPTH TO ENSURE PROPER DRAINAGE 8 3/16 [2081—{ 16 3/8 [416] WRAP 01 3/8" [35] DRAIN HOLE TO BE DIMPLED MIN. 1/8" [3] IN DEPTH TO ENSURE BRASS DRAIN FITS FLUSH GENERAL NOTES: CUSTOMER: STARBUCKS 1. NO BURRS OR DIE MARKS PERMISSIBLE PROJECT: 45LB ICE BIN W/ SIDE ACCESS LID POLISHED TOAMAT)HINGFINISH 2. ALL WELDS TENSION GROUND SMOO(H (UNLESS 3. OVERALL DIMENSION TOLERANCE UNLESS NOTED OTHERWISE NSF® 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/-.25[6.35] ITEM #: DATE: 01/17/18 DRAWN BY:TCP / DW REV NSFID: CUSTOM COMPONENT THISPRINT IS LOANEDHE SUBJECERTY T FACT RING OREHULKAY AN UPONDEMA COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDRION THAT IS IS NOT TO BE USED REV FSP #: FSP211635 SHEET: 1 OF 4 PURPOSES OTHER DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR THAN THOSE FOR WHICH IT WAS FURNISHED. C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LBICE BIN - SIDE ACCESS.DWG 19278 � �17 5/16 [440]� r-12 5/16 [313]� 1 T 4-7/16 [10] T 7/16 [10] Lo Lo QD M F11/16 [18] �16 3/8 [416] �—ll 3/8 [289] BIN SECTION VIEWS 131Vj,`3I��SJl�r6J O j L 1 [25] �7/8 [22] 01/4 [6] 18 GA. [1.2] CONSTRUCTION ALL CORNERS PERFORATED TRIVET TO FIT FULLY WELDED INSIDE TUB RADIUS AND HAVE AND POLISHED FINGER HOLES FOR REMOVAL PERFORATED TRIVET GENERAL NOTES: 1. NO BURRS OR DIE MARKS PERMISSIBLE 2. ALL WELDS TO BE GROUND SMOOTH AND POLISHED TO A MATCHING FINISH 3. OVERALL DIMENSION TOLERANCE (UNLESS NOTED OTHERWISE) 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.35] REV REV 14 GA. [2.0] CONSTRUCTION TOP 16 GA. [1.5] CONSTRUCTION TL FULLY WELDED AND POLISHEC TO A 304 #4 FINISH 2 [51] 1 1/2 [38] 1 1/4 [321 1 1" NPS BRASS DRAIN WITH FLANGED ZINK LOCKNUT AND RUBBER WASHER 7/16 20 GA. [1.0] 304 S/S CONSTRUCTION WRAP TO BE INSULATED WITH 1/2" [13] FOIL FACED RIGID FOAM — AT SIDES AND BOTTOM (SILICONE ALL SEAMS) FUSE WELD 1" [251 LONG WELD STUD TO BOTTOM OF INNER TUB 03/8" [0101 HOLES IN INSULATION AND WRAP FOR WELD STUD WELD STUD AND CAP DETAIL Scene: N.T.S. CUSTOMER: STARBUCKS ATTACH TO INSULATED WRAP BY MEANS OF 4 EACH WELD STUI AND STUD CAPS PROJECT: 45LB ICE BIN W/ SIDE ACCESS LID ITEM #: DATE: 01/17/18 DRAWN BY:TCP / DW NSF ID: CUSTOM COMPONENT FSP #: FSP211635 I SHEET: 2 OF 4 01 3/8" [35] DRAIN HOLE TO BE DIMPLED MIN. 1/8" [3] IN DEPTH TO ENSURE BRASS DRAIN FITS FLUSH 02 5/8" [067] BY 1/2" [13] TALL �S/S RING STITCH WELDED TO INSIDE OF WRAP (SILICONE INSIDE SEAM) NSF® rr THIS PRINT IS THE PROPERTY OF ELKAY MANUFACTURING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LBICE BIN -SIDE ACCESS.DWG 19278 NOTE: 1/2 [13] SECTION TYP. Ll @ 4 SIDES _r- 5/8 [16] 18 GA. [1.2] 304 #4 NSF STICKER (COMPONENT) 5/8 [16] 3/16 [5] 11/16 [1R1 GENERAL NOTES: CUSTOMER: STARBUCKS 1. NO BURRS OR DIE MARKS PERMISSIBLE PROJECT: 45LB ICE BIN W/ SIDE ACCESS LID 2. OALL VERALDIMENSGROUNDSMOO(H POLISHED 3. OVERALL DIMENSION TOLERANCE UNLESS NOTED OTHERWISE NSF® 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/- .25 [6.351 ITEM #: DATE: 01/17/18 DRAWN BY:TCP DW REV NSFID: CUSTOM COMPONENT THIS PRIND IS ZONEDHE SUBJECERTY T FACT RING COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND ORErULKAY AN UPONDEMA AND UPON THE EXPRESS CONDITION THAT IS IS NOT TO BE USED REV FSP #: FSP211635 SHEET: 3 OF 4 PURPOSES OTHER DIRECTLY OR INDIRECTLY WITHOUT OUR PERMISSION FOR THAN THOSE FOR WHICH IT WAS FURNISHED. C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LBICE BIN -SIDE ACCESS.DWG 19278 0 Ln `J I I DETAIL -B- 3 7/8 [99] O.D. R3/4 [R19] 18 GA. [1.21 304 #4 S/S CONSTRUCTION 18 GA. [1.21 304 #4 S/S CONSTRUCTION DIE STAMP UP 1/8" MINIMUM 18 GA. [1.21 304 #4 S/S CONSTRUCTION DIE STAMP UP 1/8" MINIMUM � 11/16 [17] 4 1/4 [108] O.D. �S �\ .0 4399J 2 1/8 [54] O.D. 1 [25] BACK FLANGE W/ 2 EA. HOLES TO SLIDE OVER THREADLESS WELD STUDS 3 3/8 [86] O.D. GENERAL NOTES: CUSTOMER: STARBUCKS 1. NO BURRS OR DIE MARKS PERMISSIBLE POLISHED EDOTORWISE) MATCHING FINISH 2. ALL OVERALDS TO BE DIMENSGROUNDSMOO(H (UNLEND SS 3. OVERALL DIMENSION TOLERANCE UNLESS NOTED OTHERWISE PROJECT: 45LB ICE BIN W/ SIDE ACCESS LID NSF® 3.1. SHARP BENDS +/- .125 [3.18] 3.2. ROLL BENDS +/-.25[6.35] ITEM #: DATE: 01/17/18 DRAWN BY:TCP / DW REV NSFID: CUSTOM COMPONENT THISPRINT IS LOANEDHE SUBJECERTY T FACT RING OREHULKAY AN UPONDEMA COMPANY AND IS LOANED SUBJECT TO RETURN UPON DEMAND AND UPON THE EXPRESS CONDRION THAT IS IS NOT TO BE USED FSP #: FSP211635 SHEET: 4 OF 4 DIRECTLY H INDIRECTLYTHAN PURPOSES OTHER THAN THOSE FOR WHICH IT WAS FURNISHED. HOSE FOR T OURWHICH IT WAS PERMISSIONFORREV C:\VAULTEPDM\FSP ENGINEERING\PROJECTS\STARBUCKS\45 LB ICE BIN WITH SIDEWAYS OPEN LID-74763A\FSP211635\FSP211635_45LBICE BIN - SIDE ACCESS.DWG Features Horizon Elite ❑ 1010 series - up to 1061 lb (482 kg) in 24 hours ❑ 1410 series - up to 1466 lb (665 kg) in 24 hours - automatically transport ice through a tube with RIDE® technology from up to 75' (22.9 m) away - chewable, compressed nugget ice is preferred over cubes' - Chewblet ice dispenses reliably from ice and beverage dispensers - available with approximately 1.00" (2.54 cm) long standard Chewblet ice or optional 3/8" (0.95 cm) long Micro Chewblet'" ice - quiet production without noisy harvest cycles Revolutionary, scale inhibiting design - produces ice that has 15% the TDS of the incoming water for optimum dispensing and long life in drinks - quarantines and regularly expels scale producing dissolved solids to dramatically reduce scale buildup - increases time between descaling and reduces or eliminates the need for expensive scale treatment - saves 35% water compared to comparable cubers Durable, attractive ice machine - regular bearing inspection or replacement is not required - upgraded, easy -to -read LED operating status and diagnostic display Designed with sanitation in mind - Agion® silver -based antimicrobial product protection of key ice and water contact componentS2 - floatless, sealed design inhibits formation of biofilms - semi -automatic cleaning and sanitizing system Warranty - 3 years parts and labor, 5 years compressor parts Certifications NSF i'1T0"s Independent third parry studies. Contact Follett for details. Disclaimer: Antimicrobial protection is limited to the treated components and does not treat water or ice. 3 Refer to price list for additional warranty information. Horizon Elite" self-contained 1010, 1410 series Chewblet° ice machine Short form specification: Ice machine to be a Follett' Horizon Elite ice machine model [Insert size/series, condenser type and installation/mounting, from model number guide] capable of producing compressed nugget ice using an efficient, sanitary horizontal evaporator/auger system and delivering ice by a flexible wire reinforced transport tube to ❑ ice storage bin, ❑ ice and water dispenser, ❑ ice and beverage dispenser, ❑ drop -in dispenser or ❑ Ice Manager- divertervalve system, slide -out compressor/condenser/evaporator with utility docking station, front -mounted unit status display, evaporator water inlet at harvest end with automatic flush while producing ice, and semi -automatic cleaning and sanitizing system, plus all the features listed below and mounting/ performance -enhancing accessories checked. Model configurations Nk Install/ Item number' Item number' For use with' mount Condenser V/Hz/Ph 1010 series 1410 series 208-230/60/1 HCC1010ABT HCC1410ABT top air 230/50/1 HCE1010ABT HCE1410ABT 208-230/60/1 HCC101OWBT HCC141OWBT mount ice storage bin water 230/50/1 HCE101OWBT HCE141OWBT 208-230/60/1 HCC1010ABS HCC1410ABS air 230/50/1 HCE1010ABS HCE1410ABS RIDE 208-230/60/1 HCC101OWBS HCC141OWBS water 230/50/1 HCE101OWBS HCE141OWBS Follett Vision" undercounter ice and beverage RIDE air 208-230/60/1 HCC1010AVS HCC1410AVS 230/50/1 HCE1010AVS HCE1410AVS 208-230/60/1 HCC1010WVS HCC1410WVS dispenser water 230/50/1 HCE1010WVS HCE1410WVS 208-230/60/1 HCC1010AHT HCC1410AHT top air 230/50/1 HCE1010AHT HCE1410AHT water 208-230/60/1 HCC1010WHT HCC1410WHT countertop ice and beverage mount' 230/50/1 HCE1010WHT HCE1410WHT 208-230/60/1 HCC1010AHS HCC1410AHS dispenser (by others) air 230/50/1 HCE1010AHS HCE1410AHS RIDE 208-230/60/1 HCC1010WHS HCC1410WHS water 230/50/1 HCE1010WHS HCE1410WHS 208-230/60/1 HCC1010AJS HCC1410AJS drop -in dispenser (by others) RIDE air 230/50/1 HCE1010AJS HCE1410AJS 208-230/60/1 HCC1010WJS HCC1410WJS water 230/50/1 HCE1010WJS HCE1410WJS Ice Manager diverter air 208-230/60/1 HCC1010AMS HCC1410AMS valve system RIDE water 220/60/1 HCC1010WM5 HCC1410WM5 ' Ordered separately. z For Micro Chewblet ice, replace second character (C) with an M e.g. HMC1010ABT. I Requires top kit (see page 4 for item number). 23183 HMC 1410ABT 23185 HMC 1010ABT 1.8 Church Lane 1 Easton, .7101 1 f USA �OLLEIT 1.800.523.9361 11.610.252.7301 I follettice.com 231837 23185 Accessories Dimensional drawing ❑ Top kit for ice and beverage dispensers (listed on page 4) ❑ Water filters (refer to form# 9905) ❑ Wall mount bracket (item# 01085455) ❑ Ice machine stand, height -adjustable (item# 01085463) ❑ Timer to control one or two ice machines (item# 00967265) ❑ Longer ice transport tube (refer to the price list, form# 4025) NOTE: 10' (3 m) provided as standard for RIDE model. ❑ Sleep cycle kit for improved energy efficiency and component life (item# 01338276) NOTE: For countertop dispenser applications for models ending in HS and HT. ❑ SafeCLEAN PIusTM ice machine cleaner ❑ 1 x 8 oz (237 ml) bottle (item# 01 147826) ❑ 6 x 8 oz (237 ml) bottles (item# 01149954) ❑ 24 x 8 oz (237 ml) bottles (item# 01149962) ❑ SaniSpongeTM, 24 sanitary sponges (item# 01075431) Specification i nta ke for 1410 models only 1 zo.aa° C1 2.9 cm) 17.49" (44.4 cm) 15.00" (38.1 cm) 2.73" (6.93 cr 3.34"- (8.48 cm) Horizon Elite 1010 series Horizon Elite 1410 series W1 Width 29.15" (74.0 cm) 29.15" (74.0 cm) 1131 Depth 23.25" (59.1 cm) 25.15" (63.9 cm) H1 Height 22.50" (57.2 cm) 22.50" (57.2 cm) AIR CSoo 00 :3 00 0 0 0 0 O � 0 C7 C6 0 0 O . 2.30" 12.25" (31.1 cm) Clearance top, left and right-1.00" (2.54 cm) top, left and right-1.00" (2.54 cm) Electrical (HCC models) C1 11 amps, requires dedicated 15 amp circuit, C1 14 amps, requires dedicated 20 amp circuit, 208-230 V/60/1 6' (1.8 m) cord, NEMA 6-15 plug 6' (1.8 m) cord, NEMA 6-20 plug Electrical (HCE models) C1 11 amps, requires dedicated 15 amp circuit, C1 14 amps, requires dedicated 20 amp circuit, 230 V/50/1 6' (1.8 m) cord only, no plug 6' (1.8 m) cord only, no plug Operating power 2.4 kW C2 Ice transport tube see page 8 for details C3 Water inlet 3/8" OD push -in water inlet- internal connection C4 Drain 3/4" MPT, 1 " drain required. See page 7 for details. C5 Ice bin signal cord for Vision applications only Water-cooled ice machine C6 - 1 /4" FPT condenser inlet connections C7 - 1 /4" FPT condenser outlet Air temperature 50 -100 F (10 - 38 C) Water temperature 45 - 90 F (7 - 32 C) Potable water pressure 10 - 70 psi (69 - 483 kPa) Condenser water pressure 30 - 150 psi (207-1034 kPa) Ice production 60 Hz models and 50 Hz water-cooled models see page 8 50 Hz air-cooled models at 70 F (21 C) air, 50 F (10 C) water - 865 lb (393 kg) 50 Hz air-cooled models at 90 F (32 C) air, 70 F (21 C) water - 734lb (333 kg) Energy consumption air-cooled models -4.80 kWh 90 F (32 C) air, water-cooled models -4.20 kWh 70 F (21 C) water per 100 lb (45.4 kg) ice Heat rejection air-cooled models -11,300 BTU/hr (2,849 Kcal/hr) water-cooled models- 12,800 BTU/hr (3,228 Kcal/hr) Water consumption 12.0 gal (45 L) of potable water per 100 lb (45.4 kg) of ice (per AHRI test standards). 12.4 gal (46.9 L) at low TDS flush setting. Water flow requirement 1 gallon per minute for water-cooled models Refrigerant R404a for 60 Hz models and 50 Hz water-cooled models R449a for 50 Hz air-cooled models Approximate ship weight 275 Ib (125 kg) Approximate net weight 265 Ib (120 kg) NOTE: For indoor use only 3.1 kW see page 8 for details 3/8" OD push -in water inlet- internal connection 3/4" MPT, 1 " drain required. See page 7 for details. for Vision applications only C6 - 1 /4" FPT condenser inlet C7 - 1 /4" FPT condenser outlet 50-100F(10-38C) 45-90F(7-32C) 10 - 70 psi (69 - 483 kPa) 30 - 150 psi (207-1034 kPa) 60 Hz and 50 Hz models see page 8 air-cooled models -4.84 kWh water-cooled models -3.80 kWh per 100 lb (45.4 kg) ice air-cooled models - 16,000 BTU/hr (4,035 Kcal/hr) water-cooled models - 16,400 BTU/hr (4,135 Kcal/hr) 12.0 gal (45 L) of potable water per 100 lb (45.4 kg) of ice (per AHRI test standards). 12.3 gal (46.5 L) at low TDS flush setting. 1 gallon per minute R404a for 60 Hz and 50 Hz models 305 lb (138 kg) 295 lb (134 kg) orm#7030 23183, 2318811-contained 1010, 1410 series ice machine 1 — Locating the ice machine Horizon Elite self-contained Chewblet ice machines allow top -mounting or mounting in abase cabinet, on a wall or on a floor stand up to 75' (22.9 m) from the dispenser or ice bin with RIDE technology. In -cabinet mounting (RIDE applications) require special attention to service access, unit ventilation and ice tube runs (see pages 4-8). Top mounting - ice and beverage RIDE model - Follett low -profile Vision Top mount on Follett ice storage bins dispensers (by others) ® ice and beverage dispensers e 0 Important specifier notes Important specifier notes Important specifier notes 1. Dispenser must be compatible with 1. See page 4-6 for critical clearance and 1. See form# 8590 for bin sizing. nugget ice. See page 4 for compatible ice venting requirements. 2. Verify ceiling or soffit height to ensure and beverage dispenser models and top kit numbers. 2. Ice transport tube ships with Vision top clearance. 2. Verify ceiling or soffit height to ensure ice and beverage dispenser (Vision applications only). 3. Locate floor sink or grate and drains in front of storage bin. sufficient top clearance. 4. Do not position bin drain lines to block Ice•Devlce" bin cart. RIDE model - ice and beverage RIDE model - drop -in beverage RIDE model - Follett ice storage bins dispensers (by others) dispensers (by others) a a Important specifier notes Important specifier notes Important specifier notes 1. Dispenser must be compatible with nugget 1. Compatible with the following dispensers: 1. See form# 8590 for bin sizing. ice. Compatible dispensers include Coca-Cola Cornelius 1522, 1722, 2323, and Lancer 2. Locate floor sink or grate and drains in front Freestyle 9000, Cornelius DB/ID/DF150/175, 2200, 2300, 23300. of storage bin. Lancer 4500-22N, FS-16N, FS-22N and FS-44N, Servend MD150/175/200/250, 2. Require 12.00" (30.5 cm) of access space for 3. Do not position bin drain lines to block SW 75/200/250, MDH-402 and installation on transport tube side. Ice*DevIce bin cart. Follett Symphony PIusTM 110CM, as well as 3. See page 4-6 for critical dispensers listed on page 4. clearance requirements. 2. Coca-Cola Freestyle 7100 requires top adapter IC Code 46751 and ice kit IC Code 46430 only, and must be ordered from Coca-Cola. Coca- Cola Freestyle 9100 requires top kit HSF26SC. Consult with Coca-Cola and Follett to qualify application prior to ordering. 3. RIDE application is approved only for Pepsi Spire 3.0, 5.0 and 4.1 designed for top mount ice machines and requires MSP24SC for 3.0 and MSP30SC for 5.0 and 4.1, ordered separately. For manual fill versions of Pepsi Spire 3.0, 5.0 and 4. 1, contact factory. 4. Seepage 4-6 for critical clearance and venting requirements. Self-contained 1010, 1410 series ice machii231 83, 23185 Form#7030 1 - Locating the ice machine (continued) Top mounting -compatible ice and beverage dispensers' Width Depthz Height3 Manufacturer Model number in (cm) in (cm) in (cm) Top kit Freestyle 7000 30.10 (76.5) 33.11 (84.1) 47.00 (119.38) H30F30-F4 Coca-Cola dispensers Freestyle 7100 30.00 (76.2) 33.80 (85.8) 47.00 (119.4) H30F30-F4 6 DB/ED/DF 200 series 30.00 (76.2) 30.00 (76.2) 34.38 (87.3) H3CC3C-F DB/ED/DF 250 series 30.00 (76.2) 30.00 (76.2) 38.38 (97.5) H30C30-F DB/ED/DF 300 series 44.00 (111.8) 30.00 (76.2) 34.00 (86.4) H30C44-(F or B) 6 Cornelius dispensers FlavorFusion / Overload 30.00 (76.2) 33.13 (84.2) 39.38 (100.0) H3CC3C-F-FF IDC215 30.00 (76.2) 33.13 (84.2) 39.38 (100.0) H30C30-F-IDC IDC255 and Pro Fast Gate 30.00 (76.2) 33.13 (84.2) 36.38 (92.4) H30C3C-F-IDC IDC Pro 30.00 (76.2) 33.13 (84.2) 40.25 (102.2) H3CC3C-X-PRO7 4500-30N 30.00 (76.2) 30.50 (77.5) 36.50 (92.7) H3CL3C-F FS-30N 30.00 (76.2) 30.50 (77.5) 42.13 (107.0) H30L30-F Bevariety 30.00 (76.2) 31.00 (78.7) 37.75 (95.9) H22L30-F-STP Lancer dispensers Sensation 30" 30.00 (76.2) 31.00 (78.7) 38.25 (97.2) H3CL3C-F-STP Sensation 44" 44.00 (111.8) 31.00 (78.7) 39.38 (100.0) H22L44-F-STP Touchpoint 32.50 (82.6) 33.70 (85.6) 40.00 (101.6) H3CL3C-F-STP Pepsi dispensers Spire 5.0 / 4.1 30.50 (77.5) 36.00 (91.4) 42.75 (108.6) H3CP30-F Servend dispensers MDH-302 42.80 (108.7) 31.00 (78.7) 32.38 (82.2) H3CS44-(F or B)6 'All approved dispensers can be filled with a RIDE model Horizon Elite ice machine without atop kit except for Pepsi Spire 3.0, 5.0 and 4.1, seepage 3 for details. Requires minimum 1.00" (2.54 cm) clearance between back of dispenser and wall. s Net height after installation of top kit (excluding height of ice machine). 4 Consult with Coca-Cola and Follett to qualify application prior to ordering. 6 Top adapter IC Code 46753 and ice kit IC Code 46430 must also be ordered from Coca-Cola. 6 Specify 7" for front facing, or"B" for backward facing units. 'Top designed with flexibility to accommodate front or back mounting. 2 - Undercounter/in-cabinet mounting Cabinet details Important specifier notes 1. Cabinet door opening must meet minimum size requirements shown and be free of obstructions to allow ice machine to slide out (no lip or utilities to block removal). 2. Cabinet base must be capable of supporting ice machine and allow ice machine to rest flat on cabinet bottom. 3. No counter supports, electric or plumbing can run in front of the ice machine. Cabinet door opening 1010/1410 series models require 31.00"W x 23.5"H (78.7 cm x 59.6� F4orm#7030 23183, 23188If-contained 1010, 1410 series ice machine 3 — Undercounter/in-cabinet mounting and ventilation Using Follett supplied grilles Horizon Elite ice machines can be installed undercounter/in-cabinet to fill bins or dispensers using RIDE technology. Care must be taken to ensure proper cabinet venting to avoid recirculation of hot air. Improper venting can cause ice machine outages. Horizon Elite Supplied ice machine grilles 18. cm Ice transport tube P minimum minimum imu minimum 1/4" perfoot (2 cm per meter) 25.25" (64.1) cm) pitch toward ice machine minimum -'I --- - -'---_ secure to prevent dips and traps from forming r I NL+ see dispenser electric, specification sheetfor _ installation L r +,water requirements drain - 23.50" (59.69 cm) minimum Cabinet door must mate directly 12.00" (30.5 cm) minimum to air intake gasket between ice machine and dispenser Horizon Elite ice machine air intake gasket Completed installation with gasket and door in place — cabinet door Side view 25.25" (64.1 cm) min. ----- ------------------- Front 23.50" locating 2.25" (5.72 cm) (59.7 cm) cutout cutout minimum � 2.00" - -- (5.08 cm) bottom of ice machine side of ice machine cutout for supplied air intake grille supplied intake grille 24.00"W x 16.00"H (61.0 cm x 40.6 cm) Important specifier notes for using Follett supplied grilles 1. The supplied exhaust grille must be located at least 18.00" (45.7 cm) 4. Cabinet door must mate directly to air intake gasket. from the supplied air intake grille (exhaust air must not recirculate 5. Cabinet interior must provide a minimum clear space of 23.50" with intake air). (59.7 cm) high by 25.25" (64.1 cm) deep. 2. Cabinet interior must be open to allow for unrestricted exhaust 6. Cutout for supplied grilles must meet minimum size requirements air flow. shown above. 3. Ice transport tube needs minimum 1 /4" per foot (2 cm per meter) 7. Utilities should be conveniently located as shown. pitch toward ice machine and should be secured to prevent dips and traps from forming. Self-contained 1010, 1410 series ice machir231 83, 23185 Form#7030 3 — Undercounter/in-cabinet mounting and ventilation (continued) Using grilles by others/alternate cabinet ventilation Cabinets with ventilation or louvers other than those provided require special consideration to provide proper ventilation. Recirculation of hot air will reduce ice machine performance and can cause ice machine outages. Grilles by others/ alternate cabinet ventilation 18.00" (45.7 cm) minimum 18.00" (45.7 cm) minimu All counter ventilation cabinet door within 18.00" (45.7 cm) of must mate directly air inlet must be blocked to to air intake gasket prevent exhaust -air recirculation Minimum open air space Horizon Elite ice machine air intake gasket cabinet door / x ® x x y x n = sq. in. of open air space n= (# of openings) side minimum 250 sq. in. view open air space y Grilles by others/ alternate cabinet ventilation Important specifier notes for using grilles supplied by others/alternate cabinet ventilation 1. Exhaust must be at least 18.00" (45.7 cm) from air intake (exhaust air 4. Ducting must be provided if cabinet door does not mate directly to must not recirculate with intake air). air intake gasket. 2. Cabinet interior must be open to allow for unrestricted exhaust 5. Cabinet interior must provide a minimum clear space of 23.50" air flow. (59.7 cm) high by 25.25" (64.1 cm) deep. 3. Ice transport tube needs minimum 1 /4" per foot (2 cm per meter) 6. Grilles by others must meet minimum requirements for open air pitch toward ice machine and should be secured to prevent dips and space shown above. traps from forming. 7. Utilities should be conveniently located as shown. Form#7030 23183, 23188If-contained 1010, 1410 series ice machine 4 — Horizon Elite ice machine mounting accessories Optional wall mount bracket Optional machine stand Important specifier notes 1. For secure wall mounting, specify optional wall mount bracket. O O 2. Wall and fasteners must support the weight of the ice machine, bracket, supply water and ice. Use of a backing board may be required with hollow wall construction. v O 3. Machine stand mounting adds 6.88" (17.5 cm) to height of ice machine. 4. No dips in tube routing allowed. 5. Ice transport tube needs minimum 1 /4" per foot (2 cm per meter) pitch 6.88" toward ice machine and should be (17.50 cm) secured to prevent dips and traps from forming. o� 22.00" (55.9 cm) B A 13.00" / a 100 (33.0 cm) 0 25.50" A - 25.2" (64.0 cm) (53.3 cm) 30.50' " (64.8 cm) (77.7cm) y/i\ B - 28.7" (72.9 cm) 5 — Horizon Elite drain - specifier guidelines Flush drain plumbing - For regular machine drainage Important specifier notes: Where code allows, follow recommendation below. 1. Connect the silicone tubing to the ice machine O 3/4" drain barb O. 2. Assemble the 3/4" barb x 3/4" FPT to the 3/4" Minim adieus MPT x 1 " slip. Connect the other end of the silicone tubing to the 3/4" barb ©. 2ftx1°oD 3. Connect the 1 " slip fitting to the 1" stand pipe/ cone tubing drain Q. Note: Minimum 8" radius on silicone drain line. 3/4" barb x 3/4" FPT Drain line from the ice machine must have at least © 1 /4" per foot pitch (6.4 mm/0.3 m). 3/4" MPTx 1" slipFRI Note: Stand pipe/drain provided by others. All Q1"Stand pipe/drain other components provided with ice machine. Chassis drain plumbing — To assist with condensate in high humidity areas VIN Important specifier notes: Where code allows, follow recommendation below. 1. Plug must be removed from John Guest fitting. 2. Route 3/8" drain tubing through knockout in back of docking station and insert fully into John Guest fitting connection at the rear of the machine chassis. Route other end of 3/8" drain tubing to drain. 3. Drain must slope 1 /4" inch per foot (6 mm per 30.4 cm). Self-contained 1010, 1410 series ice machir231 83, 23185 Form#7030 6 — Horizon Elite ice tube runs - specifier guidelines Long tube runs for RIDE remote ice delivery equipment Important specifier notes 1. 75' (22.9 m) maximum ice transport tube run. 2. Tubing routing bends must have a 6.00" 0 5.24 cm) radius or larger. support maximum straps 2' (60.9 cm) minimum of 6.00" 0 5.24 cm) turn/corner radius beverage dispenser 3. Dips and traps are not allowed. If not supported from underneath, secure insulated ice transport tube at least every 2' (60.9 cm) to prevent drips and traps. 4. Relative humidity levels above 80% transport tube slope / ice transport tube — (toward ice machine) wall -mounted 1 3/16" OD, ice machine 2 1 /8" OD with insulation 1 /4" in areas where the ice machine or ice transport tube is located may produce excessive condensation that will cause water damage. 1' 5. Contact factory for recommendations (2 cm per meter) on running tubing through a decorative soffit or chase. Ice production — Horizon Elite 1010 series, 60 Hz, air-cooled models Inlet water Ambient air temperature F (C) temperature F (C) 60 (16) 70 (21) 80 (27) 90 (32) 100 (38) t 50 (10) 1160 (526) 1061 (481) 962 (436) 825 (374) 688 (312) n� C 60 (16) 1093 (496) 1001 (454) 909 (412) 795 (361) 681 (309) o 70 (21) 1026 (465) 941 (427) 857 (389) 765 (347) 674 (306) V 6 0 80 (27) 971 (440) 893 (405) 815 (370) 730 (331) 644 (292) m Y 90 (32) 917 (416) 941 (427) 773 (350) 694 (315) 614 (279) rrrrrrrrrrrr � Ice production —All Horizon Elite 1010 series, water-cooled models Potable water Condenser water temperature F (C) temperature 60 (16) 70 (21) 80 (27) 90 (32) 100 (38) F (C) r 50 (10) 1096 (498) 1043 (473) 1001 (454) 947 (430) 892 (405) a ^� c 60 (16) 1006 (457) 970 (440) 938 (426) 888 (403) 839 (381) o 70 (21) 917 (416) 898 (408) 874 (396) 830 (377) 786 (357) o 2 80 (27) 874 (397) 826 (375) 826 (375) 787 (357) 749 (340) rn Y 90 (32) 831 (377) 1 778 (353) 1 778 (353) 1 745 (338) 712 (323) 1 � Ice production —AII Horizon Elite 1410 series, air-cooled models Inlet water Ambient air temperature F (C) temperature F (C) 60 (16) 70 (21) 80 (27) 90 (32) 100 (38) L 50(10) 1593(723) 1466(665) 1339(607) 1230(558) 1121(508) ^� C 60(16) 1518(689) 1396(633) 1275(579) 1163(528) 1052(478) o v 70(21) 1442(654) 1327(602) 1211(549) 1097(498) 982(446) o 80(27) 1394(632) 1272(577) 1150(522) 1050(477) 950(431) a Y_ 90(32) 1345(610) 1327(602) 1089(494) 1004(456) 918(417) Ice production —All Horizon Elite 1410 series, water-cooled models Potable water Condenser water temperature F (C) temperature 60 (16) 70 (21) 80 (27) 90 (32) 100 (38) F (C) 50(10) 1436(652) 1411(641) 1385(607) 1370(622) 1354(615) v N c 60(16) 1417(643) 1367(633) 1318(621) 1307(593) 1296(588) o 70(21) 1397(634) 1324(602) 1251(568) 1245(565) 1238(562) o 2 80(27) 1318(598) 1253(577) 1189(540) 1170(531) 1151(522) Y 90(32) 1238(562) 1183(602) 1127(512) 1096(497) 1064(483) � Agion is a registered trademark of Sciessent LLC. HORIZON ELITE, ICE -DEVICE, ICE MANAGER, MICRO CHEWBLET, SAFECLEAN PLUS, SANISPONGE, SYMPHONY PLUS and VISION are trademarks of Follett Products, LLC. CHEWBLET, FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. Self-contained 1010, 1410 series ice machine 801 Church Lane I Easton, PA 18040, USA �OLLEIT 7030-202205 1 © Follett Products, LLC 23183, 231 5♦' 5-610.252.7301 1 follettice.com J Specification Ice storage capacity 50 lb (22.7 kg) Width 21.31 " (54.13 cm) Depth, upper cover 22.57" (57.33 cm) Depth, ice chute 18.85" (47.88 cm) Height 25.80" (65.53 cm) Service clearance 12.00" (30.50 cm) top 115V/60/1 electrical 4amps, 8' (2.4 m) cord, NEMA 5-15 450 Drain 3/4" MPT Utility connection location through bottom Minimum span —wall bracing required 16.00" (40.64 cm) on center in most applications NOTE: Wall mount bracket standard Approximate net weight 100 lb (45 kg) Approximate ship weight 118 lb (54 kg) NOTE: For indoor use only FOLLETT is a registered trademark of Follett Products, LLC, registered in the U5. Follett reserves the right to change specifications at anytime without obligation. Certifications may vary depending on country of origin. ID50 50 lb metered ice dispenser Dimensional drawing Front View I �21.31" (54.13 cn 25.80" (63.53 cm) Bottom View r 9.63" (24.46 c F 11.04" (28.04 cm <— 12.13" (30.81 cm Right Side View 18.85" (47.88 cm) 1.06" 1.50" t(2.69(m)y (3.81 cm) 9040-20230725 1 © Follett Products, LLC MSnu \ZVnu 801 Church Lane I Easton, PA 18040, USA .0 $ 800 523 9361 1 1 610.25273011 oll ttice.com 23421 ARYAK'AEIT ° Ice Manager Control Panel Ice Manager Control Panel Ice Manager Diverter Valve (1) Horizon Elite Chewbiet ice machine (purchased separately) r (2) Ice storage units a c (purchased separately or supplied by others) Any combination of bins or dispensers J Ice Manager"cliverter valve system IMDV-2 series Features: The Ice Manager diverter valve system automatically delivers ice from ONE Follett Horizon Elite'" ice machine to TWO separate dispensers or bins. The system includes a control panel, diverter valve, and components to connect two ice storage units chosen. RIDE® remote ice delivery equipment -deliver ice automatically through a tube to where you need it, instead of manually transporting - reduce handling to provide more sanitary ice and prevent safety issues for employees and customers - install ice machine and diverter valve up to 75' (22.8 m) away from the bin -create a more aesthetically appealing dining area with less heat and noise around your customers Flexibility with a wide choice of bins and dispensers - Follett ice storage bins, Ice Transport Systems (ITS), and Ice*DeVIce'" ice storage and dispensing systems - Follett Vision'" low -profile ice and beverage dispensers and Symphony Plus'M 1 10CM ice and water dispensers -countertop ice and beverage dispensers manufactured by others (see approved list on page 2) -other ice storage containers (contact factory) Efficient use of equipment -fill two bins or dispensers with only one ice machine - reduce the number of ice machines in your operation, or eliminate manual filling -keep one machine running more efficiently instead of two machines that may idle frequently -service and maintain only one machine instead of two Factory -arranged installation and start-up -turn-key system installation with factory -trained installers -full operational demonstration to end -user Warranty - 3 years parts and labor on all components Job Item Church Lane 1 Easton, PA 18USA 1.8 �OLLEIT .800.523.9361 11.610.252.73011 1 follettice.com 23424 Configuring the Ice Manager diverter valve system 1. Select Horizon Elite ice machine model Using the model configuration table below, determine the Horizon Elite ice machine that will best suit your needs. For more specifications on Horizon Elite ice machine models, see form# 7030, 7035, 8180 and 3311. Existing Horizon series ice machines may be retrofitted to integrate with the Ice Manager diverter valve system. Based on model# and serial#, determine the retrofit kit to order using the table below. Horizon Elite ice machine model: serial# (if existing Horizon ice machine): Horizon Elite 1010, 1410, 1810 and 2110 Series Ice Machine Model Number Configurations for use with Ice Manager Diverter Valve System HC C 1010 A M S Icemaker Voltage Series Condenser Application Configuration HC Horizon C 208-230/60/1 (icemaking head) 1010 A Air-cooled, self-contained M Ice Manager S RIDE Chewblet Self-contained only. 1410 W Water-cooled, self-contained (remote ice D 115/60/1 (icemaking head) 1810 R Air-cooled, remote condensing unit delivery equipment) Self-contained and remote. 2110 N Air-cooled, no condensing unit for If remote unit, high side is connection to parallel rack system 208-23016011. F 115/60/1 (icemaking head) Remote only. High side is 208-23016013. Select two dispensers or bins to be filled Choose two approved units for ice storage. If exact model is not known, note type of unit. Lane 1 is the primary lane and should be assigned to bin or dispenser with highest demand. Lane 1 Lane 2: If desired unit is not listed below, contact factory. Follett Ice Transport and Storage New Follett ice storage bin or transport system model. See form# 8590 for models. When ordering bin, specify bin top to be cut for Ice Manager diverter valve system. If ice machine will be top mounted on bin, see Step 3. Existing Follett ice storage bin or transport system model. Requires replacement top cut for Ice Manager diverter valve system. See form# 4025 for item numbers. If ice machine will be top mounted on bin, see Step 3. Follett Symphony Plus Ice and Water Dispenser 11 OCM Follett Vision Ice and Beverage Dispensers New Follett Vision 155 and 300 ice and beverage dispenser model. VU155N models are available via Special Quote Request (SQR). See form# 4025 for models. Order Vision with VUIMDVKIT to be configured for Ice Manager diverter valves stem. Existing Vision 155 serial# must be greaterthan B50001. Existing Vision 300 serial# must be greater than B50005. Ice and Beverage Dispensers' Coca-Cola Freestyle 90002 Lancer4500-22N Servend MD150 Coca-Cola Freestyle 70002,3 Lancer4500-30N Servend MD175 Coca-Cola Freestyle 91002.4 Lancer FS-16N Servend MD200 Cornelius ED/DF150 Series Lancer FS-22N Servend MD250 Cornelius ED/DF175 Series Lancer FS-30N Servend MDH302 Cornelius ED/DF200 Series Lancer FS-44N Servend MDH302 Cornelius ED/DF250 Series Lancer Sensation30"/44" Servend MDH402 Cornelius ED/DF300 Series Lancer Touchpoint Servend SV175 Cornelius IDC215 Lancer Bevariety Servend SV200 Cornelius IDC255/Pro/Fast Gate Pepsi Spire 3.0/5.0/4.11 Servend SV250 Cornelius Flavor Fusion/Overload Servend FRP-250 ' Consult with dispenser provider to be sure the dispenser is ready to dispense nugget ice. 2 Consult with Coca-Cola and Follett to qualify application prior to ordering. 3 Requires DVF30 top kit ordered separately from Follett and top adapter kit 46412 and ice kit 46430, which must be ordered from Coca-Cola. 4 Requires DVF26 top kit ordered separately from Follett. 5 Approved only for Pepsi Spire 3.0, 5.0 and 4.1 designed for top mount ice machines. Requires DVP22 top kit for 3.0 and DVP30 top kit for 5.0 and 4.1, ordered separately from Follett. For manual fill versions of Pepsi Spire 3 0 5 0 and 4 1 contact factory Horizon Series Retrofit Kits' Horizon Model # Item # 1000/1400/1650 after C43650 00191965 1000/140OA/W prior to C43650 00185181 1000/140OR/N prior to C43650 00185272 1010/1410/2110/1810 j 01116177 Extra transport tubing may be required to conned ice machine to diverter valve 3. Choose Horizon Elite series ice machine mounting option Mounting option: Wall Mount Bracket Item # HCD1010/1410and HCF1010/1410/2110 00997098 HCC1010and HCC1410 01085455 Machine Stand Item # HCC1010and HCC1410 01085463 HCD1010/1410/1810/2110 and HCF1010/1410/1810/2110 00997080 Follett Bin - Top Mount' New bin, see form# 8590 for models. When ordering bin, specify bin top to be cut for Ice Manager diverter valve system and ice machine'. Existing bin, see form# 4025 for bin top listing. Requires replacement top cut for Ice Manager diverter valve system and ice machine when ordering'. Other Specify what the Horizon series ice machine will be mounted on. ' See drawings on page 3 for min. bin width and required clearances. Form#3265 23424 Ice Manager diverter valve system Configuring the Ice Manager diverter valve system (Continued) 4. Evaluate site for location of equipment Lane 1 and Lane 2 dispensers or bins • Refer to dispenser or bin specifications for required clearances •See drawings below for required clearances for Ice Manager diverter valve system Follett Horizon Elite ice machine • 10' (3 m) maximum distance from Horizon Elite ice machine to diverter valve •See spec sheets 7030, 7035, 8180 and 3311 for utility requirements and dimensions Diverter valve •8' (2.4 m) maximum distance from diverter valve module to electric outlet 5. Determine length of ice transport tubes Lane 1: (approx. length): Lane 2: (approx. length): Use the following guidelines to determine length of the ice transport tube run from the diverter valve to each bin or dispenser. • Length of ice transport tube from diverter valve module to each dispenser or bin can be specified in 5' (1.5 m) increments from 10'-75'(3.0m-22.8m)' • Maximum vertical rise of ice transport tube —10' (3 m) • Horizontal run should be pitched so that melt water drains back to diverter valve module. Run must have 1/4" per foot pitch. • No dips or traps in the tube run • 75' (22.8 m) maximum distance from diverter valve to Lane land 1 Lengths to include any bends and turns needed to connect components. Lane 2 dispensers or bins 6. Site plan drawings •Drain required, 15' (4.6 m) drain tube provided Installation may be performed by an authorized installer Control panel contracted by Follett. Contact factory for details. •30' (9.2 m) max. distance from control panel to diverter valve Required clearances for Ice Manager diverter valve system Diverter valve ......• •• 12.00" (30.5 cm) Front View clearance lI mounting l�r•: 6.00" (15.24 cm) bracket 6.00" (15.24 cm) clearance clearance Sensor distribution unit (bins and ice and beverage dispensers only) Front View .................... T 12.00" (30.5 cm) cle a rance bin / dispenser top Side View bin / dispenser top Insulated transport tube (RIDE applications) Front View O 3.00" (7.62 cm) dia. hole required to run tubing through walls Side View Side View Top mount on a bin (minimum bin width) Front View sensor distribution unit min. 2.00" (5.08 cm) clearance a Y min. I. X - 10.50" (1.27 cm) clearance mululiu 4.12" (10.46 cm) Horizon Elite ice machine min. 1.00" (2.54 cm) O clearance bin top Note: For 30.00" (76.2 cm) Follett bin, sensor distribution unit may be placed behind ice machine. Ice Manager diverter valve system 23424 Form#32655 Specification Dimensional drawing Control panel W1 Width of control panel D1 Depth of control panel H1 Height of control panel Connections 12.00" (30.5 cm) 3.75" (9.52) 12.50" (31.8 cm) 30' (9.2 m) cable to diverter valve Diverter valve with mounting bracket W2 Width of diverter valve 13.62" (34.6 cm) D2 Depth of diverter valve 17.50" (44.4 cm) H2 Height of diverter valve 10.38" (26.4 cm) Connections 8' (2.4 m) cord and plug, 15' (4.6 m) drain tubing C1 Drain 3/8" NPT barbed drain fitting Lane 1 insulated ice transport tube and sensor cableto diverter valve', and connection kit for ice storage unit used' Lane 2 insulated ice transport tube and sensor cable to diverter valve*, and connection kit for ice storage unit used' Electrical 1.5 amps, 8' (2.4 m) cord, 115 V/60/1 NEMA 5-15 plug Sensor distribution unit W3 Width of distribution sensor 4.12" (10.46 cm) D3 Depth of distribution sensor 7.75" (19.68 cm) H3 Height of distribution sensor 3.50" (8.89 cm) General information Approximate ship weight of 120 lb (55 kg) Ice Manager with 50' (15.2 m) of ice transport tube Operating temperature 40 - 120 F (4 - 49 C), relative humidity not to exceed 55% t Lengths to be specified by customer. t Follett Vision ships with connection kit factory -installed (item# VUIMDVKIT). NOTE: For indoor use only SHORT FORM SPECIFICATION: Ice Manager diverter valve system to be model IMDV-2. System to direct ice delivery to two bins or dispensers automatically, utilizing sonic sensors to control level of ice. Ice machine to be Follett Horizon Elite model Lane 1 to fill Lane 2 to fill (ice and beverage dispenser, bin or Vision) Horizon Elite ice machine to be mounted on (bin, wall mount bracket or machine stand) System to include feet of insulated ice transport tube for Lane 1, and feet of insulated ice transport tube for Lane 2'. (75' (22.8 m) max. length for each lane) Horizon Elite ice machine and Ice Manager NSF, UL, and cUL listed. System to be installed by Follett. Lengths to be confirmed on -site prior to shipment. Lengths to include any bends and turns needed to connect components. Ice Manager diverter valve system Control panel Divertervalve with mounting bracket li�h■ M-1 �ap 16.00" (40.6 cm) —' Sensor distribution unit H3 HORIZON, HORIZON ELITE, ICE -DEVICE, ICE MANAGER, SYMPHONY PLUS and VISION are trademarks of Follett LLC. CHEWBLET, FOLLETT and RIDE are registered trademarks of Follett LLC, registered in the US. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. 234801 2 Church Lane 1 Easton, 2. 101 1 f, USA �OLLErr® 3265-201912 ©Follett LLC � �O 00.523.9361 1.610.252.7301 follettice.com Ice Manager"'diverter valve system MDV-2CM series Specification Dimensional drawing Control panel W1 Width of control panel 12.00" (30.5 cm) 131 Depth of control panel 3.75" (9.52) H1 Height of control panel 12.50" (31.8 cm) Connections 30' (9.2 m) cable to diverter valve Diverter valve with mounting bracket D2 Depth of diverter valve 14.50" (36.8 cm) W2 Overall width 19.82" (50.3 cm) W3 Width of bracket 16.00" (40.6 cm) H2 Height of diverter valve 14.15" (35.9 cm) Connections 8' (2.4 m) cord and plug, 15' (5 m) drain tubing Drain 3/8" NPT barbed drain fitting Lane 1 75' (23 m) ice transport tube, insulation and sensor cable to diverter valve, and connection kit for ID50 Lane 2 10' (3 m) ice transport tube, insulation and sensor cable to diverter valve, and connection kit for ice storage bin Horizon Elite'" ice machine tubing 10' (3 m) ice transport tube and (ships with ice machine) insulation to connect ice machine to dive rter valve Electrical 1.5 amps, 8' (2.4 m) cord, 115 V/60/1 NEMA 5-15 plug Sensor distribution unit W4 Width of distribution sensor 4.12" 00.46 cm) D3 Depth of distribution sensor 7.75" 0 9.68 cm) H3 Height of distribution sensor 3.50" (8.89 cm) General information Operating temperature 40 - 120 F (4 - 49 C), relative humidity not to exceed 55% Net weight of Ice Manager 26 lb (12 kg) Approximate ship weight of 170 lb (77 kg) Ice Manager with ice transport tube NOTE: For indoor use only Standard equipment includes Diverter valve and associated attachments — Manual — Brush —15' (5 m) drain tubing Control panel and associated attachments Lane 1 — 75' (23 m) ice transport tube, insulation, and sensor cable —Sensor distribution unit Lane 2 —10' (3 m) ice transport tube, insulation, and sensor cable —Sensor distribution unit 6" L— clearance Control panel Diverter valve with mounting bracket w2 Diverter valve required clearances �H 6" clearance Sensor distribution unit u I I'. \rir i i H: 6" clearance HORIZON ELITE and ICE MANAGER are trademarks of Follett Products, LLC. FOLLETT is a registered trademark of Follett Products, LLC, registered in the U5. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. 801 Church Lane I Easton, PA 18040, USA 1023-20230726 1 © Follett Products, LLC NSF Follett c L 1.800.523.9361 1 1.610.252.7301 1 follettice.corn YAKIKIfflAwy. 23423 Ice ManagerTMDiverter Valve System Installation Instructions Horizon Elite 1010, 1410, 1810 and 2110 Ice Machines HCC1010AMS, HCC1410AMS, HCC1010WMS, HCC1410WMS, HCD/HCF1010RMS, HCD/HCF1410RMS, HCD/HCF1810RMS, HCD/HCF2110RMS, HCD1010NMS, HCD1410NMS, HCD1810NMS, HCD2110NMS (See model number con figurator on page 2 for details.) Order parts online www.follettice.com (1) Horiz ChewbleY I .. ..... (purchased separately) Ice Manager Control Panel N (2) ice storage units (purchased separately) J m Any combination of bins or dispensers c J Fghammy ° 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 Innovative solutions, inspired by ice www.follettice.com 01113349 R01 23423 Chewblet® Ice Machine Model Number Configurations HC D 1810 A V S Icemaker Voltage Series Condenser Application Configuration MC MaestroTM C 208-230/60/1 (icemaking head) 425 up to A Air-cooled, self-contained V VisionT" S RIDE TM Chewblet® Self-contained only. 425 Ibs W Water-cooled, self-contained H Harmony— (RIDE remote (425 Series) D 115/60/1 (icemaking head) Self-contained and remote. If remote (193 k g) R Air-cooled, remote condensing unit B Ice storage bin ice delivery HC Horizon unit, high side is 208-23016011. 710 up to N Air-cooled, no condensing unit for J Drop -in equipment) Chewblet E 230/50/1 (icemaking head) 675 Ibs (306 kg) connection to parallel rack system M Ice Manager T To mount p' (710, 1010, Self-contained only. diverter valve 1410, 1810, F 115/60/1 (icemaking head) 1010 up to 1061 Ibs system 2110 Series) Remote only. High side is kg) P Cornelius Profile HIM Horizon 208-23016013. PR150 1410 up to up to Micro Chewblet 1466 Ibs (665 kg) 1810 up to 1790 Ibs (812 kg) 2110 up to 2039 Ibs (925 kg) Special tools required 3.50" (88.9 mm) hole saw: Required for ice and beverage dispensers manufactured by others or existing bins 2.50" (63.5 mm) hole saw: Required for drop -in dispensers 1.75" (44.5 mm) hole saw: Required for drop -in dispensers 2 Ice Manager Diverter Valve System Installation Instructions 23423 Ice Manager diverter valve system The Ice Manager diverter valve system delivers ice to two ice storage units enabling a single ice machine to meet demand for ice at two locations. The system's sensors monitor ice levels in each storage unit and automatically switch ice delivery to the appropriate location. Carefully review system overview (pages 4 & 5) and be sure that you have a copy of the Follett approved site survey before proceeding with installation steps. After thorough review of the site survey, install Horizon ice machine and dispenser/bin(s) using the installation guide provided with each unit. Read and complete installation sections 1 through 4. Diverter valve Lane 1 ice transport tube & sensor cable Control panel Lane 2 ice transport tube & sensor cable Read and complete installation sections below that apply to your specific application. Ice & beverage dispenser/bin lal dispenser Vision'M VU3OO ice & beverage dispenser 300 Ice Manager Diverter Valve System Installation Instructions 23423 3 Ice Manager - Site preparation and system overview 1010N/R 1810N/R 1410N/R 2110N/R 1010A/W 1410A/W 1650N/R ICE MACHINE Electrical - ice machine O • 1010 (A/W) 208-230/60/1, 11 A, max. ice machine fuse 15A • 1410 (A/W) 208-230/60/1,-5%/+10% under peak load. 16A, max. ice machine fuse 20A • 1010/1410/1810/2110 (R/N) Evap. 115/60/1, 6A; max. fuse 15A • 1650(R/N) Evap. 115/60/1, 6A; max. fuse 15A Condenser (R models only) 1010R 1410R 181OR 211OR Single 3-Phase Single 3-Phase Single 3-Phase Single 3-Phase Electrical 208-230V, 60 Hz Max Circuit 15A 15A 30A 25A 45A 25A 45A 30A HVACR Breaker Size Min Circuit 10.7A 9.9A 19.3A 14.2A 26.2A 15.7A 27.1 A 19.9A Ampacity ai NEMA 5-15 Electrical - Ice Manager • 115/60/1, 1.5 amps; max. fuse 15 amps Drains • Ice Manager - 3/8" (9.5mm) barb - 15 ft. (4.6m) 3/8" (9.5mm) I.D. tubing provided Potable water supply - ice machine • 10 - 70 psi (69 - 483kpa) • 45Fto90F(7Cto32C) • Follett recommends the use of an in -line water filter (item# 00130286) Condenser water supply for water- cooled systems O • 10 psi min.; 150 psi max. (69kpa min.; 1034kpa max.) • 45Fto90F(7Cto32C) • 1.5 gallons per minute (5.68 liters per minute) 4 Ice Manager Diverter Valve System Installation Instructions 23423 Temperature and humidity requirements • All components, including ice transport tube, must be operated in ambient temperatures between 40 F and 120 F (5 C and 49 C) • Relative humidity not to exceed 55% Ice transport tube requirements • Maximum vertical rise of 10' (3m) from ice machine to highest elevation of tube • Use one continuous piece of ice transport tube. Do not splice. • Horizontal run should be pitched so that melt water drains back to diverter valve. Ice transport tube run must have at least 1/4" per foot pitch (6.4mm/0.3m) • Secure ice transport tube as needed to eliminate dips and traps • Insulate all ice transport tube runs, making sure that sensor cable runs outside of the insulation 0 Ice transport tube and cable distance requirements • Ice machine to diverter valve - maximum run of 10' (3m) • Diverter valve to operator control panel - maximum run of 30' (9m) • Diverter valve to ice receptacle - maximum run of 75' (23m) • Distance between ice transport tube supports - maximum of 2' (0.6m) Operating temperature requirements • Ice Manager diverter valve system components, including ice transport tube must be operated in ambient temperatures between 40 F and 120 F (4.5 C and 49 C) Ice Manager Diverter Valve System Installation Instructions 23423 5 ODiverter valve Diverter Valve Required Clearances 0 .................................................... T 12" clearance 3 0 3 6" 6" 6" clearance clearance clearance from 0 tUF Mount diverter valve • Minimum side clearances of 6" (153mm) required 0 • Minimum top clearance of 12" (305mm) required 0 • Diverter valve bracket may be mounted on the floor © or on the wall © using (4) anchors capable of supporting min. 40 lb (18kg) • Diverter valve unit MUST face up 0 Diverter Valve Dimensions 13.625"� 17.468" 346mm 444mm <'= 10.375" 264mm O � a 16" 407mm %8�000 drain • Drain tube connects to fitting on underside of diverter valve 6 Ice Manager Diverter Valve System Installation Instructions 23423 ODiverter valve Connect diverter valve to ice machinet • Remove connection cover from diverter valve 0 • Connect blue ice machine cable to diverter valve Note: Control cable run not to exceed 10' (3m). • Connect blue ice machine control cable to ice machine • Connect power cord to diverter valve 0 • Run insulated ice transport tube to diverter valve © using guidelines in "Site Preparation - Overview" on pages 4 & 5. Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers 0 before making connection to ease assembly and prevent stainless coupler edge from cutting inner wall of tube. Note: Ice transport tube run not to exceed 10' (3m). t If Horizon ice machine is an existing unit install applicable retrofit kit before completing this portion of installation (retrofit instructions are included with retrofit kit). Ice Manager Diverter Valve System Installation Instructions 7 23423 © Control panel Mount control panel Remove cover from control panel 0 • Mount panel to wall © using wall anchors if needed [%1-7 OW Connect control panel to diverter valve • Connect gray control panel cable to control panel • Connect gray control panel cable to diverter valve 0 Note: Control panel cable run not to exceed 30' (9m). • Replace control panel cover 8 Ice Manager Diverter Valve System Installation Instructions 23423 0 Lane 1 Ice transport tube and sensor cable • Use the site survey to identify lane 1 dispenser or bin O • Measure ice transport tube run and sensor cable run from lane 1 dispenser/bin to diverter valve • Verify that run lengths comply with requirements on pages 4 & 5 • Insulate ice transport tube • Secure insulated ice transport tube and sensor cable as needed from dispenser/bin to diverter valve, being certain to prevent dips and traps from forming. See guidelines on pages 4 & 5. • Pitch tube at least 1/4" per foot (6.4mm/0.3m). Tube must drain towards diverter valve. • Connect lane 1 sensor cable 0 and insulated ice transport tube © to diverter valve • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers © before making connection to ease assembly • Visually inspect inside of plastic coupling for burrs and remove as needed • Hand -tighten cap nut on the coupling at diverter valve O Lane 2 Ice transport tube and sensor cable • Use the site survey to identify lane 2 dispenser or bin • Measure ice transport tube run and sensor cable run from lane 2 dispenser/bin to diverter valve • Verify that run lengths comply with requirements on pages 4 & 5 • Insulate ice transport tube • Secure insulated ice transport tube and sensor cable as needed from dispenser/bin to diverter valve, being certain to prevent dips and traps from forming • Pitch tube at least 1/4" per foot (6.4mm/0.3m). Tube must drain towards diverter valve. • Connect lane 2 sensor cable 0 and insulated ice transport tube © to diverter valve • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers © before making connection to ease assembly • Visually inspect inside of plastic coupling for burrs and remove as needed • Hand -tighten cap nut on the coupling at diverter valve r Hot Water 1160 F (71 C) 2 LANE 1 LANE 1 \LANE 2 Ice Manager Diverter Valve System Installation Instructions 9 23423 © Ice & beverage dispenser/bin 30" Lancer Sensation and Touchpoint w/IMDV 110CM Symphony Plus w/IMDV All other dispensers template 0 3-1/2" (88.9mm) dia. front of dispenser or bin top 5" (127 j(1 Freestyle 9000 Prepare ice & beverage dispenser/bin top • Using drawing above for your application, locate the proper location of ice & beverage dispenser (IBD) to place the supplied template 0 • Using supplied template and 3.5" dia. hole saw, cut holes per template Note: Use a hand saw or similar tool to complete the cut out. 27 mm) 02 mm) 1 zi ED300 dispenser only 4" (102mm) 0 o I 0 0 CL i i i 4" (102 mm) - _CD - o3.5" 03.5" hole saw hole saw i i i i R1 3/4' (19mm) 4" (102mm) 4" (102mm) REAR OF DISPENSER LID (UNDERSIDE) FRONT OF DISPENSER LID (UNDERSIDE) Mount sensor distribution unit • Unscrew cap nut and remove center assembly • Loosen screws and remove cover • Turn short arm of angle rods so unit can be lowered into hole of IBD top • Position unit into IBD top with tube at the front 0 • Turn angle rods to face outward • Tighten wing nuts until arms of both rods press firmly against underside of IBD top securing body of sensor distribution unit 10 Ice Manager Diverter Valve System Installation Instructions 23423 © Ice & beverage dispenser/bin Connect ice transport tube & sensor cable • Thread sensor cable through top of sensor distribution unit 0 • Connect sensor pigtail to sensor cable • Tuck cable inside sensor unit replace top and tighten screws • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers 0 before making connection to ease assembly and prevent stainless coupler edge from cutting inner wall of tube. • Connect insulated ice transport tube Ice Manager Diverter Valve System Installation Instructions 11 23423 0 Ice & beverage dispenser/bin Agitation adjustments - CORNELIUS O ON 0 OFF Cornelius models ED, DB, DF, IDC and Flavor Fusion Adjust the agitation timer located on the Cornelius PC board to 1 second on, 1 hour off. Note: See Cornelius manual for more information. Agitation adjustments - LANCER 4500 SERIES PRESS IN ON SWITCHES ROCKER PRESS IN ON THIS SIDE TO THIS SIDE TO TURN SWITCH (VIEW LOOKING TURN SWITCH OFF. DOWN) ON. Agitation adjustments - SERVEND SerVend models only No agitation adjustment required AGITATION TIME SWITCH NUMBER 3 a FX=ON 3 O O X X O =OFF 4 O X O X SWITCH ON SWITCH NUMBER SIDE VIEW 5 SWITCH OFF � 6 7 8 SIDE VIEW AGITATION FREQUENCY Lancer 4500 series only Adjust the agitation time to 1 second, and the agitation frequency to 150 minutes. Note: See Lancer manual for more information. phi 12 Ice Manager Diverter Valve System Installation Instructions 23423 © Ice & beverage dispenser/bin Y, Agitation adjustments — LANCER FS SERIES Initialization Screen (Boot Up Only) Lancer FS-16 Ver. 0.200 0 Main Menu Sub-Catagory FS-16 Setup Brands Per Side O Major/Minor VA L:2 R:1 FS-16 Setup Bonus Key Setup O O Config Bonus Key VA T:F M:S B:W FS-16 Setup Soda/Plain Water Cancel Enter Soda/Plain Water V:2 1:S 2:W 3:S 4:W �❑ FS-16 Setup Dispense Delay Config Dispense Only VA B1 DLY1 II Scrolls through Main Menu FS-16 Setup Set PC Mode Menu Press "Enter" to enter sub-catagory PC Mode Off On � Moves curser to right or left FS-16 Setup On Time (MSEC) PC Time 05000 1 Changes value (number/letter) 1 FS-16 Setup OFF Time (MIN) Press "Enter" to enter save changes Ice Stir Off 00150 Press "Cancel' to exit menu FS-16 Setup On Time (MSEC) Ice Stir On 01000 2nd Sub-Catagory FS-16 Setup Selection Sold Out Sold Out #1 Sold Out Sold Out #1 Off FS-16 Setup Upper Lower Sold Out #1 Carb Sensors 1000 500 V:1 13:1 FS-16 Setup Ice Bin Optic Ice Bin Sensors 1000 FS-16 Setup 12 0.104 0.104 Valve Code Version 34 0.104 0.104 FS-16 Setup 1 2 3 4 Number Of Valves On On On On FS-16 Setup Reload Defaults? Reset Defaults No Yes Lancer FS series only • Hold down "cancel' and "left button" to get to hidden menu 0 • Type in code 6655 • Type in 150 minutes "off time" and 1010 milliseconds (1 second of time) as the preferred setting Note: See Lancer manual for more information Ice Manager Diverter Valve System Installation Instructions 13 23423 © Ice & beverage dispenser/bin Dispenser diverter plate overview — CORNELIUS, ED, DF AND DB SERIES P/N 307277 — Diverter plate Single Agitator (single agitator Cornelius dispensers and left-hand dispense chute on dual -agitator 0 Cornelius dispensers) P/N 307277 — Diverter plate (single agitator Cornelius Dual Agitator dispensers and left-hand dispense chute on dual -agitator Cornelius dispensers) n u P/N (right-hand is e Diverter plate 0 (right-hand dispense chute on dual -agitator dispensers) Cornelius ED, DF and DB series only These dispensers require the installation of an ice diverter at the dispenser opening. • Disassemble chute assembly • Discard factory restrictor plate 0 • Replace with alternate diverter plate © (supplied) 14 Ice Manager Diverter Valve System Installation Instructions 23423 © Ice & beverage dispenser/bin Restrictor plate adjustment — CORNELIUS IDC and FLAVOR FUSION r r r r -r r r r / i Cornelius IDC and Flavor Fusion These dispensers require adjustment of the restrictor plate. • Loosen four nuts on ice chute assembly 0 • Adjust restrictor plate to fully open position • Replace four nuts and tight to 50 in. lbs. (max.) Y, Ice Manager Diverter Valve System Installation Instructions 15 23423 OFollett Vision VU155 ice & beverage dispenser 155 Vision VU155 dispenser ice transport tube and sensor cables • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with pliers 0 before making connection to ease assembly and prevent stainless coupler edge from cutting inner wall of tube • Install ice transport tube fitting in one of four pre - drilled rear holes in VU155 dispenser Note: If threaded end extends into dispenser it must be cut flush to inner nut. • Attach ice transport tube to fitting 0. Cut transport tube to proper length and support the tube at least every 2 ft. (.6m) to avoid dips or traps that will result in standing water. • Connect sensor pigtail to sensor cable t If VU155 is an existing unit install retrofit kit part# 00185165 before completing this portion of installation (retrofit instructions included with retrofit kit). 16 Ice Manager Diverter Valve System Installation Instructions 23423 OFollett Vision VU300 ice & beverage dispenser Vision VU300 dispenser ice transport tube and sensor cables • Insert ice transport tube through one of the four pre -drilled holes in the VU300 dispenser. 0 Be sure to cut transport tube to proper length to avoid dips or traps. • Locate mounting tabs • Using a 3/16" bit, drill through the ice tube 1" (26mm) from end of ice transport tube creating two holes E 00 151 • Slightly compress end of tube to engage holes in mounting tabs 0 • Connect sensor cable t If VU300 is an existing unit install retrofit kit part# 00185173 before completing this portion of installation (retrofit instructions included with retrofit kit). Ice Manager Diverter Valve System Installation Instructions 23423 17 0 Ice level set points Ice level set points are set at the factory and normally do not need to be changed. Setting recommendations are shown in the table below. Please contact Follett Technical Services toll free at (877) 612-5086 or +1 (610) 252-7301 prior to changing ice level set points. Factory settings LANE Full 10" Min 14" 1 Dif 3" LANE Full 10" 2 Dif 3" To view ice levels 1. Locate LCD screen on Ice Manager control panel. Initial screen will show ice levels for lane 1 and lane 2 and diverter valve status (Fig. 1). To view set points Press and hold both MODE SELECT and LANE 1 buttons until LANE 1 SETUP appears on the display (Fig. 2). Note: Default/factory-set ice level sensor settings are shown. 2. To view Lane 2, press MODE SELECT to navigate to lane 2 setup (Fig. 3). To change set points 1. Press and hold both MODE SELECT and LANE 1 buttons until LANE 1 SETUP appears on the display (Fig. 2). Note: Default/factory-set ice level sensor settings are shown. 2. Press LANE 1 button to move through FULL, MIN and DIF ice level sensor settings. When selected, choice will flash (Fig. 4). 3. Press MODE SELECT button to change ice level sensor set point (Fig. 5). 4. Press LANE 1 button to increase ice level sensor set point and LANE 2 to decrease ice level sensor set point, (Fig. 6) to correspond to the drop -in dispenser ice level sensor settings listed in table above. 5. Press MODE SELECT to save new ice level sensor setting (Fig. 7). 6. Press LANE 1 to continue to navigate through and set the Full, Min, and Dif ice level sensor settings for lane 1 (Fig. 8). 7. Press MODE SELECT to navigate to lane 2 setup (Fig. 9) 8. Repeat steps 2 through 6 to complete changes to lane 2 ice level sensor settings. Fig. 1 n Sensor Reading: Lane 1: Lane 2: " Status . OK Fig. 2 Lane 1 Setup: Mode Lane 1� Full: 10.0" select Min: 14.0" Dif: 3.0" Lane 20 Fig. 3 Lane 2 Setup: Mode Lane 1 O Full: 10.0" select Dif: 3.0" Lane 2 O Fig. 4 Lane 1 Setup: Mode Lane 1� Full: \ 10.0" select Min: 14.0" O Lane2O Dif: 3.0" Fig. 5 Lane 1 Setup: Mode Lane 1 O Full: 10.0"\ select Min: 10.0" Dif: 9.01, Lane 2 0 Fig. 6 Lane 1 Setup: Mode Lane 1 select O Full: 10.0" Lane 1/2 Scroll O Mode: Save Value Lane 20 Fig. 7 Lane 1 Setup: Mode Lane 1 O Full: 10.0" select Min: 10.0" Dif: 9.0.1 Lane 2 O Fig. 8 Lane 1 Setup: Mode Lane 1� Full: \ 10.011/ select Min: 14.0" O Lane 2 O Dif: 3.0" Fig. 9 Lane 2 Setup: Mode Lane 1 O Full: 10.0" select Dif: 3.0" Lane 2 O 18 Ice Manager Diverter Valve System Installation Instructions 23423 Before Operating Equipment Ice Manager Diverter Valve System must be cleaned and sanitized. Note: Do not use bleach to sanitize or clean the ice machine or diverter valve. '� WARNING • Wear rubber gloves and safety goggles (and/or face shield) when handling ice machine cleaner or sanitizer. 0 CAUTION • Use only Follett approved SafeCLEAN PIusTM (item# 01050863) and NU-CALGON IM-III Sanitizer. • Do not mix SafeCLEAN PIusTm and NU-CALGON IM-II solutions together • DO NOT USE BLEACH • It is a violation of Federal law to use these solutions in a manner inconsistent with their labeling • Read and understand all labels printed on packaging before use Note: Complete procedure for cleaning an sanitizing MUST be followed. Ice must be collected for 10 minutes from each lane before putting ice machine and Ice Manager back into service. Fig. 1 1. Press the CLEAN button. The machine will drain. The auger will run for a short time and then stop. Wait for the LOW WATER light to come on. Ice Manager Diverter Valve System Installation Instructions 23423 19 Fig. 2 2. Mix 1 gal. (3.8L) 120 F (49 C) water and one 7 oz. (198 g) packet of Follett SafeClean Plus (P/N 01050863). 3. Using a 1 quart (1 L) container, slowly fill cleaning cup until CLEANER FULL light comes on. Do not overfill. 4. Place one Sani-SpongeTM in remaining sanitizing and cleaning solution and retain for Step 39. Note: Do not use bleach to sanitize or clean the icemaker. 5. Replace cover on cleaner cup. Machine will clean, then flush 3 times in approximately 15 minutes. Wait until machine restarts. Fig. 4 6. Press power switch OFF. :5: 20 Ice Manager Diverter Valve System Installation Instructions 23423 Fig. 5 7. Locate Ice Manager control panel. Lane 1 O Mode ON O select Full o Icemaker OON O Min O Auto Manual 7 O O Full O Lane 2 O ON O 8. To sanitize Lanes 1 and 2, diverter valve must be in manual mode. Press the MODE SELECT button on the Ice Manager control panel. Manual light will come on. If auto light comes on, press MODE SELECT button again. 9. To sanitize Lane 1 — Press LANE 1 button. Lane 1 light will come on. Fig. 6 Fig. 7 Fig. 8 Mode select Icemaker ON O Auto Manual O '0 Lane 1 ON Q '00* Lane 2 ON O 0 Ice Manager Diverter Valve System Installation Instructions 21 23423 10. Disconnect ice transport tubes from diverter valve unit. Be sure to note Lane 1 (Fig. 8.1), Lane 2 (Fig. 8.2) and inlet (Fig. 8.3) ice transport tube connections to avoid confusion when reattaching. Fig. 9 11. Mix 1 gallon 120 F (49 C) water and 1.6 oz (48 ml) NU-CALGON IMS-III SANITIZER. Note: Do not use bleach to sanitize or clean the diverter valve. 12. Soak supplied brush in sanitizer solution and scrub inside of the diverter valve Lane 1 for at least 60 s, re -wetting the brush with sanitizer as needed. Fig. 10 13. Re -wet brush with sanitizer and scrub diverter valve inlet for at least 60 s, re -wetting the brush with sanitizer as needed. 22 Ice Manager Diverter Valve System Installation Instructions 23423 Fig. 11 14. To sanitize Lane 2 — Press LANE 2 button. Lane 2 light will come on. Fig. 12 15. Soak supplied brush in sanitizer solution and scrub inside of the diverter valve Lane 2 for at least 60 s, re -wetting the brush with sanitizer as needed. Fig. 13 16. Re -wet brush with sanitizer and scrub inlet for at least 60 seconds, re -wetting the brush with sanitizer as needed. Note: Inlet must be scrubbed with both Lane 1 and Lane 2 settings to be sure each lane is cleaned and sanitized. Lane 1 0 ON Q Lane 2 ON Ice Manager Diverter Valve System Installation Instructions 23423 23 Fig. 14 17. Rinse brush in potable, 120 F (49 C) water. Rinse Lane 1 (Fig. 14.1), Lane 2 (Fig. 14.2), and inlet (Fig. 14.3) with clean potable water for at least 60 s to be sure each lane is rinsed thoroughly. Fig. 15 18. Re -connect ice transport tube to Lane 1 (Fig. 15.1), Lane 2, (Fig. 15.2) and inlet (Fig. 15.3). Fig. 16 19. To sanitize Lane 1 ice transport tube — Press ice machine power switch OFF. 24 Ice Manager Diverter Valve System Installation Instructions 23423 Fig. 17 20. Verify that Ice Manager is in manual mode. Manual light should be on. If auto light is on, press MODE SELECT button to switch to manual mode. Fig. 18 21. Press LANE 1 button. Lane 1 light will come on. Fig. 19 22. Disconnect coupling from ice machine as shown. Mode select Icemaker ON Q 00 Auto Manual O O Lane 1 ON ,0 '00* Lane 2 ON O 0 Ice Manager Diverter Valve System Installation Instructions 23423 25 Fig. 20 23. Using disposable food service grade gloves, insert dry Sani-Sponge. 24. Insert Sani-Sponge soaked in SafeClean Plus (from Step 4). 25. Push both Sani-Sponges down ice transport tube with supplied pusher tube. /40 jrs" 41 3 Fig. 21 26. Remove 16" (407 mm) pusher tube. Fig. 22 27. Reconnect coupling. Press ice machine power switch ON. Ice pushes Sani-Sponges through tube. 26 Ice Manager Diverter Valve System Installation Instructions 23423 Fig. 23 28. Place a sanitary (2 gallon or larger) container in bin or dispenser to collect Sani-Sponges and ice for 10 minutes. Collect 5.5 Ibs (3 kg) of ice from unit. Discard ice and Sani-Sponge. Fig. 24 29. To sanitize Lane 2 ice transport tube — Press ice machine power switch OFF. Fig. 25 30. Verify that Ice Manager is in manual mode. Manual light should be on. If auto light is on, press MODE SELECT button to switch to manual mode. Mode select Icemaker ON O Auto Manual O O Ice Manager Diverter Valve System Installation Instructions 23423 27 Fig. 26 31. Press LANE 2 button. Lane 2 light will come on. 32. Disconnect coupling from ice machine as shown. 33. Using disposable food service grade gloves, insert dry Sani-Sponge. 34. Insert Sani-Sponge soaked in SafeClean Plus (from Step 4). 35. Push both Sani-Sponges down ice transport tube with supplied pusher tube. Lane 1 ON Q 0 �4 Lane 2 ON Q Fig. 27 Fig. 28 /sr0 (01jrs" 3 28 Ice Manager Diverter Valve System Installation Instructions 23423 Fig. 29 36. Remove and discard 16" (407 mm) pusher tube. 37. Reconnect coupling. Press ice machine power switch ON. Ice pushes Sani-Sponges through tube. 38. Place a sanitary (2 gallon or larger) container in bin or dispenser to collect Sani-Sponges and ice for 10 minutes. Collect 5.5 Ibs (3 kg) of ice from unit. Discard ice and Sani-Sponges. 39. Press MODE SELECT button on Ice Manager control panel to switch to auto mode. Auto light will come on. Fig. 30 M-,A Fig. 31 Fig. 32 Mode select Icemaker ON O .00* Auto Manual O O Ice Manager Diverter Valve System Installation Instructions 23423 29 30 Ice Manager Diverter Valve System Installation Instructions 23423 Ice Manager Diverter Valve System Installation Instructions 31 23423 Horizon, Horizon Elite, Ice Manager, SafeCLEAN, Sani-Sponge, RIDE and Vision are trademarks of Follett LLC. Follett and Chewblet are registered trademarks of Follett LLC, registered in the US. ANOLLEl 0 801 Church Lane •Easton, PA 18040, USA Toll free (877) 612-5086 • +1 (610) 252-7301 01113349R01 Innovative solutions, inspired by ice www.follettice.com 23423 © Follett LLC 6/17 Bin Tops for Ice Manager"m and Horizon EliteTM pedestal mount for Ice-O-Matic B55/B110 bin Bin top for Ice Manager with pedestal mount specification W1 Width 1311 Depth D2 Depth H1 Overall height of pedestal H2 Additional height added to bin after installation Net weight Approximate ship weight Bin top with pedestal mount Model configurations — Bin top for Ice Manager with pedestal mount Number of Description ice machines Bin Width Item number Bin top for Ice Manager with pedestal mount for Follett 1 B55 30" B55H22H30DV Horizon Elite on Ice-O-Matic DID 23525 B55 bin Bin top for Ice Manager with pedestal mount for Follett 1 B110 48" B110H22H30DV Horizon Elite on Ice-O-Matic DID 23526 B110 bin HORIZON ELITE and ICE MANAGER are trademarks of Follett Products, U.C. FOLLETT and RIDE are registered trademarks of Follett Products, LLC, registered in the US. Follett reserves the right to change specifications at any time without obligation. Certifications may vary depending on country of origin. B55H22H30DV — 30.02" (76.3 cm) B110H22H30DV-48.02" (122.0 cm) 21.29" (54.1 cm) 24.48" (62.2 cm) 9.91 " (25.2 cm) 8.70" (22.10 cm) B55H22H30DV-45 lb (20 kg) B110H22H30DV-56lb (25 kg) B55H22H30DV-47 lb (21 kg) B110H22H30DV-58lb (26 kg) 801 Church Lane I Easton, PA 18040, USA 1031-20230726 1 © Follett Products, LLC NSF 1.800.523.9361 1 1.610.252.7301 1 follettice.com ArdwyAKAKAFIV 23525, 23526 Ice Machine Pedestal for �OLLEIT ° . Ice-O-Mat�c Bin Installation Instructions The followinq parts are shipped with the bin top: Part # Description Qty 01541747 Pedestal End 2 201937 Screw, Cap, Hex Hd, 1/4-20 X 3/4" 4 01541721 Cover Plate (for use with 22" wide ice machines only) 1 01541689 Stiffener, Pedestal 1 01541614 Stiffener, Pedestal 1 207332 Bolt, Carriage, 1/4-20 X 1/2" Lg 16 200875 Washer, Lock, 1/4" 20 201004 Nut, Acorn, 1/4-20 16 01541630 or 01541648 Bin Top, 48" or 30" 1 Part # Description Qty 01541606 Channel, Pedestal 2 01478700 Screw, 10-32 x 1/2" Lg 6 200864 Nut, Hex, 1/4-20 4 200874 Washer, Flat, 1/4", 5/8" OD 4 206796 Thumbscrew, #8 x 1/2" 2 205561 Washer, Flat, 9/32" ID, use with Thumbscrew 2 202123 Sealant, 4.7 oz tube 1 207801 Gasket, 60 in. 1 The ice machine pedestal is adjustable and can accommodate both a 30" and 48" wide bin. The pedestal is also adjustable to accommodate a variety of Follett Horizon Elite ice machines. As an example, and for reference, the figure below shows the pedestal assembled to fit a 48" wide bin and a Horizon Elite 22"-wide ice machine. To adjust the pedestal to fit a 30" wide bin, the Pedestal Ends are attached to the Pedestal Channels using the inner -most holes of the Pedestal Channel. To accommodate a different Horizon Elite ice machine, the stiffeners are simply reoriented and placed in the appropriate location. o Pedestal End Pedestal Stiffener ° Stiffener Channel r Cover o Plate' o® Hex head screw, o 1/4-20 x 3/4", O o flat washer, lock o 00 washer, hex nut o , O o � 0 o Bin Top O o Pedestal Channel 0 Pedestal End Carriage bolt, 1/4-20 x 1/2", lock washer, acorn nut Screw, 10-32 x 1/2"' Cover Plate used only with this 22"-wide ice machine docking station. 801 Church Lane • Easton, PA 18040, USA �OLLEi° Toll free (877) 612-5086 • +1 (610) 252-7301 www.follettice.com 23525, 23526 01541986R02 © Follett Products, LLC 2/23 Procedure 1. Ensure that the bin top is removed from the bin. 2. Place Pedestal Ends on flat surface (floor), and turn them upside down. 3. Place the Pedestal Channels inside the Pedestal Ends. The slots in the Pedestal Channels and Pedestal Ends must align. 4. Using 16 1/4-20 x 1/2" carriage bolts and choosing the holes that accommodate the bin width, loosely hand -tighten the Ends to the Channels. Note: Do not tighten the bolts of the pedestal frame until the pedestal is correctly mounted on the ice bin. 5. Mount the pedestal on top of the bin gasket. 6. Align pedestal with rear wall of bin. 7. Ensure that the bottom flange of the Pedestal Ends are snug against the bin wall. 8. Place the ice maker Stiffeners into the cutouts based upon the ice machine configuration. 9. Ensure that the Pedestal Ends are level, then fully tighten the 16 carriage bolts. Note: Pay attention to how the orientation of the Stiffeners differs depending on which type of ice machine is being mounted. 30" PEDESTAL WITH 22" REMOTE -CONDENSING ICE MACHINE - MUST USE COVE r 48" PEDESTAL WITH 22" REMOTE -CONDENSING ICE MACHINE - MUST USE 2 Ice Machine Pedestal for Ice-O-Matic Bin AOLLEIT" 23525, 23526 30" PEDESTAL WITH 30" SELF-CONTAINED ICE MACHINE - DO NOT USE COVER PLj r 48" PEDESTAL WITH 30" SELF-CONTAINED ICE MACHINE - DO NOT USE CC 10. For 22"-wide ice machine docking stations, place the Cover Plate (with the large hole towards the rear and offset to the left of the bin) over the Stiffeners and align the holes. 11. Using the instructions shipped with the ice machine: ■ Mount the docking station to the rails (and Cover Plate, if applicable) and bolt in place. ■ Mount the ice machine to the docking station ensuring the drain tube is fully seated on the drain barb connection. ■ Install the drain and auxiliary chassis drain. ■ Make the electrical and potable water connections. AROLLETI 23525, 23526 Ice Machine Pedestal for Ice-O-Matic Bin 3 12. Once the ice machine installation is complete, locate the three holes on the left side, and three holes on right side of the pedestal flange. 13. Install mounting hardware to secure the pedestal to the bin side wall. ■ Use a 5/32" drill bit with a 1/4" drill stop installed to create pilot holes. Do not drill through interior bin wall. ■ Install (6) #10-32 x 1/2" screws. 14. Remove the existing gasket from the top front of the bin. 15. Slide bin top under pedestal and into place, ensuring that the rear flange is over the rear of the bin. 16. Pull bin top forward until the rear flange is tight against the rear of the bin. 17. Using a pencil or marker, trace the front edge and side edge of the bin lid to mark where the new gasket will be placed. 0 a° 0 ° o a 18. Remove the bin lid and apply the new gasket so that the bin lid front and sides will rest on the gasket. 19. Use the included sealant to seal all gasket joints and ends. 20. Reinstall the bin top and secure the rear of the bin top with the two thumbscrews and 9/32" ID washers. 21. Ensure there are no gaps where the bin top meets the gasket. 22. Using the instructions shipped with the ice machine: ■ Mount the shuttle actuator to the bin top. ■ Install the ice transport tube onto the shuttle actuator. 4 Ice Machine Pedestal for Ice-O-Matic Bin fOLLEIT" 23525, 23526 23. Per NSF, seal all seams of the frame using the sealant provided. Ensure sealant has a smooth finish. ■ All bolt heads and their oblong slots. ■ All seams (in entirety) where Pedestal Ends meet the Pedestal Channels. ■ All seams (in entirety) where Stiffeners meet the Pedestal Ends and/or Pedestal Channels. ■ All seams (in entirety) where Pedestal Ends meet the bin, both front and back (rear). ■ All seams (in entirety) where Cover Plate meets Stiffeners and Pedestal Channels (if applicable). AVOLLETI 23525, 23526 Ice Machine Pedestal for Ice-O-Matic Bin 5 Cleaning and Sanitizing Procedure Ice Machine Refer to the instructions shipped with the ice machine. Bin Top The top side of the bin top can be cleaned with a stainless steel cleaner such as 3M* Stainless Steel Cleaner & Polish or equivalent. * 3M is a registered trademark of 3M Company in the US and other countries. The underside of the bin top should be sanitized using a clean cloth and the same solution used to sanitize the ice machine. Pedestal The pedestal, underside of ice machine and/or Cover Plate should be cleaned and sanitized prior to use and periodically with any cleaning and sanitizing products suitable for use in a food zone.. Removing the Bin Top for Maintenance or Cleaning 1. Turn off the ice machine. 2. Reach in through the bin door and unscrew the large nut holding the shuttle actuator. 3. From above, pull the shuttle actuator out of the bin lid. 4. Unscrew the thumbscrews at the back of the bin top. 5. Lift up on the front of the bin top, then raise the back of the bin top as well. 6. Carefully slide the bin top out from underneath the pedestal. 6 Ice Machine Pedestal for Ice-O-Matic Bin few ssmy" 23525, 23526 dyson oirblcade V 10179 io LOW VOLTAGE AND HIGH VOLTAGE TECHNICAL SPECIFICATION Electrical Input voltage: Low voltage = 110-127 V, High voltage = 200-240 V Frequency: 50 or 60 Hz, subject to voltage (85-115 V at 50 Hz); (85-130 V at 60 Hz); (200-240 V at 50 & 60 Hz) Standby power consumption: Less then 0.5 W Motor specification: 1,000 W digital brushless motor Motor switching rate: 5,000 per second Amp: Recommended dedicated 15 amp circuit. (110V --10A; 120V---8.33A; 220V—4.55A; 240V--4.17A) Heater type: None Construction Fascia: Polycarbonate Antibacterial coating type: HUO2 (Sprayed Nickel) contains antibacterial additive in paint. HUO2 (White) contains antibacterial moulded additive. Can help prevent the growth of bacteria. Back plate mounting bracket: ABS/PBT Plastic Exterior screw type: Anti -tamper 4 mm Pin -Hex Water ingress protection to IP24 Filter HEPA filter (Glass fiber and fleece prelayer) Removes 99.97% of bacteria as small as 0.3 microns Operation Touch free capacitive sensor activation Hand dry time measurement: 12 seconds (Measurement based on NSF Protocol P.335) Sound power level: 79 dB(A) Sound pressure level @ 2 m: 63 dB(A)t Operation lock -out period: 30 seconds Airspeed at aperture: 675 km/h / 420 mph Maximum altitude: 2,000 metres / 6,561 ft. Operating airflow: up to 5.28 gal/sec & up to 42.38 CFM Operating temperature range: 0°C-40"C / 32°F-104oF Logistics Single unit order code: Sprayed Nickel - Low voltage: 307174-01, High voltage: 307172-01 White - Low voltage: 307173-01, High voltage: 307171-01 Unit barcodes: Sprayed Nickel - Low voltage: 885609009933, High voltage: 885609009797 White - Low voltage: 885609009896, High voltage: 885609009179 Net weight: 2.9 kg / 6.17 Ibs Packaged weight: 4.0 kg / 8.81 Ibs Packaged dimensions: (H) 146 mm x (W) 454 mm x (D) 273 mm / (H) 5 3/4" x (W) 171/8" x (D) 10 3/4" Standard warranty 5 year parts and 5 year limited labor warranty Accreditations: Carbon Trust NSF International Quiet Mark Contributes to LEED certification ADA compliant UL Listed Product range (Select one) HUO2 Sprayed Nickel Part number/SKU 0 Low Voltage: 307174-01 0 High Voltage: 307172-01 HUO2 White Part number/SKU 0 Low Voltage: 307173-01 0 High Voltage: 307171-01 dyson CARBON TRUST LISTED REDUCING CO2 The Carbon label is a trademark of the Carbon Trust. The NSF logo is the registered trademark of NSF I nternatio no I. Quiet Mark is a registered trademark of the Noise Abatement Society. For further information, please contact Dyson:1-855-720-6169, www.dyson.com/airblade 'Sound pressure measured at 2 m distance, in a semi-anechoic chamber dyson airbladeV 10179 TECHNICAL SPECIFICATION HU REAR ELEVATION 91/4u 7 1/2u 5/8 M Fixing locations (4) M O Side electrical entry point Fixing locations (4) 1/4" Rear Side electrical electrical entry point entry point o' 7/8 \ 21/8.. a i i o 0 0 6 5/8 1 aw a S � o 0 o a Mc,- Mounting backplate shown s a above in Rear Elevation. Da) 0 Machine dimensions Height 151/2" Width 97/32" Depth 4" Minimum clearance 8"/16" clearance either side and 1 3/16" above machine. 0 0 O � _a a- ---------- 0 `o a- o 0 a— m 1 E O N a_ 0 M L Ln N u 0 V U N a) E 0 v SIDE ELEVATION 4" Machine fascia shown above in Side Elevation. All dimensions shown in inches (+/— 3/6 inch). Holes indicated in green are measured to the center of the hole. *Please look into local guidelines for ADA compliance. For further information, please contact Dyson:1-855-720-6169, ©2016 DYSON www.dyson.com/airblade aB� •cOFF��,r Starbucks Coffee Kent Seattle, WA www.starbucks.com COMBI-FOLD PAPER TOWEL DISPENSER BY GP PRO (GEORGIA-PACIFIC), BLACK, 1 DISPENSER This durable and versatile plastic folded paper towel dispenser holds up to 400 C-Fold, 600 multifold or one package of BigFold® towels to provide a cost-effective solution for washroom paper towel dispensing. This attractive, stylish black commercial paper towel dispenser complements any decor and the covered key -lock design protects against waste and pilferage while making refilling towels quick and easy. Description: The Combi-Fold Paper Towel Dispenser gives you all the options for cost-effective paper towel dispensing. This durable, versatile commercial paper towel dispenser holds up to 400 C-Fold, 600 Multifold or 1 package of BigFold® paper towels, giving you refilling choices while helping minimize the need for maintenance, thanks to its high capacity. It's designed for high -use areas, with durable plastic construction that's made to last. The covered key -lock design helps protect against waste and pilferage, while making refilling the dispenser quick and easy. Features & Benefits: » DURABLE PLASTIC CONSTRUCTION, ideal for high -traffic areas » HIGH -CAPACITY COMMERCIAL PAPER TOWEL DISPENSER holds up to 400 C-Fold, 600 multifold or one pack of BigFold® towels to help minimize run -outs ECONOMICAL & VERSATILE, dispenses M-, Z- or C-fold paper towels KEY LOCK helps reduce waste & pilferage COMPATIBLE with Pacific Blue Select TM (20389, 21000) & Pacific Blue BasicTM (20204, 23304) M-Fold, Pacific Blue Ultra TM (20885, 20887) Z-Fold & Pacific Blue Select TM (23000) C-Fold Paper Towels UNIT COMES WITH 1 KEY �P Georgia-Pacific Product Details Brand Owner Brand MFG Part# UP - UPC Each Per Ship Unit Items Per Each Case Total Dispenser (WxDxH) Buy Multiple Case Shipping Info Case GTIN Case Gross Wgt Case Net Wgt Case Dimensions (LxWxH) Case Volume Unit Shipping Info TI-Qty/Layer HI-Layers/Unit Unit Qty Unit Dimensions (LxWxH) 1111111111 GP Georgia-Pacific® 56650A 036500311117 1 Dispenser 0 1 Each x x 1 EA 10036500311114 3.500 LBS 3.000 LBS 15.938 x 12.438 x 6.250 0.717 CFT 9 16 144 47.813 x 37.313 x 100.000 111111111 37111 10977 CAAtcc Commercial Restroom Accessories A Division of Bobrick Technical Data Date: CONSTRUCTION: BASIN -MOUNTED SOAP DISPENSER WITH ALL-PURPOSE VALVE Project Name: 2-11/16" 68mm 1-7/8" 48mm DIA. 4" 102mm 3-3/8" F 86mm DIA. G-64LB �E Adjustable to Counter Thickness 4" 102mm Maximum 8-1/4" 210mm if Basin -mounted soap dispenser has polyethylene globe. Units are designed to be filled from the top for easy maintenance. 411 (102mm) long spout directs soap flow over sink. Exposed portions are chrome -plated brass to match the existing faucets. CAPACITY: 8-1/411 (210mm) globe - 32-fl oz. (0.9-L) OVERALL DIMENSIONS: Unit requires 111 (25mm) hole in the vanity or basin. MOUNTING: Mounting location for push button dispensers are 4411 (1118mm) maximum above the finish floor. ADA GUIDE: Push buttons and pistons should be operable with one hand and without tight grasping, pinching, or twisting of the wrist. Activation of soap valves should not require more than 5 pounds of force when unit is completely filled. Spout shall rotate 360' without damage to valve mechanism. NOTE: Soap dispenser shall dispense liquid lotion soaps, and synthetic detergents. Basin -Mounted Soap Dispenser with All -Purpose Valve shall be Model G-64LB of GAMCO Commercial Restroom Accessories, A Division of Bobrick, One Gamco Place, Durant, OK The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 819/10 Printed in U.S.A. The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. 0 2010 by Gamco Commercial Restroom Accessories, A Division of Bobrick. 21551 0, legrand' radi ant Furniture Power Centers �-= - Easily bring power and charging Features & Benefits • Meets Safety Standards. Models either have 2, 3 or 4 tamper - resistant receptacles to keep little fingers away from danger. • Fast Device Charging. Some models provide two USB charging ports (5V, 3.1A total) ensuring that all of your devices charge as quickly as possible. • Versatile. Compact, low profile design allows you to mount the unit in more places than ever before. • UL Spill Water Compliant. Passed UL 962A spill water test requirements so it can even be used in a horizontal surface such as a table top. • Beautiful. Available in three attractive radiant finishes, black, white and nickel, so you can match or complement any furniture style. Included bezel hides the mounting screws for a cleaner look. • Easy to Install. Mounts using screw clamps instead of wood screws, allowing you to mount the unit in more types of surfaces, even glass and stone. Installation is a snap: Cut the opening, insert the unit, tighten the clamps, snap on the bezel and plug it in. Compliance right where you need it RDZ, RDSZ, RDB, RDSB,RDZC, RDSZC, RDR The world today runs on mobile devices. In fact, the average person carries more than 3 devices on them at once. Keeping these mobile devices charged is critical to both personal and professional success. radiant Furniture Power Centers allow you to conveniently bring power and charging right to the spaces where people work and play, all in a compact, aesthetically pleasing package. Office lobbies, waiting rooms, cafeterias, restaurants/bars, Lecture halls, transportation hubs, guest rooms, etc. can benefit from the installation of radiant Furniture Power. • Lighting control option. RDSZ & RDSZC models have a push button switch that controls a rear outlet for connection and control of a sconce, table lamp or floor lamp. Switch is ADA compliant (Section 309.4 f, 2010 ADA Standards for Accessible Design). • Pass-thru plug. The pass-thru plug on the radiant Furniture Power Center allows you to connect the power center to any outlet, even one that is already being used. • FCC Compliance. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • ETL Listed. Listed to both US and Canadian safety standards. (RD4R not listed to Canadian safety standards.) cETLus Meets UL962A the standard for Furniture Power Distribution Units and CSA C22.2 No. 308, the standard for Cord Reels and Multi -Outlet Assemblies. All models passed the Spill Test for UL962A and are suitable for installation on horizontal surfaces. RD4R ETLus Listed. LG1800R2 — Updated January 2019 — For latest specs visit www.Legrand.us/radiant 21551 0, legranda TECHNICAL SPECIFICATIONS cETLus Listed to UL962A, the Standard for Furniture Power Distribution Units and CSA C22.2 No. 308, the standard for Cord Reels and Multi -Outlet Assemblies radiant° Furniture Power Centers L l-1 1- VU -- I OICU IJN, ,-, d, Cord Set 6' (1.83m) or 10' (3.05m), SJT 14/3 right angle 5-15P Pass-Thru Plug USB 5Vdc, 3.1A Shared _ MECHANICAL Mounting ENVIRONMENTAL Operating Temperature Storage Temperature Warranty One Year 21/2" (64mm) RDZ & RDZC 1/8" (3.2mm) 5 5/8" (143mm) (51 mm) 1 7/8" $8mm) Mounts in vertical or horizontal position Any material up to 3/4" (19mm) thick 0°C to 65°C (32°F to 149°F) -350C to 850C (-31 OF to 1850F) RDSZ & RDSZC 2 1/2" (64mm) E 7 1/8" (181 mm) 1/8" (3.2mm) (51 mm) 1 7/8" 18mm) LG1800R2 — Updated January 2019 — For latest specs visit www.Legrand.us/radiant 2 21551 0, legrand0 Ordering Information RDZBK RDZWH RDZNI RDZBK10 RDZN110 RDZWH10 RDSZBK RDSZWF RDSZNI RDSZBK10 RDSZN110 RDSZWH10 radiant° Furniture Power Centers Basic Power Unit (RDZxx) - Two (2) tamper -resistant (TR) receptacles and two (2) fast charging USB ports. 6' (1.83m) cord with pass-thru plug. Receptacles rated 15A, 125Vac. USB ports rated 5Vdc, 3.1A total. Overall dimensions 5 5/8" wide by 2 1/2" tall by 2 1/8" deep (143mm x 64mm.x.54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 5 1/4" wide by 2" high (133mm x 51mm). Available in black (RDZBK), white (RDZWH) and nickel (RDZNI). Basic Power Unit with 10' Cord (RDZxx10) - Same as Basic Power Unit with 10' (3.1 m) cord with pass-thru plug. Available in black (RDZBK10), nickel (RDZN110) and white (RDZWH10). Switching Power Unit (RDSZxx) - Two (2) tamper -resistant (TR) receptacles and two (2) fast charging USB ports. 6' (1.83m) cord with pass-thru plug. Also has ADA-compliant push-button switch on the front that controls a rear receptacle to allow lighting control of a customer supplied portable lamp. Rear receptacle provided on the end of an 8" (203mm) cord. Receptacles rated 15A, 125Vac. USB ports rated 5Vdc, 3.1 A total. Overall dimensions 7 1/8" wide by 2 1/2" tall by 2 1/8" deep (181mm x 64mm.x.54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 6 5/8" wide by 2" high (168mm x 51 mm). Available in black (RDSZBK), white (RDSZWH) and nickel (RDSZNI). Switching Power Unit with 10' Cord (RDZxx10) - Same as Switching Unit but with 10' (3.1 m) cord with pass-thru plug. Available in black (RDSZBK10), nickel (RDSZN110) and white (RDSZWH10). LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 21551 0, legrand° Ordering Information RDZCBK RDZCWH RDZCNI RDZCBK10 RDZCNI10 RDZCWH10 RDSZCBK RDSZCWH RDSZCNI RDSZCBK10 RDSZCNI10 RDSZCWH10 radiant° Furniture Power Centers Basic Power Unit (RDZCxx) — Two (2) tamper -resistant (TR) receptacles and two (2) fast charging USB ports. One USB A port and one USB C port. 6' (1.83m) cord with pass-thru plug. Receptacles rated 15A, 125Vac. USB ports rated 5Vdc, 3.1 A total. Overall dimensions 5 5/8" wide by 2 1/2" tall by 2 1/8" deep (143mm x 64mm.x.54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 5 1/4" wide by 2" high (133mm x 51 mm). Available in black (RDZCBK), white (RDZCWH) and nickel (RDZCNI). Basic Power Unit with 10' Cord (RDZCxx10) — Same as Basic Power Unit with 10' (3.1 m) cord with pass-thru plug. Available in black (RDZCBK10), nickel (RDZCN110) and white (RDZCWH10). Switching Power Unit (RDSZCxx) — Two (2) tamper -resistant (TR) receptacles and two (2) fast charging USB ports, one USB A port and one USB C port. 6' (1.83m) cord with pass-thru plug. Also has ADA-compliant push-button switch on the front that controls a rear receptacle to allow lighting control of a customer supplied portable lamp. Rear receptacle provided on the end of an 8" (203mm) cord. Receptacles rated 15A, 125Vac. USB ports rated 5Vdc, 3.1A total. Overall dimensions 7 1/8" wide by 2 1/2" tall by 2 1/8" deep (181 mm x 64mm x 54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 6 5/8" wide by 2" high (168mm x 51 mm). Available in black (RDSZCBK), white (RDSZCWH), and nickel (RDSZCNI). Switching Power Unit with 10' Cord (RDSZCxx10) — Same as Switching Unit but with 10' (3.1 m) cord with pass-thru plug. Available in black (RDSZBK10), nickel (RDSZCN110) and white (RDSZCWH10). LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 21551 0, legranda TECHNICAL SPECIFICATIONS cETLus Listed to UL962A, the Standard for Furniture Power Distribution Units and CSA C22.2 No. 308, the standard for Cord Reels and Multi -Outlet Assemblies RD4R ETLus Listed Performance ELECTRICAL Electrical Outlets rated 15A, 125Vac Cord Set 6' (1.83m) or 10' (3.05m), SJT 14/3 right angle 5-15P Pass-Thru Plug (RD4R SJT 12/3) MECHANICAL Mounting Mounts in vertical or horizontal position Any material up to 3/4" (19mm) thick ENVIRONMENTAL - Operating Temperature 0°C to 65°C (32°F to 149°F) - Storage Temperature -35°C to 85°C (-31°F to 185°F) Warranty One Year RD2R 21/2" e e (64mm) 1/8" (3.2mm) 4 9/16" (116mm) Y I/V (105mm) (51 mm) RD3R 2 1 /2" (64mm) radiant° Furniture Power Centers 5 5/8" (143mm) (130mm) 7/8" 1 7/8" Bmm) (48mm) 1/8" 2" (3.2mm) (51mm) LG1800R2 — Updated January 2019 — For latest specs visit www.legrand.us/radiant 5 21551 M, legrand° 2 1 /2" (64mm) RD4R 7 ii8.. (181 mm) 1 7/8" (48mm) 1/8" 2 "I (3.2mm) (51 mm) radiant° Furniture Power Centers LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 21551 0, legrand0 radiant° Furniture Power Centers Ordering Information RD2RBK Power Only Two Outlet Unit (RD2Rxx) - RD2RWH Two (2) tamper -resistant (TR) receptacles. 6' (1.83m) cord with pass-thru plug. RD2RN1 Receptacles rated 15A, 125Vac. Overall dimensions 4 9/16" wide by 2 1/2" tall by 2 1/8" deep (116mm x 64mm.x.54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 5 1/4" wide by 2" high (133mm x 51 mm). Available in black (RD2RBK), white (RD2RWH), and nickel (RD2RN1). RD2RBK10 oI o Power Only Two Outlet Unit with 10' Power Cord (RD2Rxx10) - RD2RWH10 Same as Power Only Unit but with 10' (3.1 m) cord with pass-thru plug. Available in RD2RN110 black (RD2RBK10), white (RD2RWH10) and nickel (RD2RN110). RD3RBK RD3RWH RD3RN1 RD3RBK10 RD3RWH10 RD3RN110 RD4RBK RD4RWH RD4RN1 RD4RBK10 RD4RWH10 RD4RN110 Power Only Three Outlet Unit (RD3Rxx) - Three (3) tamper -resistant (TR) receptacles. 6' (1.83m) cord with pass-thru plug. Receptacles rated 15A, 125Vac. Overall dimensions 5 3/4" wide by 2 1/2" tall by 2 1/8" deep (146mm x 64mm.x.54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 5 1/4" wide by 2" high (133mm x 51 mm). Available in black (RD3RBK), white (RD3RWH), and nickel (RD3RN1). Power Only Three Outlet Unit with 10' Power Cord (RD3Rxx10) - Same as Basic Power Unit but with 10' (3.1 m) cord with pass-thru plug. Available in black (RD3RBK10), white (RD3RWH10) and nickel (RD3RN110). Power Only Four Outlet Unit (RD4Rxx) - Four (4) tamper -resistant (TR) receptacles. 6' (1.83m) cord with pass-thru plug. Receptacles rated 15A, 125Vac. Overall dimensions 7 1/8" wide by 2 112" tall by 2 1/8" deep (181 mm x 64mm.x.54mm). Mounting flange is 1/8" (3.2mm) thick. Requires a hole cut of 5 1/4" wide by 2" high (133mm x 51 mm). Available in black (RD4RBK), white (RD4RWH), and nickel (RD4RN1). Power Only Four Outlet Unit with 10' Power Cord (RD4Rxx10) - Same as Basic Power Unit but with 10' (3.1 m) cord with pass-thru plug. Available in black (RD4RBK10), white (RD4RWH10) and nickel (RD4RN110). LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 21551 M, legrand° radiant° Furniture Power Centers Ordering Information RDB2BK Replacement Bezel for Power Only Two Outlet Unit (RDB2xx) - RDB2WH Overall dimensions 4 9/16" wide by 2 1/2" tall by 1/8" thick (116mm x 64mm x RDB2N1tZ 3.2mm). Available in black (RD13213K), white (RDB2WH) and nickel (RD1321\11). RDBBK Replacement Bezel for Basic Power Unit & Power Only Three Outlet Unit RDBWH (RDBxx) - Overall dimensions 5 5/8" wide by 2 1/2" tall by 1/8" thick (143mm RDBNI x 64mm x 3.2mm). Available in black (RDBBK), white (RDBWH) and nickel (RDBNI). RDSBBK Replacement Bezel for Switching Unit & Power Only Four Outlet Unit RDSBWH (RDSBxx) - Overall dimensions 7 1/8" wide by 2 1/2" tall by 1/8" deep (181mm RDSBNI11 x 64mm x 3.2mm). Available in black (RDSBBK), white (RDSBWH) and nickel (RDSBNI). LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 21551 M, legranda radiant° Furniture Power Centers LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 21551 M, legrand° radiant° Furniture Power Centers LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 10 21551 M, legranda radiant° Furniture Power Centers LG1800R2 — Updated January 2019 — For Latest specs visit www.legrand.us/radiant 11 21551 0, legrand° Complementary Devices & Accessories radiant® Collection L The radiant collection of switches, outlets and dimmers by Legrand puts that stylish finishing touch affordably within reach. Radiant gets rid of unsightly screws, delivering clean looks in a range of colors and metallic finishes. radiant° Furniture Power Centers adorne° Furniture Power Center Providing power, USB charging and lighting control in your high end furniture has never been easier. Just install the appropriate adorne Furniture Power Center in your furniture and plug in your light fixture. Perfect for headboards, night stands, desks, side tables, etc. Models are available to switch any cord connected lighting load. There are also models that will dim cord connected incandescent, halogen, CFULED and ELV fixtures, up to 45OW. adorne® Collection deQuorum'" Flip -Up Table Boxes The adorne collection by Legrand deQuorumTm Flip -Up Table Boxes bring combines the world's most innovative ready access to power and USB charging light switches and outlets with an array to work surfaces, desks, night stands and of stylish and custom finishes. any other horizontal surface. Horizontal surfaces are prone to spills from liquids. Recognizing that accidents often happen, deQuorum Flip -Up Table Boxes have been designed and rated specifically to perform in these areas. Vertical Markets • Retail • Hospitality • Commercial Office • Municipal NOTE: All brand and product names referenced in this document are registered trademarks or trademarks of their respective holders. A :NOTE: The paper used to print this document is an environmentally t responsible paper with 10 % post consumer waste, with FSC and SFI Chain of Custody certifications, Lacey Act complaint. 100 % of the electricity used to manufacture Flo sheets is generated with Green-e certified renewable energy. • Multi -Dwelling Units • Worship • Education • Transportation 0, legrand° Legrand, North America 60 Woodlawn Street West Hartford, CT 06110 1.877.BY.LEGRAND (295.3472) www.legrand.us Canada 905.738.9195 www.legrand.ca FOLLOW US 0 LG18OOR2 ©2019 Legrand AIL Rights Reserved W The Dyson A*IrbladeV hand dryer back panel This back panel has been designed by Dyson engineers to protect walls from water droplets in high traffic areas. Made from satin finish stainless steel, the back panel can be quickly installed directly to the wall with contact adhesives. Dimensions H: 3V/2" (800 mm) x W: 153/4" (400 mm) x D: V32" (0.5 mm) For rrnra information: 888-397-6622 airbladeinfo@dyson.com www.dyson.com dyson oirbladeV The hygienic hand dryer is 30%quieter.' 'Loudness reduction compared tothe original Dyson AirbladeV hand dryer. JOE TAP KIT SPEC -N 14 I I I 1 1 A "r� I to B t r-nrr P 21.59 -- --- - Q .�pb . 41mn Ndlu 6mrl�HN.q. µt 5.65 ntobiaf. MoclneO Lonlexx 5s.el O erbn�umEMM u�nNl etlpax rauMeE.fOB.xb Oe smooln r�M PM reMinmxn.rvM brertlgry muss b. •/-OlfSmm wmnaa ...0 r�i. :lo�l3 "x�s m.m KwiE. I.I wEIGM' Srvfn i Of i 2 rvorc. aa..E« cl.mp. 0,'� I RI9.33 2.00 I 4�E.e II � J _ 41.70 tt15•b'` Iwan,acr.•.�E.ba sonl.. s..l Eee.x,o�.—,N�ry ••�••... SCNE. � wFN'.1.: lal COMPONENTS: B A B A Joe Tap collars with 2 pieces/kit (set of 1 L + 1 R). Badge(1 pc CN+1 pc NCB)/kit & 2pcs wood handle DESIGN I 22627 M10W24r' (3004A ) 304 stainers steel size tolerance on saew(nut) 0.1mm twr.�RA1-11t 10L (0.1mm) 1)11gF /TOTIn insert saew(nut)vAth external thread Kc VITRO COLD DREW 1 JOE TAP KIT SPEC COMPONENTS: Joe Tap collars with 2 pieces/kit (set of 1 L + 1 R) Badge(1 pc CN+1 pc NCB)/kit 2pcs wood handle DESIGN ID 22627 STARBUCKS Back Bar Collar ,dk Phillips screwdriver IRV required for assembly 01 0C) o 0 0 a Screw (2x) O-ring (2x) Badge (2x) Handle (2x) Left Collar (1x) Right Collar (1x) 1 Remove 707 Right Left 0 O � O 0 0 Back Bar Collar - JoeTap DESIGN ID 22627 Completed Assembly Back BarCollar- JoeTap DESIGN ID 22627 \/VST966# 1 10416 * INDICATES FINISH CODE. SHELVES ONLY, POSTS ORDERED SEPARATELY. I 6-PACK OF 18X36 WIRESHELVES F; ORIGINAL REMOVE BIN MARKERS AND INSERTS 1 36' FRONT ELEVATION �SURELOCK ASSEMBLY 9 L1lLJ SYMBOL INDICATES POST NUMBER SURELOCK (PLASTIC SLEEVE) Example IS PLACED ON. --- SURELOCK (PLASTIC SLEEVE)— �- 5 9111111111111111 mom momillill `MrENL2P STORAGE PRODUCTS GROUP 112M hUfx92 Dr -le CON D CJ1 'G-1C P I i37-3830 F: )767-6 PROPRIETARY NOTICE: TN. ]P—CCRans Cn YIaOL pep e j .%.mom or c OfLb7,E PROOMM ! INTERhAT101YL 1.1C. My I>---e9 c4A:'.Peee aMb n[ Sao^ �_= U -ate Tereo/e�[ep Y. .iDo'Yr] b!ePO IMeTxCN LL: UgYreOmn: sneer an rea.e� cave a .B1p DTION BY Date EC ZC 5111105 8384 ZC 7101105 18, SIDE VIEW BILL OF MATERIALS ITEM QTY. PART# DESCRIPTION 1 6 1836* 18"X36" WIRESHELF weight Cube Description: 68 5.04 WIRE SHELVING 6—PACK 18X36 File Name: 103064—S01—A— Model// WST966* Date: Material Finish: 4125105 AS SPECIFIED Drawn By: Checked By: Size: Scale: Sheet: Rev: Sketch No. ZC JM A NTS 1 of 1 A 103064 Ltr I REVISION DESCRIPTION BY Date I ECO/NPR A ORIGINAL PP 5.21.04 B REVISED TEXT THROUGHOUT PW 10.21.04 SURELOCK ASSEMBLY s SYMDOL INDICATES POST NUMBER SURELOCK (PLASTIC SLEEVE) xamDle IS PLACED ON. @_A 7 SURELOCK (PLASTIC SLEEVE)+ 87" FRONT ELEVATION BILL OF MATERIALS - STBKP86Z4 ITEM QTY. PART NO. IDESCRIPTION 1 4 P86Z POST 86" ZINC N BACKROOM STORAGE E 6 86" POST KIT 4-PACK �a �� _ •(' Q �Rr1F�f' STBKP86Z4 CUSTOM WORKSTATIONS _____- =__ — -- — S H E L�/ I N G INTERNATIONAL STORAGE SYSTEMS 11230 Harland Drive Covington, Georgia 30209 PH: (770) 787-9830 FAX: (770) 787-6165 PROPRIETARY NOTICE: International Storage Systems, a division of Leggett & Platt, claims proprietary rights on the contents disclosed on this drawing and all processes, equipment, components, methods, or any other developments either directly or indirectly related to this project. This drawing is issued in confidence for engineering purposes only and may not be reproduced or used to manufacture anything shown hereon without direct 'written' authorization from International Storage Systems to the user. Tolerances: Unless otherwise Specified Description: 86" POST KIT 4—PACK BACKROOM STORAGE PN: STBKP86Z4 Decimals: / / XX +/— .02 Fractions: + — 1 32' .XXX + — .010 Angles: +/— 1/2' File Name: _S01_B— Date: Date: 5.21.04 Scale: NTS Material: Finish: Drawn By: PP Size: A Sheet: 1 of 1 Rev: B Drawing No. 102878 WST1878C DIMENSIONS IN ( ) ARE REFERENCE. DIMENSIONS IN [ l ARE MILLIMETERS, ALL OTHER DIMENSIONS ARE INCHES. UNDER SHELF CART KIT 181"X30" 104999_A01 22212 REVISIONS ZONE REV. I DESCRIPTION I BY I DATE ECO / NPR 01 1 RELEASED FOR CUSTOMER APPROVAL I SSI 2/12/2020 9518 (31.55[801]) (25.44 [646]) (19.37 [492] (19.13 [486]) 8 1 1 LU30* 30" UNIVERSAL SHELF LEDGE 102709_A01 7 2 LU18* 18" UNIVERSAL SHELF LEDGE 102709_A01 6 1 1836PSG 18"X36" SHELF GUARD OPAQUE 100251 P01 5 1 TF336* 3-SIDED FRAME, 18"X36" 102552_A01 4 1 1830FSW FSW SHELF, 18"X30" 100086 A01 3 4 CM3M 3" SWIVEL RUBBER CASTER 100810 A01 2 1 1830* 18"X30" ISS WIRE SHELF 101 151A01 1 4 P21 N* 21" ISS POST FOR CASTER (NO FOOT) 100113_A02 ITEM NO. QTY. PART NO. DESCRIPTION DWG. NO. BILL OF MATERIALS SURELOCK ASSEMBLY SYMBOL INDICATES PO&T NUMBER y suneux �vsnc sLCEve is EXAMPLE IACEOON 9 6 BUBELOOK _ 7 Irusnc slEErEI 6 CURRENT KETCHES\ :+ �� N %11121 STORAGE PRODUCTS GROUP Harland Drive Covinggton,ton, Georgia 30014 - PH: 1-800-810-9080 _tI www.spgusa.com PROPRIETARY NOTICE: This sheet contains confidential, proprietary information io al LLC Product Group International it Anypersonacceptingthis sheet and/or information agrees to make no disclosure, use or duplication thereof except as authorized Dy SPG to return this sheet on request. Copyright © 2010 Storage Product Group Internatonal. All rights reserved. weight: TBD lbs. volume: TBD CU f1. Data 2/ 12/2020 Drawn By: SSI Material: AS NOTED RD$n: AS SPECIFIED UNDER SHELF CART KIT 18"X30" TBD TBD I NONE WST1878C ke,ah Na.104999_S01 SHEET 1 of 1 Rev. 01 Supplier Item# 1481032 Supplied by: GLOBAL EQUIPMENT COMPANY INC Oracle ID 1481032 Supplier Contact: Leslie Wittenburg PH: (609)-737-6898 EMAIL: Wittenburg@globalindustrial.com Order in Compass - Use generic SKU Locker - 11106197 NON CATALOG INTERIOR FIXTURE Manufactured byf'� Storage Made Easy Materials: Doors, frames, and body parts shall be fabricated from prime quality, class one mild cold and hot rolled steel free from buckle, scale or other imperfections (A.S.T.M.-Al008). Finish: All steel components shall be thoroughly cleaned and phosphatized for rust resistance in a five - stage pre-treatment process. A high grade of polyester / epoxy powder paint is to be applied electrostatically with a gloss reading of between 55 and 65. The finish shall have a salt spray rating of 250 hours or more. Cleaning: The finish of Tennsco lockers is such that it can be cleaned with most household cleaners, including alcohol and ammonia. Industry standard testing determined that the finish of Tennsco lockers to chemical and acids was acceptable with no visual effect to 5 different solutions. These solutions were as follows: a 95% solution of Isopropyl Alcohol, a 10% solution of Acetic Acid machine oil, undiluted household ammonia, and a 10% solution of Lye. Cleaners should not be left on the units for more than 15 minutes before cleaning off. Abrasive cleaners should not be used. If they are used, over time the units will lose their gloss. Assembly: Locker is welded, ships assembled See page 2 for instructions for anchoring 1 1 �! Width (inch) 15" Depth (inch) 18" Height (inch) 66" Opening Width (inch) 15" Opening Depth (inch) 181, Opening Height (inch) 12" Weight: 67 LBS This is for the color Medium Grey, This locker is also available is Sand, Light Grey, Champagne/Putt and Black. *SCScertifiedN m INDOOR AIR QUALITY Indoor Advantage I Furniture GOLD ofComm Commerce CHAMBER of Commerce &Industry TFNNFS MP VWTNRE --ON TKO048 Instructions for Anchoring Tennsco Lockers Storage Made Easy For mounting lockers side to side, it is recommended to remove the second and fourth rivet from the top of the locker and the second rivet from the bottom of the locker. The rivets can be removed using a drill. The drill bit should be no more than a 3/16' diameter. Position the drill bit in the center of the rivet. The soft aluminum rivet will be easy to drill through. Once the rivets are removed, a nut and bolt can be used to attach the lockers side by side. # 8 or # 10 nuts and bolts are recommended. Some installers prefer drilling a new hole to mount the lockers side by side. If this is done, make sure that the drilled hole goes through both the frame and side. It is not recommended to use a screw to attach lockers side by side. The tip of the screw may cause damage to items stored in the locker. For mounting lockers back to back, it is recommended to drill mounting holes in the top corners of the openings. There is a 1" flange on the side panels that overlaps the back panel. The holes should be drilled through the back flange of the side. This area is reinforced and will prevent deformation of the locker. For anchoring lockers to a wall, mount a 1" x 4" or 1" x 6" wooden plank horizontally to the wall with the top of the plank 1" down from where the top of the locker will be. If the locker is 72" high, the top of the board should be 71" from the floor and if the locker is 78" high, the top of the board should be 77" from the floor. If required by local Fire Codes use FRT (Flame Retardant Treated) wood. Make sure that the board is attached to the wall with all of the attachments going into the wall studs or block wall. For Steel studs use a self -drilling #14-13 x 3" DP1 Pancake head sheet metal screw with a minimum pullout of 300 pounds in 20 gauge material for mounting the board through the drywall and into the steel studs. For wooden studs use a minimum #10 x 3" Wood Screw. For block walls use a minimum 3/16" x 3" Phillips Flat Head Tapcon Self7apping Concrete Anchor. The wallboard should run the entire length behind the lockers with attachments in every stud or block. Drill a hole through the back of each locker 3" to 4" from the top of the locker. The hole should be slightly larger than the hardware selected for anchoring the locker to the wall. Make sure that the hole corresponds to the center of the wallboard. Use a #10 x 3/4" Full Thread Pan Head Wood Screw with a washer and run it through the holes in the back of the locker and into the wallboards. All lockers must be attached in this way. It may be necessary to shim under the front legs of these lockers. For anchoring lockers to the floor, it is recommended that the installer contact the factory. There are many bases offered by Tennsco and several anchoring methods. TK0048 tennsco Storage Made Easy ADA Locker Guidlines Included are the ADA Guidelines as they apply to Tennsco Lockers: All of the lockers can be opened with less than the minimum allowable force required by the ADA guidelines. The doors can be opened without tight grasping, pinching or twisting of the wrist with no more than five pounds of force to open or operate the locker. This specific guideline is applied to people with fine motor skill problems. The guideline is applied to people with fine motor skill problems. The guideline is applied to people with fine motor skill problems. The guideline that applies to wheelchair access indicates that anything below 9" and above 54" is not wheelchair accessible. ADA Compliant Lock: Tennsco's ADAKC Key Cap will make any master lock sold by Tennsco (that uses a key) ADA compliant. Design increases the size of the key head to make it easier to grip and turn. It can be used on all Tennsco Single, Double and Triple Tier lockers, both welded and KID. It will not function on any Tennsco Box Locker. The lock is designed to work on lockers with a lift latch mechanism. The lock utilizes a mechanical operation which does not require more than five pounds of force to operate. The user operates the lock by simply inserting the key. This allows the lift latch to be raised and the locker door to open. To lock the locker, the user removes the key and closes the door. The lock has a pivoting deadbolt instead of a horizontally actuaated dead bolt. A set of three keys is supplied with each ZEF-1730 lock. Additional keys can be purchased if needed. ZEF-LK is the model number for an extra key. Please note that this model number is for one key. The ZEF-CK is a Master Key that will open any ZEF-1730 lock within a key series. They are not necessary for the function of a lock. They are only needed if a Master Key is needed. Box Lockers: Please be aware that the MAS-1630 will not work on Tennsco Box Lockers. The dead bolt in the MAS-1630 pivots upward when the lock is operated. The lock requires the upward motion of a lock bar to function. Tennsco Box Lockers are designed to be locked with either a padlock or a horizontally actuated deadbolt lock. The finger pull on Tennsco Box Lockers can be operated using minimal force. It only requires two to three pounds to open a Box Locker Door. No pinching or twisting of the wrist is required to open the Box Locker Door. The Side Reach Guideline does apply to Tennsco Box Lockers only because any opening above 54" or below 9" is not wheelchair accessible. The bottom openings on both the 6-High and 5-High lockers are not compliant. The top two openings of the 6-High and top opening of the 5-High are above 54" so they aren't compliant. The second, third and fourth opeings are fully ADA compliant. Triple Tier Lockers: The lift latch mechanism is ADA compliant for Tennsco's Triple Tier Locker. It can be lifted with less than 5 pounds of force. The lift latch moves up to unlock the door and does not require tight grasping, twisting of the wrist or pinching. Once the lift latch is released, the lock bar drops and the door is closed in a lockable position. The bottom opening of a Tennsco Triple Tier Locker must be modi- fied to make it ADA compliant. The bottom of the locker is 7" high assuming that the lockers without legs will be used on a closed base or raised pedestal. This opening can be made compliant by adding an ADALSI Bottom Riser can be positioned on the bottom shelf. It does not require any tools or hardware and can be removed easily. The riser will add 3" to the height of the bottom shelf raising the top surface to 10". A welded ESL shelf can also be used to make the bottom opening ADA compliant. The shelf can be welded in position 3" above the bottom shelf. The shelf can also be added to a KID unit but holes will have to be drilled. The middle opening on a Triple Tier Locker does not require any modification to make it ADA compliant. The top level is not ADA compliant because most of the opening is above 54". Double Tier Lockers: The lift latch mechanism is ADA compliant for Tennsco's Double Tier Locker. It can be lifted with less than five pounds of force. The lift latch moves up to unlock the door and does not require tight grasping, twisting of the wrist or pinching. Once the lift latch is released, the bar drops and the door is closed in a lockable position. The bottom opening of a Tennsco Double Tier Locker must be modified to make it ADA compliant. The bottom of the locker is 7" high assuming that the lockers without legs will be used on a closed base or raised pedestal. The opening can be made compliant by adding an ADALSI-XXXX Bottom Riser or ESL-XXXXI Shelf. The ADALSI Bottom Riser can be positioned on the bottom shelf. It does not require any tools or hardware and can be removed easily. The riser will add 3" to the height of the bottom shelf, raising the top surface to 10". A welded ESL shelf can also be used to make the bottom opening ADA compliant. The shelf can be welded in position, 3" above the bottom shelf. The top level can be welded in positon, 3" above the bottom shelf. The top level can be made ADA compliant by adding an ADALS-XXXXI shelf 46" from the top of the bottom shelf in the first opening. This will position the coat hooks and top shelf below the 54" maximum height requirement. The shelf can also be added to a KID unit but drilling is required. Single Tier Lockers: The lift latch mechanism is ADA compliant for Tennsco's Single Tier Locker. It can be lifted with less than five pounds of fource. The lift latch moves up to unlock the door and does not require tight grasping, twisting of the wrist or pinching. Once the lift latch is released, the lock bar drops and the door is closed in a lockable position. The opening of a Tennsco Single Tier Locker must be modified to make it ADA compliant. The bottom of the locker is 7" high assuming that the lockers without legs will be used on a closed base or raised pedestal. The opening can be made compliant by adding an ADALSI-XXXX Bottom Riser or ESL-XXXXI Shelf. The ADALSI Bottom Riser can be positioned on the bottom shelf. It does not require and tools or hardware and can be removed easily. The riser will add 3" to the height of the Customer Service: (866) 446-8686 Website: www.tennsco.com E-mail: customerservice@tennsco.com 151 TK0048 12104117 tennsco Storage Made Easy ADA Locker Guidelines bottom shelf, raising the top surface to 10". A welded ESL shelf can also be used to make the bottom opening ADA compliant. The shelf can be welded in position 3" above the bottom shelf. This will position the coat hooks and top shelf below the 54" maximum height requirement. The shelf can also be added to an unassembled unit but drilling is required. 4.2.6* Side Reach: If the clear floor space allows parallel approach by a person in a wheelchair, the maximum high side reach allowed shall be 54" (1370 mm) and the low side reach shall be no less than 9" (230 mm) above the floor. 4.2.3* Wheelchair Turning Space: The space required for a wheelchair to make a 180-degree turn is a clear space of 60" (1525 mm) diameter. 4.2.5* Forward Reach: If the clear floor space only allows forward approach to an object, the maximum high forward reach allowed shall be 48" (1220 mm). The minimum low forward reach is 15" (380mm). A4.1.3(12)(c): Different types of lockers may include full-size and half-size lockers, as well as those specifically designed for storage of various sports equipment. 4.27.4 Operation: Controls and operating mechanisms shall be operable with one hand and shall not require tight grasping, pinching or twisting of the wrist. The force required to activate controls shall be no greater than 5 Ibs (22.2 N). Number Plates: Black plastic number/name plates (2 112" x 7/32") are attached to the recessed door handles. The white lettering is 1/4" high. Aluminum number plates (2 3/8" x 3/4") with 112" high black numbers are attached near the top of the door. Both style plates are attached with rivets. The number sequence or names should be supplied when ordering. Locker Benches / Pedestals: Select grade stock 9 112" wide and 1 1/4" thick, edges and corners beveled. Smooth lacquered finish. Rugged steel pedestals to be positioned a maximum of 4' on center. Benches can be ordered any length to the nearest 6". Heavy duty steel pedestals have an enamel finish to match your lockers. Overall pedestal height is 17 3/4". Benches must be secured to the floor. Locker Sloping Tops: Shall be fabricated from 22-24 gauge steel with a 17 degree slope. Tops are available in single or three wide kits. Tops to be field installed. Locker Sloping Top Filler: Shall be fabricated from 22 gauge steel. Sloping top fillers are used with sloping top lockers to fill the space between two locker sloping tops or a locker top and the wall. Sloping Top Corner Filler: Sloping top corner fill is used with sloping locker tops to fill the corner space between two locker tops. Flat Top Filler: The flat top filler is used on flat locker tops to fill the space between two locker tops or a locker top and the wall. Flat Top Corner Filler: Flat top corner filler is used to fill the corner space between two locker tops. Flat Top Boxed End Panel: Flat top boxed end panels are designed to give a finished look and a sturdier end to a row of free-standing lockers. Sloping Top Boxed End Panel: Sloping top boxed end panels are used with sloping top lockers to give a finished look and a sturdier end to a row of free-standing lockers. Horizontal & Vertical Trim: These decorative trim pieces fill the space between the lockers and the wall when the lockers are recessed. Horizontal trim comes in 72" lengths for custom, onsite trimming. Vertical trim is available in 60" and 72" heights. Splice Cap / Corner Splice Cap / Outside Corner Cap: Splice caps provide a uniform, even join where more than one piece of trim meets. Corner Caps are used to join horizontal and vertical trim pieces. Outside corner caps are used to join trim pieces and turn a corner. Z Brace / Bottom Angle: Z Braces provide reinforcement and secures the bottom of the locker to the floor, while adding toespace under the locker. Bottom angles are used as decorative filler for the bottom face of the locker. 151 Customer Service: (866) 446-8686 Website: www.tennsco.com E-mail: customerservice@tennsco.com TKO048 12104117 nsc(8 Storage Made Easy ADA Locker Guidlines Angle Filler Panel / Flat Filler Panel: Angle filler panels are used to close the space between two lockers when an obstruction prevents the installation of another locker. Flat filler panels require two filler panel frames; angle filler panels require one. Filler Panel Frame / Corner Angle: Filler panel frames attached to locker frames to secure front filler panels. Corner angles are used in inside corners to provide a finished appearance. Coat Rod: These painted (medium grey only) steel rods are 112" diameter and are available in 9",12" 15",18", 21 ", & 24". Coat Hook: Additional coat hooks can be added to any locker. Coat hooks can be factory welded into assembled units if specified at time of order. Singe hook or double hook available. Shelves and Partitions: Add shelves to customize locker compartments or vertical partitions to create dual compartments in single tier lockers. Front Base: Shall be fabricated from 20 gauge steel with four right angle flanges. The front base attaches to the locker frame with four lock ing tabs, no installation tools are required. The base shall fill the opening between the locker frame and the floor. To be used with leg lockers only. End Bases: Shall be fabricated from 20 gauge steel with three right angle flanges and front flange formed to 60 degrees. The end base at- taches to the rear leg with two nuts and bolts. Closed end bases fit between front and rear legs of a row -ending locker. To be used with leg lockers only. Closed Base: Shall be fabricated from 18 gauge steel and electrically welded into a full perimeter base to raise lockers 6" from the floor. Base attaches to lockers with two nuts and bolts. To be used with no -leg lockers only. Locker End: Locker ends are used to finish a row and give a clean, attractive appearance. Grooved Key Lock: This built-in deadbolt lock features a rust -resistant steel case and a large assortment of differing kets. The grooved key lock ensures additional security. Masterkeyed systems are available. Combination Padlock / Masterkeyed Combination Padlock: A self-locking shackle and automatic disarranging tumblers make these locks virtually tamper -proof. Masterkeyed system provides additional control. Shackle Diameter is 9/32" Q mm). Manual Locking Combination Deadbolt / Automatic Locking Combination Deadbolt: Both built-in locks are masterkeyed systems with changeable combinations. The precision mechanism never needs lubrication and a stainless steel case covers the mounting bolt for security. ADA Compliant Key Cap: ADAKC Key Cap will make any master lock sold by Tennsco (that uses a key) ADA compliant. Design increases the size of the key head to make it easier to grip and turn. Customer Service: (866) 446-8686 Website: www.tennsco.com E-mail: customerservice@tennsco.com 151 TKO048 12104117