REVIEWED RESUB1 BLD2024-0779+ACCUSTIC PANEL SPECS+7.1.2024_12.34.14_PM+4352516RES U B BLD2024-0779
CgSorbe Jul 01 2024
CITY OF EDMONDS
DEVELOPMENT SERVICES
DEPARTMENT
Section 09 80 00
FSorb Acoustic Wall and Ceiling Panels
PART
1
GENERAL
1.1
SECTION
INCLUDES
REVIEWED
A.
Sound Attenuation Panels
BY
CITY OF EDMONDS
B.
Sound Attenuation Baffles
C.
Sound Attenuation Grids
1.2
RELATED SECTIONS
A.
09 81 00 - Acoustic Insulation
B.
09 51 00 - Acoustical Ceilings
1.3
REFERENCES
A.
ASTM C423: Sound Absorption by Reverberation Room Method
B.
ASTM E84: Standard Test Method for Surface Burning Characteristics of Building Materials
C.
ASTM E1264: Standard Classification for Acoustical Ceiling Products
D.
UL Laboratories CDPH 2.0 TVOC Testing Standard Method — LEEDv4
E.
Living Building Challenge Criteria: Compliant. LBC Red List Free
F.
Interior Performance: CDPH Standard Method v1.2-2017
1.4
SUBMITTALS
A.
Submit under provisions of Section 01 30 00 - Administrative Requirements.
B.
Product Data: Manufacturer's technical data sheets for each product to be used, including:
1. Recommended cutting and preparation instructions
2. Handling and storage requirements
3. Installation techniques and methods
C.
Shop Drawings:
D.
Selection Samples: For each finish product specified, two sets of color samples representing
manufacturer's full range of available colors and patterns.
E.
Verification Samples: For each finish product specified, two samples, minimum size 2-7/8" x
3-1/2" representing actual product, color, and thickness.
1.5
QUALITY ASSURANCE
A.
Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.
B.
Installer Qualifications: Minimum 2 year experience installing similar products.
Spec Section 09 80 00 - FSorb Acoustic Wall and Ceiling Panels - Tel: 425.881.0888 or 1.844.313.7672 Email: info@fsorb.com
CgSorbe
C. Mock -Up: Provide a mock-up for evaluation of surface preparation techniques and
application workmanship.
1. Finish areas designated by Architect.
2. Do not proceed with remaining work until workmanship is approved by Architect.
3. Confirm consistency of installation. Monitor front surface vs back surface during
installation for consistency unless otherwise specified.
4. Refinish mock-up area as required to produce acceptable work.
1.6 PRE -INSTALLATION MEETINGS
A. Convene minimum two weeks prior to starting work of this section.
1.7 STORAGE, DELIVERY, AND HANDLING
A. Deliver and store product in dry location within unopened manufacturer's packaging bearing
the label with manufacturer's identification until ready for installation.
B. Do not compress or bend product or package during storage.
C. Segregate from strong oxidizers. Keep covered, clean and dry.
D. Avoid handling. Handle materials only when required to avoid damage.
1.8 PROJECT CONDITIONS
A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits
recommended by manufacturer for optimum results. Do not install products under
environmental conditions outside manufacturer's recommended limits.
1.9 SEQUENCING
A. Ensure that products of this section are supplied to affected trades in time to prevent
interruption of construction progress or damage to FSorb material.
1.10 Extra Stock
A. Provide a quantity equal to 2% of total installed or a minimum of two cartons of each type.
New unopened cartons only.
PART 2 PRODUCTS
2.1 MANUFACTURERS
Acceptable Manufacturer: FSorb, located at 21415 87th Ave. SE Woodinville,
WA 98072 — Tel: 425.881.0888 or 1.844.313.7672 Email requests to info@fsorb.com further
details can be found here: https://www.fsorb.com
A. Substitutions: Not permitted
2.2 ACOUSTICAL WALL AND CEILING PANELS
A. Product: FSorb:
1. Design: FSorb
a. Assemble Size: All panels are manufactured at 48"x96" (4'x8')
b. Noise Reduction Coefficient (NRC)
1) ['Y2" - 0.50 (Testing per ASTM C423 - A mount)]
2) [1 "- 0.70 (Testing per ASTM C423 - A mount)]
Spec Section 09 80 00 - FSorb Acoustic Wall and Ceiling Panels - Tel: 425.881.0888 or 1.844.313.7672 Email: info@fsorb.com
CJSorbe
3) [2"- 1.05 (Testing per ASTM C423 - A mount)]
B. Materiel: Thermally bonded (heat pressed) high density, recycled polyester (100%) acoustic
panel containing not less than 65 percent post -consumer materiel.
1. Composition: Unfaced monolithic panel
2. Thickness: '/2" or 1" or 2"
3. Weight: 12 Ibs/cf or 7.5 Ibs/cf or 5 Ibs/cf
4. Colors: Refer to section 2.5
3 SOUND ATTENUATION BAFFLES
A. Product: FSorb:
1. Design: Silentline
a. Assembled Size: All baffles shapes cut from 48"x96" (4'x8') panels.
b. Noise Reduction Coefficient (NRC)
1) [1 /2" — 0.75 Standard (Testing per ASTM C423 - J mount)]
2) [1" — 0.95 (Testing per ASTM C423 - J mount)]
3) [2" — 1.20 (Testing per ASTM C423 - J Mount)]
Design Options:
1) [Ocean]
a) [47" Long Baffles]
b) [95" Long Baffles]
2) [Mountain]
a) [47" Long Baffles]
b) [95" Long Baffles]
3) [ etro]
[47" Long Baffles]
b) 95" Long Baffles]
4) [Trans)
a) [47 ong Baffles]
b) [95" L ng Baffles]
d. Design Length
1) Standard 47" and "Long
2) Custom made from " to 96" (1' to 8')]
f. Design Depth
1) [6"]
2) [8" Standard]
3) [12"]
4) [Custom]
e. Mounting:
1) Eye Lag
2) Dome Cap & Quick Adjust Gripper
3) F-Snap High or Low (For attachment\stan
olt slot ceiling grid)
4) T-Snap High or Low (For attachmentrd 9/16" facedceiling grid)
B. Material: Thermally bonded (heat pressed), high density, recycled polyester (100%) acoustic
panel containing not less than 65 percent post -consumer recycled material.
1. Composition: Unfaced monolithic panel.
2. Thickness: ['/2" or 1" or 2"]
3. Weight: 12 Ibs/cf or 7.5 Ibs/cf or 5 Ibs/cf
4. Colors: Refer to Section 2.5
Spec Section 09 80 00 - FSorb Acoustic Wall and Ceiling Panels - Tel: 425.881.0888 or 1.844.313.7672 Email: info@fsorb.com
CJSorbe
2.4 SOUND ATTENUATION GRIDS
A. Product: FSorb
1. Design: Quietgrid
a. Assembled Size: All Quietgrid shapes cut from 48"x96" (4'x8') panels.
b. Noise Reduction Coefficient (NRC)
1) [1/2" — 0.95 (Testing per ASTM C423 - J mount)]
C. Design Options:
1) [47", 71 ", or 95" Angle (A)]
2) [47", 71 ", or 95" Chevron (K)]
3) [47", 71 ", or 95" Curve (C)]
4) [47", 71", or 95" Square (S)]
5) [ 48 Ocean]
a) [Tegular Lay -in (T)]
b) [Shift and Set (SS)]
6) [48 Mountain]
a) [Tegular (T)]
b) [Shift and Set (SS)]
7) [48 Metro]
a) [Tegular (T)]
b) [Shift and Set (SS)]
8) 48 Metro Block]
a) [Tegular (T)]
b) [Shift and Set (SS)]
9) [4 Transit]
[Tegular (T)]
b [Shift and Set (SS)]
d. Design epth
1) [6"]
2) [8" Sta dard]
3) [12"]
4) [Custom]
B. Material: Thermally bonde (heat pressed), high density, recycled polyester (100%)
acoustic panel containing no less than 65 percent post -consumer recycled material.
1. Composition: Unfaced Ono lithic panel.
2. Thickness: [1/2"]3. Weight: [12 Ibs/cf]
4. Colors: Refer to Section 2.5
2.5 FSORB COLORS
A. Finish: Unfaced panel color options:
Standard Colors:
a.
[White #100]
b.
[Light Grey #130]
c.
[Grey #160]
d.
[Tan #190]
e.
[Charcoal #220]
f.
[Black #250]
Premium Colors:
a. [Light Beige #300]
b. [Rose Red #330]
Spec Section 09 80 00 - FSorb Acoustic Wall and Ceiling Panels - Tel: 425.881.0888 or 1.844.313.7672 Email: info@fsorb.com
CJSorbe
c.
[Red #360]
d.
[Pink #390]
e.
[Orange #420]
f.
[Apricot #450]
g.
[Yellow #480]
h.
[Dark Green #510]
i.
[Green #540]
j.
[Moss Green #570]
k.
[Sea Foam Green #600]
I.
[Midnight Blue #630]
m.
[True Blue #660]
n.
[Ocean Blue #690]
o.
[Sky Blue #720]
p.
[Dark Purple #750]
q.
[Purple #780]
r.
[Chestnut #810]
3.1 EXAMINATION
B. Do not begin installation until substrates have been properly prepared.
C. If substrate preparation is the responsibility of another installer, notify Architect of
unsatisfactory preparation before proceeding.
3.2 PREPARATION
A. Clean surfaces thoroughly prior to installation.
D. Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
3.3 INSTALLATION
A. Locate system in accordance to the reflected plan and/or elevations. Install acoustical panels in
location indicated. Follow the installation recommendations of the manufacturer. Align panels
accurately, with edges plum and top edges level.
B. Install panels to construction tolerance of plus or minus 1/8 inch for the following:
1) Plumb and Level
2) Flatness
3) Width of joints
E. Cutting Acoustical Units: Make field cut edges of same profile as factory edges.
F. Fit units in place, free from damaged edges or other defects detrimental to appearance and
function.
G. Install acoustical units level, in uniform plane, and free from twist, warp, and dents.
H. Install units using adhesives, mechanical fasteners or clips to walls or ceilings as directed.
The use of a suspension system, blocking or furring may be required.
3.4 TOLERANCES
Spec Section 09 80 00 - FSorb Acoustic Wall and Ceiling Panels - Tel: 425.881.0888 or 1.844.313.7672 Email: info@fsorb.com
CJSorbe
A. Maximum variation from flat and level surface: 1/8 inch in 10 feet.
B. Maximum variation from plumb of suspension system caused by eccentric loads: 2 degrees.
3.5 PROTECTION
A Protect installed products until completion of project.
B Touch-up, repair or replace damaged products before Substantial Completion.
Spec Section 09 80 00 - FSorb Acoustic Wall and Ceiling Panels - Tel: 425.881.0888 or 1.844.313.7672 Email: info@fsorb.com