REVIEWED BLD2024-1478+Interior_Lighting_Summary+11.8.2024_4.06.41_PM+46108372021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
Project: RECEIVED
Edmonds Medical Pavilion - Suite 100 TI - 2021 WSEC 11 /$/24 REVIEWED
7320 216th Street BY
BLD2024-1478 CITY OFEDMONDS i
Suite 100 CITY OF EDMONDS BUILDING DEPARTMENTS
DEVELOPMENT ...............................................:
Edmonds, WA 98026 SERVICES DEPARTMENT
Date: 2024-11-08
Applies
Code Section
Component
Compliance Information Required In Permit
Location in
Building Department
Documentation
Documents
Notes
LIGHTING SCOPE
C103.1
Construction
For a shell & core or tenant space (first build -
documents - General
out) project, indicate if there is no lighting
scope included in the project.
NA
C103.1
Construction
For an alteration project, indicate if there is
documents - General
no lighting scope included in the project.
NA
C405.1
Lighting in sleeping
Indicate general compliance path for
units
permanently installed luminaires in sleeping
units - vacancy controls & luminaire efficacy;
or lighting power allowance.
INTERIOR LIGHTING CONTROLS
YES
C405.2
Interior lighting
For all interior lighting systems, indicate
E2.00
controls, general
lighting control method (general lighting
controls requirements or luminaire level
lighting controls) on plans for all spaces and
lighting zone(s) served; indicate exceptions
applied to eligible spaces and light
YES
C405.2.3
Manual controls
Indicate on plans the method of manual
E2.00
lighting control, location of manual control
device and the area or specific application it
serves.
YES
C405.2.4
Manual interior light
For general lighting not controlled by
E2.00
C405.2.4.1
reduction controls
occupancy sensors, indicate on plans which
method of manual 50% lighting load
reduction is provided, or indicate applicable
exception.
YES
C405.2.1
Method of automatic
Indicate on plans the method of automatic
E2.00
C405.2.2
shut-off control
shut-off control during unoccupied periods
(occupancy sensor or time switch) for all
lighting zones.
YES
C405.2.1
Occupant sensor
Indicate on plans all luminaires that are
E2.00
controls
controlled by occupant sensor controls;
indicate controls are configured to turn
luminaires 100% off when the space is
unoccupied
YES
C405.2.1
Occupant sensor
Indicate if occupant sensor controls are
E2.00
C405.2.1.1
controls
configured to be manual on or automatic on to
not more than 50% power; indicate spaces
eligible for exception that allows automatic on
to 100% power.
NA
C405.2.1.2
Occupant sensor
Indicate each aisleway within a warehouse or
controls - warehouse
library stack space designated as a separate
storage areas &
zone that is independently controlled
library stacks
Page 1113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
NA Indicate occupant sensors are configured to
NA C405.2.1.2 Occupant sensor
controls - warehouse
storage areas &
library stacks
NA C405.2.1.3 Occupant sensor
controls - open plan
office areas
NA C405.2.1.3 Occupant sensor
controls - open plan
office areas
NA C405.2.1.4 Occupant sensor
controls - enclosed
fire -rated stairwells
YES C405.2.1.5 Occupant sensor
controls - corridors
NA C405.2.2.1 Automatic time
switch controls
NA
NA
NA C405.2.5.2 Daylight zones -
C405.2.5.4 Sidelit zones
NA
NA
NA C405.2.5 Daylight responsive
C405.2.5.I controls
automatically reduce lighting power by _ 50%
when the zone is unoccupied for over 20
minutes; indicate controls are configured to
automatically restore lighting to full power
when the zone or space is occupie
Indicate method of automatic 100% shut-off
(occupancy sensor or time switch)
For open plan office areas larger than 300 sf,
indicate all general lighting control zones are
< 600 sf
Indicate all general lighting control zones are
provided with vacancy controls that are
configured to reduce lighting power by not
less than 80% when the zone is unoccupied
and turn luminaires 100% off when the
control zone is unoccupied; indicate unoccup
Indicate stairway lighting is provided with
occupancy sensor controls that reduce lighting
power by not less than 50% when the stairway
in unoccupied and restore lighting to 100%
when it is occupied.
Indicate corridor lighting is provided with
E2.00
occupancy sensor controls that reduce lighting
power by not less than 50% when the corridor
is unoccupied.
Indicate spaces on plans where time switch
controls are configured to turn luminaires
100% off during unoccupied hours
Indicate spaces on plans where time switch
controls are configured to turn on lighting to
full power versus 50% power
Indicate locations of override switches on
plans and the lighting zone(s) served; indicate
that the area(s) served by each override switch
does not exceed 5,000 sf.
Indicate primary and secondary sidelit
daylight zone floor areas on plans
For small vertical fenestration assemblies
(rough opening less than 10% of primary
daylight zone floor area) where daylight
responsive controls are not required, provide
fenestration area to daylight zone floor area
calculation(s).
Indicate toplit daylight zone floor areas on
plans.
Indicate on plans all lighting zone(s) served by
daylight responsive controls; indicate that the
area served by each control device does not
exceed 2,500 SF
Page 2113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
NA
Identify sidelit and toplit daylight zones that
are not provided with daylight responsive
controls and the exception(s) that apply
NA
C405.2.5.1
Daylight responsive
Indicate on plans that all daylight responsive
controls
controls provide continuous dimming to
<15% full light output
NA
C405.2.5.1
Daylight responsive
Indicate that daylight responsive controls are
controls
configured to completely shut off all
controlled lighting fixtures within the lighting
zone.
NA
C405.2.6
Additional controls -
Identify spaces and lighting fixtures on plans
Specific application
that require specific application lighting
lighting controls
controls per this section.
NA
C405.2.6,
Additional lighting
Indicate on plans that all display, accent and
Items 1.1 thru
controls for display,
supplemental task lighting fixtures are
1.6
accent &
controlled independently from general area
supplemental task
lighting
lighting
NA
C405.2.6,
Display and accent
For display and accent lighting fixtures,
Items 1.1 and
lighting
including lighting fixtures added per the
1.2
C405.2.2.1 additional interior lighting power
allowance, indicate on plans the separate
manual controls for these fixtures and the type
of automatic off controls (occupanc
NA
For display case lighting fixtures, indicate on
plans the separate manual controls for these
fixtures and the type of automatic off controls
(occupancy sensor or time -switch)
NA
C405.2.6,
Supplemental task
For supplemental task lighting fixtures
Item 1.4
lighting
including under -shelf or under -cabinet
lighting, indicate on plans the separate manual
controls for these fixtures and the type of
automatic off controls (occupancy sensor or
time -switch)
NA
C405.2.6,
Lighting equipment
For lighting equipment for sale or
Item 1.5
for sale or
demonstration, indicate on plans the separate
demonstration
manual controls for these fixtures and the type
of automatic off controls (occupancy sensor
or time -switch)
NA
For exhibit lighting fixtures in galleries,
museums and monuments, indicate on plans
the separate manual controls for these fixtures
and the type of automatic off controls
(occupancy sensor or time -switch).
C405.2.6,
Permanently installed
Indicate method of automatic off control of
Item 2
lighting in sleeping
all installed luminaires in sleeping units
units
(vacancy or captive key card control); also
refer to Receptacles.
Page 3113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
NA
C405.2.6,
Lighting for non-
For lighting serving non -visual applications
Item 3
visual applications
(food warming and lighting for life support of
nonhuman life forms), indicate on plans that
lighting fixtures are controlled independently
from both general area lighting and other
lighting applications within
NA
Indicate on plans separate manual controls for
non -visual lighting application fixtures and
applicable automatic lighting controls;
indicate that the area served by each control
device does not exceed 4,000 sf.
NA
For task lighting that serves medical & dental
purposes, indicate on plans that lighting
fixtures are provided with manual control that
is independent from general area lighting.
YES
C405.2.6,
Means of egress
Identify all means of egress lighting fixtures
E2.00
Item 5
lighting
on plans including fixtures that function as
both normal and emergency illumination
YES
Provide calculation for total lighting power
E2.00
density (LPD) of all means of egress lighting
fixtures; if total LPD is _ 0.01 Watts/SF,
indicate on plans the method of automatic
shut-off control during unoccupied periods
(emergency relay & occupancy sens
NA
C405.2.8
Advanced lighting
For open office areas _ 5,000 sf, indicate
controls in open
which advanced lighting control system is
office areas
provided (luminaire level lighting controls or
networked lighting controls).
C405.2.8.1
Luminaire level
Where LLLC are provided to comply with
lighting controls
C405.2.8, or provided as the alternate lighting
(LLLC)
controls compliance method per C405.2, or to
comply with C406.2.4.2 Enhanced digital
interior lighting controls; provide sequence of
operations that describes required
NA
C405.2.8.1
Luminaire level
Indicate on plans that each LLLC luminaire is
C405.2.8.3
lighting controls
configured with occupancy sensing control
(LLLC)
functions (including C405.2.1.3 requirements
for open office areas) and continuous full
range dimming controls to brighten or dim
lights based on occupancy and availab
NA
C405.2.8.2
Networked lighting
Where NLC are provided to comply with
control (NLC)
C405.2.8, or to comply with C406.2.4.2
Enhanced digital interior lighting controls;
provide sequence of operations that describes
required NLC capabilities and performance
parameters
NA
C405.2.8.2
Networked lighting
Indicate on plans that each NLC luminaire is
C405.2.8.3
control (NLC)
individually addressable or document
exception applied; Indicate on plans that each
NLC luminaire is configured with occupancy
sensing control functions (including
C405.2.1.3 requirements for open office
areas)
Page 4113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
NA
C405.8.3
High end trim
Where high end trim is required, luminaires
shall be initially configured to limit maximum
lumen output or lighting power to 85% or to
the target design lighting power.
INTERIOR LIGHTING CONTROLS - ADDITIONAL ENERGY EFFICIENCY MEASURE
C406.2.4.2
Enhanced digital
To comply with the enhanced interior lighting
interior lighting
controls measure, provide calculations that
controls
demonstrate that lighting in _ 50% of the
project floor area is provided with LLLC
(C405.2.8.1) or NLC (C405.2.8.2) controls
with high end trim (C405.2.8.3)
Where LLLC is provided, indicate on plans
that each LLLC controlled luminaire is
configured with integral sensors; where NLC
is provided, indicate on plans that each NLC
controlled luminaire is configured to be
independently addressable; provide sequence
NA
C406.2.4.1
Enhanced lighting
In Group R-2 occupancies, indicate on plans a
controls in Group R-2
master control at the main entrance to each
dwelling or sleeping unit that switches off all
lights and switched receptacles (may be two
controls, one for lights and the other for
receptacles); indicate on plan
INTERIOR LIGHTING CONTROLS - LIGHTING LOAD MANAGEMENT MEASURE
NA
C406.3.1
Interior lighting DDC
To comply with the interior lighting load
controls & real-time
management measure, indicate automatic
demand response
lighting controls are connected to a central
DDC system capable of activation by an
external utility signal; where utility real-time
demand or pricing program exists, indicat
NA
C406.3.1
Interior lighting
Indicate lighting controls are configured to
power reduction
gradually reduce by continuous dimming the
controls
interior general area lighting power by ? 20%
in response to a peak demand signal; calculate
the percentage of total building floor area
served by load management ligh
NA
C406.3.1
Warehouse & retail
For warehouse & retail storage areas, indicate
storage interior
method of interior general area lighting power
lighting power
reduction (continuous dimming by ? 20%;
reduction controls
switching off ? 25% of lighting power).
EXTERIOR LIGHTING CONTROLS
C405.2.9
Exterior lighting
For all exterior lighting, indicate on plans
C405.2.9.1
controls
automatic controls (either daylight sensing or
C405.2.9
astronomic time clock) configured to turn
lighting off when daylight is present; or
indicate exception applied.
For exterior building facade & landscape
lighting, indicate that controls are configured
to turn this lighting off when daylight is
present for a minimum of 6 hours per night,
or from 1 hour after closing to 1 hour before
opening per the occupancy schedul
Page 5113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
C405.2.10 Parking garage
lighting control
C405.2.10 Parking garage
lighting control -
Perimeter lighting
zones
C405.2.10 Parking garage
lighting control - Eye
adaptation lighting
NA C405.3 Lighting for plant
growth and
maintenance
C405.5.4 Exterior gas -fired
lighting appliances
INTERIOR & EXTERIOR LIGHTING CONTROL C
NA C405.2.7 Area controls -
Master control
switches
NA
INTERIOR LIGHTING POWER & EFFICACY
YES C405.4.1 Total connected
interior lighting
power
For outdoor parking area (not parking garage)
luminaires that are mounted <_ 24 feet high
and are rated at _ 40 watts, indicate that
controls are configured to turn this lighting
off when daylight is present; in addition,
indicate controls are config
For exterior lighting other than building
facade, landscape and outdoor parking area
lighting, indicate controls are configured to
reduce lighting power by at least 50% from
12am-6am, or 1 hour after closing to 1 hour
before opening, or when no activity i
Indicate all interior parking garage lighting
fixtures are provided with time switch
controls (per C405.2.2.1) or occupancy sensor
controls (per C405.2.1.1); indicate controls
are configured to reduce lighting power by at
least 30% when no activity is det
For parking garage lighting fixtures located
within 20 feet of perimeter wall openings,
indicate on plans that daylight sensing controls
are configured to reduce lighting power by at
least 50%, or exception applied
For lighting fixtures at vehicle entrances &
exits, indicate on plans that daylight sensing
controls are configured to reduce lighting
power by at least 50% from sunrise to sunset.
For permanently installed lighting fixtures
used specifically for plant growth and
maintenance, indicate that the photosynthetic
photon efficacy measured at the lamp or
luminaire is _ 1.7 3Z%2mol/J in greenhouses
and _ 1.9 iLlhmol/J in all other indoo
Indicate ignition system is a method other
then continuously burning pilot light.
IRCUITS
Indicate location(s) of lighting master control
switch(es) intended to control multiple
independent switches; a circuit breaker may
not be used as a lighting master control switch
Verify the maximum power controlled by any
single lighting control switch or automatic
control device is no more than a 20 amp
circuit loaded to ? 80%.
Include all luminaires in interior lighting
fixture schedule; indicate fixture types, lamps,
ballasts and rated watts per fixture; include
rated wattage of lamps for luminaires with
lamps connected directly to building power;
include wattage limit of tran
Page 6113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
YES
Identify spaces eligible for lighting power
E2.00
exemption on plans and in WSEC interior
lighting compliance reports; indicate the
exception applied
YES
Identify lighting equipment eligible for
E2.00
lighting power exemption in fixture schedule
and in WSEC interior lighting compliance
reports; indicate the exception applied.
C405.1.1
Lighting in dwelling
Include all permanently installed luminaires in
units
dwelling units in interior lighting fixture
schedule; include luminaire lighting power
and efficacy (lumens)
Include all permanently installed luminaires in
sleeping units in interior lighting fixture
schedule; include luminaire lighting power or
efficacy (lumens) depending on compliance
path taken per C405.1
NA
For all permenantly installed luminaires,
indicate in interior lighting fixture schedule
that rated lamp efficacy is _ 65 lumens/watt
or luminaire efficacy is _ 45 lumens/watt.
YES
C405.4.2
Interior lighting
Indicate which interior LPA method is
E2.00
power allowance
applied to the entire building (Building Area
(LPA)
Method or Space -by -Space Method); indicate
LPA applied is Space -by -Space Method for
partial building projects and for buildings
with unfinished spaces.
INTERIOR LIGHTING POWER CALCULATION - INDICATE COMPLIANCE PATH TAKEN
NA
C405.4.2.1
Building Area
Demonstrate that total proposed interior
Method
lighting wattage per building does not exceed
the sum of the maximum allowed wattages for
all building area types; identify locations of
building areas on plans; provide WSEC
interior lighting compliance reports.
YES
C405.4.2.2
Space -By -Space
Demonstrate that total proposed interior
E2.00
Method
lighting wattage does not exceed the
maximum allowed wattage; identify locations
of space types on plans, including additional
allowance retail display areas and areas with
display, highlight and decorative lightin
INTERIOR LIGHTING POWER & EFFICACY - ADDITIONAL ENERGY EFFICIENCY MEASURES
NA
C406.2.3.1
Reduced interior
To comply with the reduced interior LPD
C406.2.3.2
lighting power
additional energy efficiency measure,
density (LPD)
demonstrate that total proposed interior LPD
wattage is 10% or 20% lower than the total
interior LPA wattage for the area the reduced
lighting power measure is being applied to
Page 7113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
C406.2.3.3
Reduced interior
To comply with reduced interior LPD
LPD - Dwelling &
additional energy efficiency measure for a
sleeping unit lamp
building with dwelling units or sleeping units,
efficacy
indicate in interior lighting fixture schedule
that all permenantly installed luminaires have
a rated lamp efficacy _ 90 fume
EXTERIOR LIGHTING POWER & EFFICACY
C405.5.2
Total connected
Include all luminaires in exterior lighting
exterior lighting
fixture schedule; indicate fixture types, lamps,
power
ballasts and rated watts per fixture; include
rated wattage of lamps for luminaires with
lamps connected directly to building power;
include wattage limit of tran
Identify exterior lighting applications eligible
for lighting power exemption on plans and in
WSEC exterior lighting compliance reports;
indicate the exception applied.
TABLE
Exterior lighting zone
Indicate the building exterior lighting zone as
C405.5.3(1)
specified by the AHJ.
C405.5.1
Exterior building
For building grounds lighting fixtures rated at
grounds lighting
greater than 25 watts, indicate in exterior
lighting fixture schedule that fixtures have a
rated lamp efficacy _ 100 lumens/watt or
indicate the exception applied.
EXTERIOR LIGHTING POWER CALCULATION
C405.5.3
Exterior lighting
Demonstrate that total proposed exterior
power allowance
surface lighting wattage does not exceed the
(LPA)
maximum allowed wattage (including base
site allowance); identify locations of exterior
surfaces on plans; provide WSEC exterior
lighting compliance reports
Demonstrate that total proposed wattage for
each additional allowance exterior surface
type does not exceed the LPA for the surface
type (includes base site allowance remaining
after C405.5.3 LPA calculation); identify
locations of additional allowance ex
LIGHTING SYSTEMS ALTERATIONS
YES
C503.7.1
New lighting systems
Where new interior or exterior lighting
E2.00
and controls
systems are installed within an existing
building site, indicate new lighting controls
comply with C405.2; indicate commissioning
of lighting controls (C408.4) and lighting
system energy end -use metering (C409.3) wi
NA
C503.7.2
Interior lighting &
Include all new luminaires in interior lighting
E2.00
parking garage
fixture schedule in plans, provide same
lighting alteration
lighting fixture information as for new
construction per C405.4.1 and C405.4.2
Page 8113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
NA C503.7.2 Interior lighting
alterations (LPA) -
Add/replace
YES C503.7.2 Interior lighting
alterations (LPD) -
Add/replace
C503.7.2 Exterior lighting
alterations (LPA) -
Add/replace &ge
20%
C503.7.2 Exterior lighting
alterations (LPD) -
Add/replace &ge
20%
C503.7.2 Exterior lighting
alterations (LPA) -
Add/replace
C503.7.2 Exterior lighting
alterations (LPD) -
Add/replace
YES C503.7.3 Interior lighting
wiring & circuiting
alterations
For alterations that add or replace _ 20% of
luminaires within an interior space or parking
garage, indicate which interior lighting power
allowance (LPA) method is applied to the
alteration project area (Space -by -Space
Method for partial building alte
Demonstrate that total proposed interior
lighting wattage (including existing -to -remain
lighting wattage) within the alteration project
area does not exceed the maximum allowed
wattage (Space -by -Space Method) or the sum
of the maximum allowed wattages for
For alterations that add or replace < 20% of
luminaires in an interior space or parking
garage, calculate total existing interior lighting
wattage within the project area prior to the
alteration
Demonstrate that total proposed interior
E2.00
lighting wattage (including existing -to -remain
lighting wattage) within the alteration project
area does not exceed the total existing interior
lighting wattage prior to the alteration;
provide WSEC interior lighti
Include all new luminaires in exterior lighting
fixture schedule in plans, provide same
lighting fixture information as for new
construction per C405.5.2
For alterations that add or replace _ 20% of
exterior lighting wattage, indicate exterior
lighting power allowance (LPA) calculated in
the same manner as for new construction
Demonstrate that total proposed exterior
lighting wattage (including existing -to -remain
lighting wattage) does not exceed the
maximum allowed wattage; identify locations
of surface types on plans, including additional
allowance surfaces; provide WSEC exte
For alterations that add or replace < 20% of
exterior lighting wattage, calculate total
existing exterior lighting wattage prior to the
alteration
Demonstrate that total proposed exterior
lighting wattage (including existing -to -remain
lighting wattage) does not exceed the total
existing exterior lighting wattage prior to the
alteration; identify locations of surface types
on plans, including additio
Where new wiring is installed to serve new
E2.00
interior luminaires and /or luminaires are
relocated to a new circuit; indicate manual
and automatic lighting controls are provided
(as applicable) - manual & light reduction
(C405.2.3 & C405.2.4); occupancy sens
Page 9113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
Where new wiring is installed to serve new
exterior luminaires and /or luminaires are
relocated to a new circuit; indicate circuit
power area controls (C405.2.7) are provided;
indicate commissioning of exterior lighting
controls (C408.4) will be provided,
C503.7.4
Lighting panel
Where a new interior and/or exterior lighting
alterations
panel is installed or an existing panel is moved
(including all new raceway and conductor
wiring), indicate all of the same interior
lighting controls requirements as for wiring &
circuiting alterations apply,
C503.7.5
Newly -created rooms
Where interior space(s) are reconfigured
(permanently installed walls or ceiling -height
partitions) to create new enclosed spaces,
indicate the following manual and automatic
lighting controls are provided (as applicable) -
manual & light reduction (C405.
NA
C504.2
Lighting repairs
Identify existing luminaires being upgraded
with bulb and / or ballast replacement;
indicate fixture alteration does not increase
existing fixture wattage
NA
C505.1
Change of interior
Identify spaces on plans where the building
space use
area type or space use type is being changed
from one type to another per Tables
C405.4.2(1) or (2) including additional
allowance retail display areas and areas with
display, highlight and decorative lighting
NA
Demonstrate that total proposed interior
lighting wattage (including existing -to -remain
lighting wattage) within the alteration project
area does not exceed the maximum allowed
wattage (Space -by -Space Method) or the sum
of maximum allowed wattage per each
RECEPTACLES
YES
C405.10
Automatic receptacle
Provide schedule on electrical plans that lists
E3.00
control
the number of controlled and uncontrolled
receptacles in each space where controlled
receptacles are required - classrooms,
enclosed offices, conference rooms,
copy/print rooms, break rooms and individual
wo
YES
Identify all controlled and uncontrolled
E3.00
receptacles on electrical plans; indicate that _
50% of all receptacles are provided with
automatic controls in each space where they
are required; include receptacle configuration
such as spacing between contro
YES
Indicate on plans the method of automatic
E3.00
control for each controlled receptacle zone
(occupant sensor or programmable time -of -
day control); indicate that the area served by
each control device does not exceed 5,000 sf.
Page 10113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
C405.2.6,
Switched receptacles
Indicate method of automatic off control of
Item 2
in sleeping units
all switched receptacles in sleeping units
(vacancy or key card control).
NA
C405.7.1
Electric receptacles at
In all designated appliance locations within
dwelling unit gas
dwelling units (kitchen cooking appliances,
appliances
laundry and domestic water heating), indicate
electric receptacles or junction box & circuit
within 12 inches of the appliance location
with sufficient capacity to se
NA
C503.7.7
Electrical receptacle
For alteration project areas _ 5,000 sf where
alerations
electric receptacles are added or replaced,
indicate receptacles are provided with
automatic controls per C405.10, or exception
applied.
ELECTRIC MOTORS
C405.8
Electric motor
Include all motors, including fractional hp
efficiency
motors, in electric motor schedule on
electrical plans; indicate motor type,
horsepower, rpm, rated efficiency, or
exception applied.
ELEVATORS, ESCALATORS & MOVING WALKS
C405.9.1
Elevator cabs
For luminaires in each elevator cab, provide
calculations that demonstrate average efficacy
is not less than 35 lumens per watt
For elevators that do not have an integral air
conditioning system, indicate rated watts per
cfm for elevator cab ventilation fans do not
exceed 0.33 watts per cfm
Indicate automatic controls that de -energize
lighting and ventilation fans when elevator is
stopped and unoccupied for a period of 15
minutes or more.
C405.9.2
Escalators and
Indicate escalators and moving walks comply
moving walks
with ASME A17.1/CSA B44 and are provided
with automatic controls that are configured to
reduce operational speed to the minimum
permitted when not in use, or exception
applied.
C405.9.3
Escalator energy
Indicate escalators are designed to recover
recovery
electrical energy when resisting overspeed in
the down direction.
RENEWABLE ENERGY
NA
C411
Renewable Energy
For new construction, including additions,
change of use, and change of occupancy, with
floor area _ I 0000sf ;provide documentation
of on -site renewable energy capacity; provide
calculations supporting applicable exceptions;
if qualifying by exception provide an
accounting for the additional Additional
Energy Efficiency Credits that will be
required
Page 11113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
RENEWABLE ENERGY - ADDITIONAL ENERGY EFFICIENCY MEASURE
NA
C406.2.5
On -site and off -site
To comply with the renewable energy
renewable energy
measure, provide an accounting of on -site and
any contracted off -site renewable energy
capacity; for all off -site sources, indicate the
C411.2 renewable energy source type, energy
factor, and the rated capacity and calculated
code credited kW; indicate on -site renewables
used to comply with C411 or for a code
exception elsewhere in the code; with the
remaining renewable energy provide Equation
4-17 calculations showing the achieved credits
and that the achieved credits are ? the base
credits for the measure
NA
C406.2.5
On -site and off -site
Provide documentation that all off -site
renewable energy
renewable energy systems comply with
Sections C411.2.2 and C411.2.3 including all
contracts, and the ownership and location of
off -site generation
ELECTRIC ENERGY STORAGE - LOAD MANAGMENT MEASURE
NA
C406.3.4
Electric energy
To comply with the electrical energy storage
storage
load managment measure, indicate automatic
controls shall store electricity in electric
storage devices during nonpeak periods and
use stored energy during peak periods;
Document the total electric storage device
capacity; indicate it is ? 5 Wh/sf (58 Wh/sm)
of gross building area; for proration provide
the proration calculations supporting the
claimed credit
GENERAL ELECTRICAL SYSTEMS
C405.6
Electrical
Include electrical transformer schedule on
transformers
electrical plans; indicate transformer type,
size (kVA), efficiency, or exception applied.
C405.7
Dwelling unit
Indicate on electrical plans that each dwelling
electrical energy
unit in a Group R-2 building has a separate
consumption
electrical energy meter, or exception applied.
NA
C405.11
Voltage drop
Indicate wire conductors are sized so that the
maximum voltage drop from customer service
conductors to branch circuit conductors is Me
5%.
NA
C405.12
Alternating current-
Indicate in plans that AC -output UPS systems
output uninterruptible
serving computer rooms meet or exceed the
power supplies (AC-
calculation and testing requirements identified
output UPS)
in ENERGY STAR Program Requirements
for Uninterruptible Power Supplies (UPS) ?
Eligibility Criteria Version 2.0.
COMMISSIONING (CX)
Page 12113
2021 WSEC Requirements for Commercial Buildings including Group R2, R3 & R4 over 3 stories & all R1 -- Administered by @2024 NEEA, All rights reserved
The following information is necessary to check a permit application for compliance with the lighting systems, motors and electrical system requirements in the
Washington State Energy Code, Commercial Provisions.
For questions about this report, contact WSEC Commercial Technical Support at 360-539-5300 or via email at com.techsupport@waenergycodes.com
YES
C408.4
Scope of electrical
Indicate that all electrical systems
E0.01
power & lighting
(receptacles, transformers, motors, vertical &
systems
horizontal transportation) for which the
commissioning
WSEC requires control functions and/or
configuration to perform specific functions
are required to be commissioned; include
docume
YES
Where total building lighting load is _ 10 kW
E0.01
or the total lighting load of luminaires
requiring daylight sensing and/or occupancy
control is _ 5 kW, indicate that all automatic
lighting control systems are required to be
commissioned; or provide ca
YES
C408.1.1
Commissioning
Indicate Cx requirements in plans and
E0.01
requirements in
specifications for all applicable electrical and
construction
lighting control systems
documents
YES
C408.1.2
Commissioning
General summary of Cx plan shall include the
E0.01
C103.6.3
requirements in
following: 1) Narrative description of
construction
activities; 2) Responsibilities of the Cx team;
documents
3) Schedule of activities including verification
of project close out documentation (C103.6);
4) Conflict of interest plan
YES
C408.1.3
Commissioning
Include in general summary that a Cx project
E0.01
C408.1.4
requirements in
report and Cx Compliance Checklist (Figure
construction
C408.1.4.1) shall be completed by the
documents
Certified Cx Professional and provided to the
owner prior to the final electrical inspection.
YES
C408.4.1
Functional
Identify in plans and specifications the
E0.01
performance testing
intended operation of all electrical equipment
criteria
and controls during all modes of operation,
including interfacing between new and
existing -to -remain systems.
PROJECT CLOSE OUT
YES
C103.6.3
Documentation
Indicate in plans that project close out
E0.01
requirements
documentation is required; indicate
information shall include WSEC lighting
compliance reports that document all interior
lighting areas and space types, exterior
lighting surface types, interior/exterior
lighting
If "no" is selected for any question, provide explanation.
Page 13113